ROBLIN OPEN 610 User manual

2108
Instructions Booklet
Mode d’emploi
Bedienungsanleitung
Gebruiksaanwijzing
Open 610

2
Contenents - Sommaire
OR THE USER ...................................................................................................... 4
DEFINITION .................................................................................................................. 4
Important Recommendations ........................................................................................ 4
USAGE .......................................................................................................................... 5
MAINTENANCE............................................................................................................. 5
OR THE INSTALLER ............................................................................................ 6
INSTALLATION ..............................................................................................................
EVACUATION DIRECTLY OUTDOORS........................................................................ 8
EVACUATION BY RECYCLING .................................................................................... 9
ELECTRICAL CONNECTION ..................................................................................... 10
POUR L’UTILISATEUR ......................................................................................... 11
DÉFINITION ................................................................................................................ 11
Recommandations Importantes ................................................................................... 11
UTILISATION ............................................................................................................... 12
ENTRETIEN ................................................................................................................ 12
POUR L’INSTALLATEUR ...................................................................................... 13
INSTALLATION ............................................................................................................ 13
EVACUATION DIRECTE VERS L’EXTÉRIEUR .......................................................... 15
EVACUATION EN RECYCLAGE................................................................................. 1
RACCORDEMENT ÉLECTRIQUE .............................................................................. 17

Inhalt - Inhoud
ÜR DEN BENUTZER........................................................................................... 18
DEFINITION ................................................................................................................ 18
WICHTIGE HINWEISE ................................................................................................ 18
BEDIENUNG ............................................................................................................... 19
WARTUNG .................................................................................................................. 19
ÜR DEN INSTALLATEUR ................................................................................... 20
MONTAGE ................................................................................................................... 20
DIREKTER ABZUG NACH AUSSEN .......................................................................... 23
UMLUFTBETRIEB ....................................................................................................... 23
ELEKTRISCHER ANSCHLUSS .................................................................................. 24
VOOR DE GEBRUIKER ........................................................................................ 25
BESCHRIJVING .......................................................................................................... 25
BELANGRIJKE AANBEVELINGEN ............................................................................. 25
GEBRUIK..................................................................................................................... 2
ONDERHOUD ............................................................................................................. 2
VOOR DE INSTALLATEUR .................................................................................. 27
INSTALLATIE ............................................................................................................... 27
DIRECTE AFVOER NAAR BUITEN ............................................................................ 30
AFVOER BIJ CIRCULATIEKAP .................................................................................. 30
ELECTRISCHE AANSLUITING ................................................................................... 31

4
OR THE USER
Now that your cooker hood has been installed in accordance with the “ or the
itter” part of these instructions by an authorized specialist,
please read the following pages carefully. This will help you to become familiar
with and to make the best use of the features of your appliance.
DEFINITION
- These appliance are extendable hoods designed to be installed in the place of a tall
60 cm wide kitchen unit.
- They can be adapted to all units in which the body depth (excluding the door) is
between 270 mm and 60 mm and with a minimum height of 50 mm.
- The hood draws in cooking vapors and evacuates them to the outdoors (evacuation
version) or returns them into the kitchen after passing through an active carbon filter
in which they are purified (“recycling” version).
- A front panel is fixed to the hood auvent for aesthetic continuity of the upper kitchen
units.
- Important: on delivery, the hood is equipped to operate in the “outdoors evacuation”
version.
- For use in the recycling version, install the active carbon kit reference AH 4020 F1
that you can order from your Fitter.
Important Recommendations
- In a kitchen heated with an appliance connected to a chimney (for example stove,
cooker, etc.), install the “recycling” version of the hood and check that there is
adequate room ventilation (fresh air).
- Preferably use the cooking areas at the back of your appliance.
- Operate the hood for a few minutes before starting cooking.
- Use low speed for simmering and dishes which produce little steam. (This speed
can also be used to ventilate the kitchen).
- Use the high extraction speed for normal use.
- When producing large quantities of steam during cooking, use the high extraction
speed and keep the hood operating after finishing cooking (about 15 or 0 minutes).
or your safety, and to respect our guarantee conditions:
- Do not connect the hood to smoke or extraction ducts already being used.
- Check that the mains voltage is the same as the values stated on the identification
plate inside the hood.
- Do not flambé food underneath the hood (the flames drawn in could damage the
filters or create a fire risk).
- Deep frying equipment under the appliance must be constantly monitored.
- Regularly clean the grease filters.

5
USAGE
The hood is fitted with a control box
behind the opening, containing
controlside (fig.1).
- Slide “L” is used to switch the lighting on
and off.
- Slide “M” is used to start or stop the fan,
confirmed by a power on indicator.
- Slide “V” is used to select the extraction
power from “1” to “ ”.
A contactor above the control box cuts
off the power as soon as the auvent is
fully closed, but functions previously
regulated with the slides are maintained.
MAINTENANCE
Before carrying out any work (cleaning -
changing filters - lighting), switch the
appliance off by pulling the plug out if you
can reach it, or by switching the circuit
breaker off.
Grease filter
The metal grease filter should be cleaned
every two months with normal usage and
can be cleaned in a dishwasher or by
hand using a mild detergent or liquid
soap.
Proceed as follows: (see fig.2 - fig.3)
- Open the auvent to the end stop.
- Remove the filters one at a time,
pushing the handle towards the rear
of the hood.
When replacing, ensure that the
handle faces outwards.
NOTE: new grease filters can be
obtained from your dealer.
Active carbon filters
(on appliance used in recycling version).
- Air drawn in also passes through the active carbon filter designed to eliminate cooking
odors.
- This filter cannot be cleaned, and therefore must be replaced at a frequency which
depends on the frequency of use (about twice per year).
106_01FA
1
2
106_0 FA
3

6
- Each filter is supplied with installation instructions.
Panelwork
Use lukewarm water only, to which a non-aggressive cleaning liquid is added. Do
not use abrasive or aggressive products, or products containing alcohol.
Lighting
- Lighting is provided by two 40 W bulbs.
- To replace them, remove the grease filters
as described in the “Grease filter” section
(fig. 4) to gain access to the bulbs.
- Replace the defective bulb or bulbs with
identical models and replace the grease
filters.
In case of problems
If you request assistance from your After Sales Service, you should inform them of
the characteristics stated on the identification plate close to the motor in your hood
(model - type - serial number).
OR THE INSTALLER
As the specialist, only you are competent to install and connect appliances.
This is why our guarantee is applicable exclusively and soley to appliances which
have been installed and connected by yourself, in accordance with the requirements
of ordinances in force. You will be responsible if this condition is not respected.
INSTALLATION
- The hood must always be fitted above the center of the cooker hob.
- The minimum distance between the top of the cooker hob and the bottom of the
hood shall be 650 mm.
- If your cooking appliance has a cover, check that it can be lifted without hindrance.
Assembly
- All accessories necessary for installation are supplied with the appliance.
- Use the template to position the support lug wall attachment holes and drill the holes
for the plugs (top edge of the hood aligned with the top of adjacent furniture).
- Attach the support lugs with appropiate screws.
Hood preparation
- Before starting wall mounting, the depth of the hood has to be adjusted to match the
depth of adjacent furniture.
4

7
- The hood depth can be adjusted between 27
and 6 cm.
Depth adjustment:
1 - Measure the body depth of the furniture
between which the hood is to be installed.
2 - Loosen the hexagonal bolts for the
adjustment of the upper suspension hooks
(fig. 8), pull the hooks to the correct
dimension and retighten the bolts.
- Loosen the lower spacer plate support bolts (fig. 9), pull it to the right dimension and
retighten the bolts. This square spacer plate with built in unequal ribs can be reversed
depending on the required depth.
Auvent preparation
- This hood must be fitted with a facade similar
to that for the furniture in the kitchen and fixed
to the auvent (facade supplied by the furniture
installer).
1 - Fully open the auvent and press the locking
key at the front left inside (fig. 7) to completely
remove theauvent.
2 - Drill the starter holes inside the facade using
the drilling template provided for this purpose.
- Place the auvent on the panel aligning the holes and screw in using the screws
provided. Do not put it back on the hood before installation on the wall.
Wall mounting
- Attach the hood by its suspension hooks to
the support lugs attached to the wall.
- To prevent accidental separation, drill and
attach the two safety brackets (supplied
with the appliance) to the wall so that they
bear on the suspension hooks.
- If necessary, adjust the alignment with the
adjacent furniture using the suspension
hook adjustment bolts (fig. 8).
Additional attachment to adjacent furniture
- Remove the filter support grillage and use the holes visible in the side walls to attach
to adjacent furniture. (The template supplied can be used before wall mounting).
8
9
7

8
Installing the evacuation duct
- Depending on the choice of evacuation ducts, install the 100 or 120 mm Ø duct
which attaches to the rear box by a bayonet system.
Connection
There is an adjustment lever inside the
hood (fig. 4) for selecting “evacuation” or
“recycling” (accessible after removing the
grease filters).
- Lever down - recycling (air outlet by front
upper louvers).
- Lever up - evacuation (outlet through rear
duct). These positions must be respected
in accordance with the selected use.
Connection to an individual or collective duct
- Connect the hood to an individual or collective
duct (unused flue) using pipes and connection
pieces made of uninflammable material.
- When the evacuation version hood is used, it
must not hinder existing ventilation or extraction,
and must be in accordance with Unified Technical
Document
DTU n° 61-1.
- Connection fittings must be made in accordance
with standard practice and respect safety
conditions, and under no circumstances shall the
evacuation duct discharge into the attic.
- Flues used as smoke ducts shall not be used.
EVACUATION DIRECTLY OUTDOORS
- In this case, it is recommended that the telescopic suction cup reference AH 4009
F1 with built in non-return valve be used (fig. 5).
- This square suction cup was specially designed for
hoods and can be built into any outside wall between
2 and 4 cm thick.
- Outside shutters prevent wind and rain from entering
and a raised edge (water spray) on the lower edge
prevents dirtying the facade.
- The built in non-return valve prevents return of cold
air into the kitchen during winter.
or wall drilling, see (fig. 6)
Special instructions provided with the suction cup
give all necessary additional information.
4
5
6

9
EVACUATION BY RECYCLING
- Put the adjustment lever to the recycling position (down) and after installing the
active carbon filter (as described in the installation part of these instructions and in
accordance with the instructions attached to the recycling kit) the recycled air is
discharged through the louvers at the top of the hood facade.
- In this case the hood must be drawn fully down to completely free the facade louvers.
Replacement of the auvent (panel and facade assembled)
- Lift the auvent by its lower part and insert the two upper guide-slides in their respective
housings.
- Pivot the auvent downwards inserting the two lower guide-slides and tilt the auvent
until it closes.
- Reopen the auvent to make sure that it operates correctly and to check the presence
of the stop at full opening.
- Depending on the weight of the facade, the friction resistance of the auvent may be
adjusted from the inside by means of screws located at the front corners of the
appliance (fig. 10).
- If necessary, make a final alignment with the adjacent furniture by adjusting the
auvent screws supporting the facade.
106_10FA
10

10
ELECTRICAL CONNECTION
- Connect the appliance cord to a 10/16 A standard grounded power outlet (2 pins +
earthing pin), preferably located above the hood.
- If the power outlet is not permanently accessible, a -pole switch will have to be
provided in the installation with a minimum contact opening of mm.
- The installation shall comply with standard NF C 15.100.
TECHNICAL DATA
Power supply voltage 230 V - 50 Hz
Total connection power 350 W
Motor 2 x 135 W
Lighting 2 x 40 W
Number of speeds 3
Evacuation duct diameter 100 or 120 mm
Hood width 598 mm
Hood depth 270/360 mm
Hood height 350 mm
This hood complies with EEC directives 76.889 and 82.499 related to
radioelectric disturbances (ordinance dated August 19th 1985 published in
Official journal date September 1st 1985)