ROBLON FL 500 XT B User manual

FL 500 XT B
LED light generators
for use with fibre optic lighting User manual
Mounting and installation instructions
Item no.: 0121 0211 FL 500 XT B Ø9 3000K
[phone] 15.04.2015

Contents
1 Introduction
2 Product overview
3 Technical data
4 Installation
5 Surface-mounting
6 Installing in closed compartments
7 Spare parts
8 Troubleshooting
1 Introduction
Roblon FL 500 light generators are designed for use.
outdoors.
with glass or PMMA fibre.
in cabinets or showcases, either in closed or semi closed compartments.
Follow the installation instructions correctly in order to ensure
safeoperation.
enhanced functionality.
extended lifetime for components.
uninterruptedillumination.

2 Product overview
FL 500 XT B light generator
User manual

3 Technical data
Light port Ø9 mm
Fibre type PMMA / Glass
Total power consumption 5.4 W
Supply voltage 200-240 V / 50-60 Hz
Applied LED Lumileds
Light source lifetime 25,000 hours
CCT (nominal) 3,000 K
CRI8(Ra) typical value 90
Protection rating IP 65
Driver type Electronic
Driver lifetime 25,000 hours
Dimmable Y e s
Thermal protection Integrated auto
Cooling system Natural convection
Noise level N/a
Ambient temperature -20°Cto 40°C
Material Aluminium
Dimensions (Lx Hx W) 164 x 67 x 63 mm
Weight 600 g.
Safety CE, F

4 Installation
1. Remove the plug on the end of the light generator.
2. Insert the common end fully in the light port.
3. Tighten the screw on the light port.
4. Mount the plug again.
Ensure all installation and ventilation requirements are met and connect
the supply cord to the mains.
1. 2.
3. 4.

5 Surface-mounting
1. Attach to surface using two screws (not supplied) in the baseplate holes.
6 Installing in closed compartments
Requirements:
Enough space to allow natural heat transmission through surfaces.
Surfaces should not be insulated.
Air volume per light generator minimum 0.03 m³.
Ventilation holes per light generator with min. 20 cm² air inlet and min. 20
cm² air outlet.
Inlet and outlet ventilation holes opposite each other.
Max. ambient temperature 40ºC. (Measuring temperature: see
‘Troubleshooting’).
84 mm

Image Item no.
Driver Sunpower 18 WDriver 1100 3063
7 Spare parts
Problem Trace the problem Solution
No light Is the power on? Turn the power on
Is the power cord
connected properly Connect the power cord properly
Is the light generator too
hot*? Check it is installed according to the
instructions.
Let it cool for 10 minutes.
Try again.
Light switches on and off Is the light generator too
hot*? Check it is installed according to the
instructions.
Let it cool for 10 minutes.
Try again.
Is the LED old Replace the LED
Light output has
diminished Is the light generator too hot*? Check it is installed according to the
instructions.
Let it cool for 10 minutes.
Try again.
Is the harness common
end dirty? Clean harness common end with a damp cloth.
Dry with lint-free cloth
*Ambient temperature: max 45°.Measured 50 mm from light generator.
Surface temperature: max. 73°C. Measured 15 mm from edge on top og light generator when it has been running for min. 1 hour.
8 Troubleshooting

Roblon Lighting Tel: [phone]
Nordhavnsvej 1 Fax: [phone]
9900 Frederikshavn [e-mail]
Denmark www.roblon.com
Roblon accepts no responsibility for possible errors in printed and electronic material. Roblon reserves the right to alter or discontinue products
without notice. © 2012, Roblon A/S.