Robobo RBE-X User manual

1
Quick start guide - Guía rápida

The next generation of educational

4
5
5
5
5
8
9
9
11
11
11
12
12
13
13
13
13
Index:
Robobo base user guide
Instruction icons
Copyright
Robobo base elements
Battery charge
Smartphone insertion in the Robobo base
Switching the Robobo base on and off
Security information
Specific Robobo base warnings
Electrical warnings
Battery warnings
General warnings
Correct disposal of this product
Declaration of Conformity
Manufacturer
Model
Index

5
EN
Robobo base user guide:
This robotic base offers entertainment services under the high standards and
technological experience of Manufactura de Ingenios Tecnológicos S.L.
The content may differ from the final product or software provided by the service
providers, and it is subject to change without notice.
The items that come with the robotic base and any available accessories may vary by
region or service provider.
The supplied items are designed only for this robotic base and may not be compatible
with others.
Instruction icons:
Warning: Situations that may cause injury to you or others.
Caution: Situations that may cause damage to the robotic base or other
equipment.
Note: Suggestions for use or additional information.
Copyright:
Copyright© 2018 Manufactura de Ingenios Tecnológicos S.L. This guide is protected by
international copyright laws.
No part of this guide may be reproduced, distributed, translated or transmitted in any
form or by any means, electronic or mechanical, including photocopying, recording or
storage in any information storage and retrieval system, without prior permission
provided by Manufactura de Ingenios Tecnológicos S.L.
Robotic base elements:
The robotic base contains the following basic elements, shown in the following
images:
• 2 wheel drives
• 1 Pan-Tilt unit, where the Smartphone is attached
• 5 frontal leds
• 2 rear leds
• 5 front infrared sensors
• 3 rear infrared sensors
• 1 micro USB connector (type B)
• 1 power button

The LEDs are illuminated depending on the base state. Their meaning can be checked
in user-guide.theroboboproject.com
The images may not exactly match the original model of the Robobo base. The
images are for guidance only.
Quick start guide

6
2
2
5
1
34
3
6
Robotic base elements:
1. Front leds
2. Wheel
3. Led
4. Power button
5. USB connector
6. Pan-Tilt unit
7. Infrared sensors
Quick start guide
EN

7
7 7 7 77 7 77
Quick start guide
EN

8
Battery charge:
Before using the robotic base for the first time, or if you have not used it for a long
time, the battery should be charged.
To do this, connect the micro USB connector (type B) to the multifunction plug or
charging port of the robotic base (see figure below), and then connect the USB end
(type A) to an USB current adapter (maximum 2A).
To visualize the charge voltage of the battery it is necessary to connect a
Smartphone to the robotic base and follow the instructions shown in
user-guide.theroboboproject.com
If you connect the cable incorrectly, it could cause serious damage to the base.
The warranty does not cover any damage caused by misuse.
After fully charging the robotic base, disconnect it from the power supply. First
disconnect the micro USB cable from the base, and then from the electrical outlet.
Quick start guide
EN

9
Smartphone insertion in the Robobo base:
To attach the smartphone to the Robobo base holder, you must insert it softly
between the two levers of the holder, separating them with your fingers if necessary
(*), and slide it down until it is fixed in its lower part.
(*) Supported dimensions are between 160x78x9.5 mm and 134x67x6.5 mm
approximately depending on the specific smartphone's geometry.
Switching the Robobo base on and off:
To turn the robotic base on, place it on a flat surface free of obstacles. Press the
button located on the back, as shown in the following image:
Power button
USB connector
Quick start guide
EN

10
During start up, the robotic base can perform a calibration movement of the pan-tilt
unit, which will rotate around its axis as indicated in the following image. Do not
obstruct or touch the pan-tilt unit until this movement is completed.
Once the pan-tilt calibration movement has been completed, the robotic base will be
ready for use.
Information on how to connect the Smartphone to the base and on how to use both
can be found at user-guide.theroboboproject.com.
Once you have finished using Robobo, remember to turn off the robotic base by
pressing the on/off button again. This will increase the duration of both the battery
and the base itself.
Quick start guide
Pan Axis
Tilt Axis
EN

11
Security information:
This section contains information on security. In order to avoid injury to yourself and
others, or damage to the robotic base, read the safety information before using this
product.
In case of not complying with these safety regulations and warnings, the user could
suffer serious injuries.
Specific Robobo warnings:
Robobo is not indicated for children under 8 years old.
It must be used under the supervision of an adult.
Choking hazard.
This device contains small parts that could cause asphyxia in the case of being
ingested by a child. The packaging is not part of the robotic base, do not leave it within
reach of children. Keep it away from children under 3 years old.
The use of the robotic base may not be allowed in public places.
Check that its use is allowed in the place where it will be used.
It is recommended to use Robobo indoors or in clean and low exposed outdoor
environments.
Subjecting the robotic base to dust, sand, water, sun or other elements present
outdoor can damage it irreversibly.
Do not allow the robotic base to fall or subject it to strong impacts.
The base may be damaged or malfunction.
If it bends or deforms, the robotic base may be damaged and its parts may
malfunction.
The use of the robotic base to perform movements on a table or on any other raised
surface that lacks protections at its edges at is edges is not recommended to prevent it
from falling off. In case it is used this way, extreme precautions should be taken so
that the robotic base cannot fall off from any of the edges of the surface.
Any damage suffered by the Smartphone coupled to the robotic base due to
improper use will not be the responsibility of Manufactura de Ingenios
Tecnológicos S.L.
Avoid, therefore, excessive speeds, shocks and the use in heights or over irregular
surfaces that may cause falls that damage the Smartphone.
Do not use the robotic base if it is broken.
Take the base to Manufactura de Ingenios Tecnológicos S.L. service center for its
repair.
If you notice that the robotic base emits odd smells or sounds, or if you see smoke
or liquids coming out of the robotic base, stop using it immediately and take it to
Manufactura de Ingenios Tecnológicos S.L. service center.
If you do not do it, it could cause a fire or an explosion.
Do not disassemble, modify or repair the robotic base.
Any change or modification to the robotic base may void the manufacturer's warranty.
If you need to repair the robotic base and take it to a Manufactura de Ingenios
Tecnológicos S.L. official service center.
Do not disassemble or puncture the battery, this may cause an explosion or fire.
Electrical warnings:
Do not use damaged power cords or connectors or loose plugs.
Unsafe connections can cause an electric shock or fire.
Do not touch the power cord with wet hands or pull the cord to disconnect it.
Doing this may cause electrocution.
Do not bend or damage the power cord.
Doing so could cause an electric shock or fire.
Do not use the robotic base while it is charging or touch it with wet hands.
Doing so could cause an electric shock.
Quick start guide
EN

12
Do not short-circuit the robotic base.
Doing so may cause an electric shock or fire, or the battery may malfunction or
explode.
Do not use the robotic base outdoors during a lightning storm.
Doing so may cause an electric shock, or the robotic base may not work properly.
Do not use the robotic base in a hospital, on an airplane or in a car that could suffer
interference caused by radiofrequency.
If possible, avoid using the robotic base at a distance of less than 15 cm from a
pacemaker, as it may interfere with it.
To minimize possible interference with a pacemaker, use the robotic base only on the
opposite side of the body from the position of the pacemaker.
If you use medical equipment, contact the manufacturer of the equipment before
using the robotic base, in order to determine if the equipment will be affected by the
radiofrequency emitted by the robotic base.
If electronic devices are used in an airplane, they can interfere with electronic flight
instruments.
Do not keep the robotic base near magnetic fields.
It may start to malfunction and the battery may discharge.
Battery warnings:
Use batteries, cables, accessories and supplies approved by the manufacturer.
Use only batteries approved by Manufactura de Ingenios Tecnológicos S.L., specifically
designed for the robotic base. Unsupported batteries and connectors can cause
serious physical injury or damage to the base.
Manufactura de Ingenios Tecnológicos S.L. is not responsible for the user's safety in
cases where accessories or supplies that are not approved by the brand are used.
Guarantee maximum battery life.
Avoid charging the base for more than a week, since overcharging can shorten battery
life.
Over time, the unused robotic base is discharged and it is necessary to recharge it for
use.
Disconnect the robotic base from the power sources when not in use.
Follow all instructions in this guide to ensure the longest possible life of the base and
battery. Damage or malfunction caused by failure to comply with these warnings and
instructions could void the manufacturer's warranty.
Over time, the robotic base can wear out. Some parts and repairs are covered by the
warranty within the period of validity, however, damage or deterioration caused by
the use of non-approved accessories do not have coverage.
Do not handle damaged lithium ion batteries or leaking batteries.
To safely dispose of the Lithium-ion battery contact an authorized service center.
General warnings:
Keep the robotic base dry.
Moisture and liquids can damage electronic parts or circuits of the robotic base.
Do not turn on the robotic base if it is wet. If it is already on, turn it off.
Next, dry the robotic base with a soft towel or cloth and take it to the service center.
Do not store the robotic base in hot or cold areas.
It is recommended to use it in temperatures between 5° C and 35° C
Consider the following information when cleaning the robotic base
Use a towel or a soft, dry cloth to clean the robotic base.
Do not use chemicals or detergents. Doing so may cause discoloration or corrosion on
the outside of the robotic base, or it may cause an electric shock or fire.
Do not use it for any purpose other than that for which it was designed.
The robotic base may not work correctly.
Quick start guide
EN

13
Correct disposal of this product:
(Waste electrical and electronic equipment)
(Applies in countries with separate collection systems)
The presence of this symbol on the product, accessories or accompanying information
material indicates that neither the product nor its electronic accessories (such as the
USB cable) should be disposed together with other household waste.
To avoid possible damage to the environment or human health from the uncontrolled
disposal of waste, separate these products from other types of waste and recycle them
correctly. This way, the sustainable reuse of material resources is promoted.
Private users can contact the establishment where they purchased the product or the
relevant local authorities to find out how and where they can take it to be subjected to
an ecological and safe recycling.
Commercial users can contact their supplier and check the conditions of the purchase
contract. This product and its electronic accessories must not be disposed of together
with other commercial waste.
Declaration of Conformity:
Manufactura de Ingenios Tecnológicos S.L. declares, under its responsibility, that this
device complies with the provisions of Directive 99/05/EC of the European Parliament
and of the Council of March 9, 1999, transposed into Spanish legislation by Royal
Decree 1890/2000, of November 20.
Printed in UE
Manufacturer:
Manufactura de Ingenios Tecnológicos S.L.
Edificio Servicios Centrales de Investigación s/n
Campus de Elviña, 15071, A Coruña
[e-mail]
Spain
Model:
RBE-X
English. 03/2018. Rev. 1.0
Quick start guide
EN
http://www.theroboboproject.com/

14
www.theroboboproject.com