Robomow RK4000 Installation manual

ADDITIONAL INFORMATION
MÁS INFORMACIÓN
INFORMATIONS COMPLÉMENTAIRES
Original user instructions

3
ADDITIONAL INFORMATION

4
2 sec
Safety first
Maintenance and Cleaning
1. Switch off the robot
2. Remove the disabling device before doing any
maintenance
EN EN

5
Blade Replacement
Periodically inspect the blades and replace them if damaged.
It is recommended to replace the blades per the table below.
Always replace all 4 blades, including the screws.
< 1/8 acre Every 8 - 10 weeks
1/8 acre - 1/4 acre Every 6 - 8 weeks
> 1/4 acre Every 4 - 6 weeks
Watch the video
EN EN

6
Cleaning
The RK wheels and deck are self-cleaning. Accumulated grass, soil and debris
will disperse when dry conditions return.
Every 1-2 weeks, clean the robot underneath.
Remove debris
from the wheels
EN EN

7
Remove debris between
the guard wires
Use a soft brush to remove
debris from the mowing deck
EN EN

8
During longer periods of increased wet conditions, mud and mulch can accumulate on wheels.
It is recommended to attach the wheel cleaners accessories to assist in removing debris in
these conditions.
Insert each wheel cleaner
into its respective slot
Left
wheel
Right
wheel
L
L
R
STOP
STOP
R
Install the wheel cleaners
Watch the video
EN EN

9
Press wheel cleaner firmly into
slot until it is securely in place
EN EN

10
Technical Spec RK1000 RK2000
Model number 22AKFAFA737 22AKHAFA737
Recommended lawn size [acre] Up to 1/4 acre Up to 1/2 acre
Cutting width [inch] 8.25” 8.25”
Cutting height [inch] 0.8” - 4.0” 0.8” - 4.0”
Sub-zones 4 4
Separated zones
Wire [ft.] 740 1000
Number of pegs 300 400
Mowing motors DC Brushless DC Brushless
Drive motors DC Brushless DC Brushless
Max. incline mowing area 45% (24°) 45% (24°)
Max. incline wire on slope 20% (11°) 20% (11°)
Sound pressure level Lpa dB(A) (K=3) 50 50
Measured sound power level Lwa, dB(A) 61 61
Guaranteed sound power level Lwa, dB(A) 64 64
Mowing time [min] 40-50 80-90
Charging time [min] 60-120 60-120
Battery type 18,15V Li-Ion 18,15V Li-Ion
Battery capacity spec [Ah] 4.9 4.9
Power consumption [kWh/month] 47.3
Anti-theft
Bluetooth (BLE)
GSM module
Near Wire Following (MBLE)
Max altitude [ft.] 10,000 ft 10,000 ft
Warranty 3 years 3 years
Mowing time and lawn size based on ideal mowing conditions.
EN EN

11
Technical Spec RK3000 RK4000
Model number 22AKJAFA737 22AKLAFA737
Recommended lawn size [acre] Up to 3/4 acre Up to 1 acre
Cutting width [inch] 16.5” 16.5”
Cutting height [inch] 0.8” - 4.0” 0.8” - 4.0”
Sub-zones 4 4
Separated zones
Wire [ft.] 1300 1500
Number of pegs 500 550
Mowing motors DC Brushless DC Brushless
Drive motors DC Brushless DC Brushless
Max. incline mowing area 45% (24°) 45% (24°)
Max. incline wire on slope 20% (11°) 20% (11°)
Sound pressure level Lpa dB(A) (K=3) 53 53
Measured sound power level Lwa, dB(A) 64 64
Guaranteed sound power level Lwa, dB(A) 65 65
Mowing time [min] 80-90 110-120
Charging time [min] 60-80 90-110
Battery type 18,15V Li-Ion 18,15V Li-Ion
Battery capacity spec [Ah] 9.6 9.6
Power consumption [kWh/month] 11.5 11.5
Anti-theft
Bluetooth (BLE)
GSM module
Near Wire Following (MBLE)
Max altitude [ft.] 10,000 ft 10,000 ft
Warranty 3 years 3 years
Mowing time and lawn size based on ideal mowing conditions.
EN EN

12
FCC/ISED Regulatory notices
General
As an integrated product, the RK models are fully compliant with the grants of the FCC
Equipment Authorization and the ISED Technical Acceptance Certificates issued for the built-
in modular approved radio modules as follows:
Description Module name US/FCC ID Canada/IC ID Grantee
CATM / NBIoT
module
ME310G1-WW RI7ME310G1WW 5131A-ME310G1WW Telit Communications
S.p.A
BT Light Energy
V5.0 module
BL652-SA SQGBL652 3147A-BL652 Laird Technologies
Note: The listed above radio modules may be limited to the specific product models.
Modification statement
MTD has not approved any changes or modifications to this device by the user. Any changes
or modifications could void the user’s authority to operate the equipment.
Interference statement
This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Wireless notice
This device complies with FCC/ISED radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS‐102
of the ISED radio frequency (RF) Exposure rules. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter. The antenna should be
installed and operated with minimum distance of 20 cm between the radiator and your body.
EN EN

13
Part Number Part Description
725-18190 Battery for RK1000/2000
725-17288 Battery for RK3000/4000
122-100-619 Blade Kit
742-05538 Single blade
725-17045 Power supply for RK1000/2000 US
725-17046 Power supply for RK3000/4000 US
Replacement parts
FCC Class B digital device notice
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to
the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
CAN ICES-3 (B) / NMB-3 (B)
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de
classe B est conforme à la norme canadienne ICES-003.
EN EN

14
Storage mode
The Storage mode is intended for winter or other long periods where mowing is not needed,
and it minimizes power consumption.
At the end of the mowing season, it is recommended to turn the Storage mode on, through the
'Settings' menu. Storage mode will be automatically activated on the base station too.
To activate Storage mode:
1) Place mower in the base station
2)Turn ON Storage mode setting on mower
Once activated and the mower is fully charged, it will automatically enter sleep mode
to reduce power consumption. It disables scheduled departures and disconnects all
communication devices (Bluetooth /GSM).
To deactivate Storage mode:
1) Turn OFF Storage mode setting on mower
2)Disconnect base station power from mains outlet for 20 sec.
3)Re-connect base station power
Once the mower and base station are awake, mowing will resume per the scheduled
departures.
EN EN

MÁS INFORMACIÓN

16
2 segundos
Seguridad ante todo
Mantenimiento y limpieza
1. Apagar el robot
2. Antes de cualquier trabajo de mantenimiento, retirar
siempre el dispositivo de desactivación
ES ES

17
Cambio de cuchillas
Inspeccionar periódicamente las cuchillas y, si están dañadas, cambiarlas.
Se recomienda cambiar las cuchillas según la tabla siguiente.
Siempre cambiar las 4 cuchillas, incluidos los tornillos.
< 1/8 de acre Cada 8 a 10 semanas
De 1/8 a 1/4 de acre Cada 6 a 8 semanas
> 1/4 de acre Cada 4 a 6 semanas
Ver el vídeo
ES ES

18
Limpieza
Las ruedas y la plataforma de la RK son autolimpiables. La hierba, la tierra
y los restos que se hayan acumulado se dispersarán cuando vuelvan las
condiciones de sequedad.
Cada 1 o 2 semanas, limpiar el robot por debajo.
Eliminar los
residuos de las
ruedas
ES ES

19
Eliminar los residuos
entre los cables de
protección
Para eliminar los residuos de
la plataforma de corte, utilice
un cepillo suave
ES ES

20
Durante periodos prolongados de aumento de las condiciones de humedad, en las ruedas
podrían acumularse barro y mantillo. Se recomienda adjuntar los accesorios de limpieza de
ruedas para ayudar a eliminar los residuos en estas condiciones.
Inserte cada limpiador de ruedas
en su ranura respectiva
Rueda
izquierda
Rueda
derecha
Izq.
Izq.
Der.
STOP
STOP
Der.
Instalación de los limpiadores de ruedas
Ver el vídeo
ES ES