Robomow RL2000 Instruction Manual
Operating & Safety Manual
RL MODELS
WWW.ROBOMOW.COM / WWW.ROBOMOW.EU
DOC0100D
Everything you need to know about Robomow is in this manual.
The instructions are simple and user-friendly.
The manual is to be used for:
1. Robomow RL2000
2. Robomow RL555 and Robomow RL855
Most instructions in this manual are for ALL models.
Some parts are intended for specific models or specific configurations.
Model-specific paragraphs
All information by the “RL2000 Only” margin-line is for Robomow RL2000 only.
If your Robomow is NOT RL2000, please skip down to the end of this margined-line.
All information by the “RL555 RL855 Only” margin-line are for Robomow RL555 or RL855 only.
If your Robomow is NOT RL555 or RL855, please skip down to the end of this margined-line.
All information by the “RL855/555 Only. Non-base zone” margin-line is either for Robomow RL555/RL855 OR for
Robomow RL2000, when used in an area of the lawn controlled
by a Perimeter Switch (not Base Station controlled).
If you are using Robomow RL2000 in a Base Station controlled zone, please skip down
to the end of this margined-line.
All information with no special sign is relevant to ALL models of Robomow.
Model specific short text
Short text next to this sign
is relevant to Robomow RL2000 only.
Short text next to this sign
is relevant to Robomow RL555 or RL855 only.
No sign to
the left
Introduction - 1
Introduction
EU Declaration of Conformity
Manufacturer: F. Robotics Acquisitions Ltd.
Hatzabar St., Industrial Zone
P.O.Box 1412 Pardesiya,
42815 Israel
The products covered by this Declaration
24 Volt Battery operated Automatic Lawn Mower model RL2000 (with Base Station)
24 Volt Battery operated Automatic Lawn Mower model RL855/555 (with Perimeter Switch)
F. Robotics Acquisitions Ltd. declares under sole responsibility that the products identified above conforms with
the protection requirements of the EMC directive and with the principal elements of the safety objectives of the Low
Voltage Equipment directive, and that the following standards have been applied:
EMC-
EN 55014-1:2006 & EN 55014-2:1997 + A1:2001 (Robomow)
EN 55024:98 + A1:2001 + A2:2003 + EN 55022:1998 + A1:2000 + A2:2003 (Charging Station)
Electrical Safety-
BS EN 60335-1:2002 *AMD1 15172, 2002 *AMD2 15626, 2005 *AMD4 15051,
2004 *AMD5 15536, 2005 *AMD6 16671, 2007
BS EN 50338: 2006 AMD1 16778, 2006
Machinery Directive-
Essential Health and Safety
Risk Assessment EN 1050
Noise Directive-
To BS EN ISO 3744: 1995 and *ISO 11094: 1991. With reference to Outdoor noise directive 2000/14/EC:
Amended by directive 2005/88/EC and the corrigenda table 1. Article 12: Test code of Annex III Part B
Item 32.
Sound level
Measured sound power level: LwA = 76.6 dB
Guaranteed sound power level: LwA = 80 dB
EMF-
BS EN 50366: 2003 amd1 16426, 2006
EMC Competent Body All Others Directives Competent Body
QualiTech
30, Hasivim Street
P.O. Box 3083
Petah Tikva 49130
Israel
SGS UNITED KINGDOM LIMITED
Rossmore Business Park
ELLESMERE PORT
CH65 3EN South Wirral Cheshire
United Kingdom
The technical documentation kept by Mr. Dedy Gur, QA director.
Address: Hatzabar St., Industrial Zone P.O.Box 1412 Pardesiya, 42815 Israel.
I hereby declare that the above product conforms to the requirements as specified above.
Shai Abramson – Senior VP R&D
F. Robotics Acquisitions Ltd.
1 December 2009
Introduction - 2
Robomow RL555, RL855, RL2000
The products are manufactured by F. Robotics Acquisitions (Friendly Robotics).
CE approved.
© Friendly Robotics, 2010-A. All rights reserved. No part of this document may be photocopied, reproduced, electronically
transmitted or translated without the prior written consent of Friendly Robotics.
Product, product specifications and this document are subject to change without notice. All other trademarks are property of
their respective owners.
Welcome to the world of home robotics with the Friendly Robotics Robomow!
Thank you for purchasing our product. We know that you will enjoy the extra free time you will have while using Robomow to mow your
lawn. When set up and used properly, Robomow will operate safely on your lawn and provide you with a quality of cut matched by a
few mowers of any kind. You will be impressed with your lawn’s appearance and best of all, Robomow did it for you.
IMPORTANT!
The following pages contain important safety and operating instructions.
Please read and follow all instructions in this manual. Carefully read and
review all safety instructions, warnings and cautions contained in this manual.
Failure to read and follow these instructions, warnings and cautionary statements
may result in severe injury or death to persons and pets or damage to personal property.
Introduction - 3
Introduction
Warning Decal Definitions
These are the symbols on Robomow; Read them carefully before operating Robomow.
DANGER! Sharp rotating blades. Keep hands and feet away.
Serious injury can occur. Caution – Do not touch rotating blade(s)
CAUTION! Remove Power Pack before
attempting to lift the mower for any reason.
Safety alerts symbol – WARNING -1. this is a dangerous power tool. Use care when operating and follow all safety
instructions and warnings.
Read operator’s manual –2. Read user instructions before operating your Robomow
Hazard of Thrown or flying objects -3. Whole body exposure, take caution.
Keep a safe distance from the machine when operating4.
Keep people in particular children, pets and bystanders away from the area in which Robomow is being used.
Severing of toes or fingers - Rotary mower blade5.
Risk of injury from rotating cutting blade. Keep hands and feet away and do not attempt to lift Robomow from
this area.
Remove the disabling device before working on or lifting Robomow6. . Remove the Power Pack before working on or
lifting Robomow.
Do not ride on Robomow7. .
Do not dispose Robomowor any other part of it as unsorted
municipal waste – it should be collected separately.
This warning symbol will be found at several
points throughout the pages of this manual.
It is intended to highlight an important safety,
warning or cautionary message.
Please pay particular attention to these
areas and be sure you fully understand
the message before proceeding.
1 2 3 4 5 6 7
WARNING!
Introduction - 4
Robomow RL555, RL855, RL2000
Safety Warnings & Precautions
Use
Read this1. Operating and Safety Manual carefully and be familiar with the controls and the proper use of Robomow
before operating Robomow.
Never allow children or people unfamiliar with these instructions2. to use Robomow.
Never mow while people, especially children,3. or pets are nearby.
It is strongly recommended to use4. the CHILD GUARD or ANTI THEFT (4 PIN code) option in order to prevent operation
by children or others who are not familiar with Robomowoperation.
Never let Robomow5. operate without supervision.
The operator or user is responsible for6. accidents or hazards occurring to other people or their property.
Wear eyes protection and use gloves when installing the perimeter7. wire and driving the wire stakes/pegs. Firmly drive all
pegs in order to keep the wire from becoming a tripping hazard.
Make sure to layout and install the perimeter8. wire according to the instructions.
Periodically inspect the area mowed9. by Robomow, and remove stones, sticks, wires, bones and other objects. Objects
struck by the blades may be thrown and cause severe injuries to people.
In case of abnormal vibrations10. , stop the mower, remove the power pack and visually check for any damage of the blade or
mowing deck. Replace worn or damaged blades to preserve balance. If vibration continues, call for service.
Keep hands and feet away from the11. cutting blades and other moving parts.
Always remove the Power12. Pack before lifting the mower or attempting any adjustments. Do not to touch the blades
before the blades have come to a complete stop.
Never attempt to service or adjust13. the mower while it is in operation.
When programming the14. automatic departure times and days, do not leave the machine to operate unattended if you know
that there are pets, children or people in the vicinity.
Do not use Robomow15. for any purpose other than for which it is intended.
Do not operate Robomow16. if any safety feature or device is damaged or inoperable.
Never allow anyone to ride17. or sit on mower.
Warning! When there is a risk18. of a lightning storm, disconnect the perimeter wire from the Base Station/ Perimeter
Switch and the Power Supply 230V/120V plug from the mains socket.
Keep all guards, shields, safety19. devices, and sensors in place. Repair or replace damaged parts, including decals. Do not
operate Robomowif any parts are damaged or worn.
Never pick up or carry this20. appliance while the motors are running.
Transport21. - to safely move from or within the working area:
Use caution when lifting1. Robomow, it is heavy! Before lifting it, always take out the battery.
Use the Manual Controller to drive it from2. place to place.
In case of different height level or3. stairs, remove the Power Pack from the mower and carry the mower by the
carrying handle (See Introduction - 8).
Using Manual Controller
Mow only in daylight or in a22. good artificial light and avoid operating in wet grass;
Do23. not operate Robomowwhen barefoot or wearing open sandals. Always wear substantial footwear and long trousers;
Always be sure of24. your footing on slopes;
Use extreme caution when reversing the25. appliance towards you;
Always switch on the motor according to26. instructions with feet well away from the blades;
Do not27. mow manually in slope greater than 15 degrees or where a firm footing is not possible;
Maintenance
Always remove28. the Power Pack from the Robomowin the following cases: before clearing blockage/ checking/ cleaning/
working on Robomowor replacing the blades.
Always remove the Power Pack29. from the Robomowafter striking a foreign object or whenever Robomowstarts vibrat-
ing abnormally.
Use heavy gloves when inspecting or servicing30. the blades.
Do not open or mutilate the power pack.31. Released electrolyte is corrosive and may damage the eyes or skin.
Introduction - 5
Introduction
Replace worn or damaged parts for safety;32.
Use only33. the original equipment and accessories. It is not permitted to modify the original design of Robomow. All modi-
fications are made at your own risk.
Ensure that batteries are charged using34. the correct charger recommended by the manufacturer. Incorrect use may result
in electric shock, overheating or leakage of corrosive liquid from the battery;
Maintenance/ Servicing of Robomow35. should be according to manufacturer instructions;
A spark may be created when36. inserting the power pack or fuse to the robot. Therefore it is forbidden to perform these tasks
close to flammable materials. It is also forbidden to use spray or any other cleaning materials for cleaning electronic con-
tacts, due to this risk of inflammation when inserting the power pack or fuse.
Product end of use
Robomow and its accessories should be collected separately at the end of their life to prevent waste electrical and elec-37.
tronic equipment from ending up in landfill sites, to promote the reuse, treatment and recovery of electrical and electronic
equipment in purpose to preserve, protect and improve the quality of the environment, protect human health and utilize
natural resources prudently and rationally.
Do not dispose Robomow or any other part of it (including the Charger, Base Station and Perimeter Switch) as unsorted38.
municipal waste – it should be collected separately.
Ask your local distributor/dealer about return and collection systems available.39.
Do not dispose of the battery pack in a fire and do not place used batteries in your household trash. The battery must be40.
collected, recycled, or disposed of in an environmentally sound manner.
Robomow®- Safety Features
Child Guard / Safety Guard1.
This menu option offers a safety feature to help prevent children or others not familiar with the safe operation of the mower to
operate it freely.
Lift Sensor2.
There is a sensor located on the front of the mower. In the event the mower is raised from its resting position on the ground
during blade operation, the blades will stop rotating immediately (< 1 second).
Sensor Equipped Bumpers3.
The front and rear bumpers are equipped with contacts that will activate when the mower strikes a solid, fixed object. When the
bumper sensor is activated, the mower stops the blades immediately and reverses itself away from the obstacle.
Emergency Stop Switch4.
The STOP button is located on the Manual Controller. Pressing this button at any time during operation will stop all mower
movement and the rotation of the blades immediately.
Two-Step Operator Presence Control5.
While in manual mode, it requires two independent finger actions in order to engage the mower blades. Once engaged, the
mower blade button must remain depressed to continue blade operation. Once released, the two-step engagement process
must be repeated.
Sealed Batteries6.
The batteries that operate the Robomow are completely sealed and will not leak any type of fluids, regardless of position.
Perimeter Switch and Perimeter Wire7.
The Robomow cannot operate without a perimeter wire installed and activated through the Base Station/ Perimeter Switch. In
the event the Perimeter Switch is turned off or otherwise fails to function, the Robomow will stop operating.
Automatic departure warning alert8.
When the mower is scheduled to depart the Base Station automatically per a scheduled time, a warning sound and the operat-
ing lamp will activate 5 minutes prior to departure. This is a warning notification to clear and inspect the area.
Introduction - 6
Robomow RL555, RL855, RL2000
How It Works
A one-time setup is required before operating Robomow; a small wire, called the perimeter wire, is placed around•
the edge of the lawn and any other areas where you do not want the mower to enter.
Small pegs are supplied with Robomow and they are used to fasten and hold the perimeter wire to the ground,•
below grass level; the wire will soon disappear under the growth of new grass and will not visible.
The Base Station is placed along the perimeter wire and it has two main functions:•
- To generate a small signal along the perimeter wire (very low voltage);
- To charge Robomow batteries.
After completing the one-time set-up of wire around the lawn including the Base Station set the weekly program•
and forgets about mowing for the entire season!
Robomow will leave the Base Station on the day and time scheduled in the automatic weekly program; it will mow•
the lawn and will drive back for charging in the Base Station to be ready for the next operation.
When Robomow leaves the Base Station it automatically starts the signal carried through the Base Station; the•
signal creates a virtual wall, which is visible only to the Robomow, keeping it inside the lawn preventing it to cross
over area where you do not want it to enter.
Robomow detects the
signal and changes
direction as it reaches
the wire
Perimeter Wire as a
virtual wall, visible only
to Robomow
Tree with hole or flowers around; require
placing a wire around it
Base Station generates a signal
along the wire and is used to
charge Robomow batteries
Trees large enough to allow
Robomow to bump into; do not
require a perimeter wire around it
Introduction - 7
Introduction
What’s in the Boxes
1Robomow®9
Base Station wheel supports Used for sup-
porting Robomow drive wheels when entering
and departing the Base Station.
17 Wire connectors
Used for splicing wires (as needed).
2Power Pack 10
Screws x2
Used for assembling the Base Station wheel
supports to the Base Station.
18
Plot connector
Used for connecting the completed
perimeter wire set-up to the perimeter
switch/Base Station.
3Perimeter Wire
Used to create a virtual wall for your Robomow. 11 Extension cord (15meters low voltage
cable) 19
Screws x2
Used for assembling the Base Station
Cover to the Base.
4Pegs - Used for securing the wire to the ground. 12 Indoor Power Supply 20
Power Supply holder (+ screws and
dowels) Used for fixing the Power Sup-
ply to a wall.
5 Assembled Base Station. 13 Base Station Stakes - Used for securing the Base
Station to the ground. 21 Perimeter Switch
6
Base Station Cover
Used for recharging the Robomow Power Pack
and activates the perimeter wire.
14 Operating & Safety Manual 22
Perimeter Switch Stake - Used to
hold the perimeter switch vertical to the
ground.
7Base - Used for directing the Robomow to the
charging contacts. 15 DVD – Setup and Operation video. 23
Power Supply for Perimeter Switch
– Used for operating the perimeter
switch. Batteries available as an ac-
cessory
8
Charging Fence
Used for preventing the Robomow to climb on
the Base Station during operation.
16
RoboRuler
Used for setting the distance of the perimeter
wire from the lawn edge.
24 Power Supply
(for charging Robomow)
Introduction
Introduction 7
What’s in the Boxes
1
Robomow®9
Base Station wheel supports Used
for supporting Robomow drive
wheels when entering and departing
the Base Station.
17
Wire connectors
Used for splicing wires (as
needed).
2Power Pack 10
Screws x2
Used for assembling the Base
Station wheel supports to the Base
Station.
18
Plot connector
Used for connecting the completed
perimeter wire set-up to the
perimeter switch/Base Station.
3
Perimeter Wire
Used to create a virtual wall for your
Robomow.
11 Extension cord (15meters low
voltage cable) 19
Screws x2
Used for assembling the Base
Station Cover to the Base.
4Pegs - Used for securing the wire to the
ground. 12 Indoor Power Supply 20
Power Supply holder (+ screws
and dowels) Used for fixing the
Power Supply to a wall.
5 Assembled Base Station. 13 Base Station Stakes - Used for securing
the Base Station to the ground. 21 Perimeter Switch
6
Base Station Cover
Used for recharging the Robomow Power
Pack and activates the perimeter wire.
14 Operating & Safety Manual 22
Perimeter Switch Stake - Used to
hold the perimeter switch vertical to
the ground.
7Base - Used for directing the Robomow
to the charging contacts.
15 DVD –Setup and Operation video. 23
Power Supply for Perimeter
Switch –Used for operating the
perimeter switch. Batteries
available as an accessory
8
Charging Fence
Used for preventing the Robomow to
climb on the Base Station during
operation.
16
RoboRuler
Used for setting the distance of the
perimeter wire from the lawn edge.
24
Power Supply
(for charging Robomow)
2
1
34
5
6
7
8
9
11 12
13
15
10 19
17
18
20
RL2000 ONLY
14
21 22
23
24
16
RL555/855 ONLY
Operating & Safety Manual
RL MODELS
WWW.ROBOMOW.COM/ WWW.ROBOMOW.EU
DOC0100D
RL2000 ONLY
RL555/855 ONLY
Introduction - 8
Robomow RL555, RL855, RL2000
Name of the Parts
Robomow®
1. Charging Contact Pins
2. Carrying handle
3. Manual Controller
4. Operating Lamp
5. Power Pack
6. Bumpers with touch sensitive sensors
Manual Controller Panel
1. Manual blade engagement button
2. Manual drive speed control – fast/slow
3. Navigator button
4. GO button
5. Scroll arrows for menu selection
6. Stop button
7. Clear/cancel button
8. LCD display window
Base station
1. Cover
2. Base
3. Stakes (x5)
4. Drive wheels support
5. Screws (x2)
6. Fence
7. Screws (x2)
Perimeter Switch (Station)
1. ON/OFF button
2. Flashing light indicates the system is on
3. Indicates a disconnected/broken wire
4. Indicates poor splicing of perimeter wires
or perimeter wire, which is too long
i
Table Of Contents
Chapter 1 Planning..................................................................................................... 1-1
1.1 Determine Base Station location ..................................................................... 1-1
1.2 Planning the Perimeter Wire’s layout............................................................... 1-2
Chapter 2 Base Station and Perimeter Wire Setup..................................................2-1
2.1 Perimeter Wire Setup .........................................................................................2-1
2.2 Special cases of Perimeter Wire setup.............................................................2-3
2.3 Fastening Perimeter Wire to the Ground..........................................................2-5
2.4 Back at Base Station – Completing the Perimeter Wire setup.......................2-6
2.5 Assembling the Base Station ............................................................................2-6
2.6 Placing Base Station ..........................................................................................2-9
2.7 Testing Base Station setup..............................................................................2-10
2.8 Setup in Non-Base Zones ................................................................................2-10
2.9 Perimeter Switch placing options:..................................................................2-11
2.10 Laying Out the Perimeter Wire .......................................................................2-11
2.11 Completing and Testing the Setup .................................................................2-11
2.12 At the Perimeter Switch’s location: ................................................................2-12
Chapter 3 Preparing Robomow................................................................................. 3-1
3.1 Inserting Power Pack Fuse ...............................................................................3-1
3.2 Setting Country and first-time calibration........................................................3-1
3.3 Setting The Cutting Height And Ground Clearance ........................................3-2
3.4 Testing Base Station and Perimeter Wire charging position .......................3-4
3.5 Test the Perimeter Wire Position for Edge Mowing.........................................3-4
Chapter 4 The mowing process – automatic and manual operation..................... 4-1
4.1 For added safety:................................................................................................4-1
4.2 Driving Robomow – general instructions ........................................................4-1
4.3 Depart ..................................................................................................................4-1
4.4 Returning to Base Station .................................................................................4-2
4.5 Activating the Perimeter Switch (Non base-station zone) ..............................4-3
4.6 Positioning Robomow on the lawn. ..................................................................4-3
4.7 Edge Mowing (Non-Base Station Zone)............................................................4-4
4.8 Scanning (mowing) ............................................................................................4-4
4.9 To skip Edge Mowing .........................................................................................4-4
4.10 Completing the mowing (Non-Base Station Zone)..........................................4-5
4.11 Manual Mowing...................................................................................................4-6
ii
Robomow RL555, RL855, RL2000
Chapter 5 Setting the Weekly Program (RL2000 only)............................................ 5-1
5.1 Setting the weekly mowing program ................................................................5-1
5.2 Setting the current time .....................................................................................5-2
5.3 Canceling an active day.....................................................................................5-2
5.4 Weekly Program Display....................................................................................5-3
Chapter 6 Charging .................................................................................................... 6-1
6.1 Charging at the Base Station ...........................................................................6-1
6.2 Charging the Power Pack through an indoor power socket ........................6-2
6.3 Power Management and Charging Alerts.........................................................6-2
6.4 Off-season storage .............................................................................................6-3
Chapter 7 Setting Robomow and using Advanced Features ................................. 7-1
7.1 Manual User Options..........................................................................................7-1
7.2 Settings ...............................................................................................................7-1
7.3 Information..........................................................................................................7-7
7.4 Docking Options (Base Station only) ....................................................................7-7
Chapter 8 Troubleshooting ....................................................................................... 8-1
8.1 Text error-messages...........................................................................................8-1
8.2 Messaging ..........................................................................................................8-1
8.3 Other Problems...................................................................................................8-5
Chapter 9 Specifications............................................................................................ 9-1
Chapter 10 Maintenance and Storage.......................................................................10-1
10.1 Recommended Maintenance Schedule ..........................................................10-1
10.2 Maintenance of the Mouing Deck....................................................................10-1
10.3 Maintenance of the Blades ..............................................................................10-2
10.4 Maintenance of the Outer Housing .................................................................10-2
10.5 Maintenance of the Power Pack......................................................................10-3
10.6 Disposing the Old Battery Pack ......................................................................10-3
10.7 Splicing the Perimeter Wire.............................................................................10-3
10.8 Maintenance of the Base Station area............................................................10-4
10.9
Winter Storage f
...........................................................................................10-4
Chapter 11 Accessories............................................................................................. 11-1
Chapter 12 Tips for maintaining your lawn.............................................................. 12-1
Warranty Card
Chapter 1-1
Planning
PlanningChapter 1
Before starting the setup, please read this chapter fully and watch the setup
DVD. This will help you determine the best location for the Base Station
, for the perimeter wire layout, or for the perimeter switch.
Determine Base Station location1.1
Robomow’s Base Station is placed along the Perimeter Wire. This is where
the wire “loop” starts and ends. The Base Station has two main functions:
It generates a small signal along the perimeter wire (very low voltage),●
which serves as an “invisible wall” setting the lawn boundaries for
Robomow.
It charges Robomow’s batteries.●
After completing the one-time set-up of the Perimeter Wire and the Base Station,
a weekly program is set. That’s when Robomow does your mowing for the entire
season!
Robomow leaves the Base Station on the day and time scheduled in the automatic
weekly program. It mows the lawn and it returns to the Base Station for recharging.
First, you decide where the Base Station will be placed…
Inside the lawn area, along its outer edge.■
Or:
Outside the lawn area■
Consider the following in order to1.1.1
choose the best location:
If the lawn has more than one zone, set the base❍
station within the largest plot or zone.
Make the Base Station invisible to the street.❍
Prefer a shady spot.❍
This will extend battery lifetime
Place the Base Station on a relatively level ground.❍
Do NOT place it on a slope.❍
Place the Base Station at least 1 meter from corners.❍
Place the Base Station away from sprinkler heads.❍
Water or rain does not harm Robomow. However, we
recommend a distance from sprinklers for maximum protection.
If Base Station is to be located outside the lawn area1.1.2
External setup of the Base Station allows the Base Station to be located
outside the lawn area, close to its edge.
Consider the following in order to choose the best external
location:
Choose a place close to the lawn edge.❍
The passing between the lawn and the Base Station❍
should be smooth, with no height differences.
This will enable Robomow to follow the wire smoothly to its Base
Station.
The surface of the external area should be hard (e.g. a❍
sidewalk, firm ground). It should not be sandy or stony.
This will prevent Robomow from slipping or getting stuck.
Option A - Internal setup
(Inside the lawn along the outer edge)
Base
Zone
Base Zone
Base Station
Zone A
Base Station
Option B - External setup
(Outside the lawn)
Chapter 1-2
Robomow RL555, RL855, RL2000
Determine location of Power Supply1.1.3
The Base Station should be close enough (15 m/50 ft) to❍
a wall electrical socket (230V / 120V). The indoor Power
Supply unit will be connected to it.
Robomow’s 15 m (50 ft) low voltage cable connects❍
to the power supply unit. The length of the low voltage
cable must NOT be changed.
Select the right location for the power supply unit❍:
The power supply is suitable for indoor use only. Choose a
sheltered, dry, well ventilated spot.
It should NOT be exposed to direct sunlight or rain.
Planning the Perimeter Wire’s layout1.2
The Perimeter Wire functions as an “invisible wall” for Robomow. It sets
the boundaries of lawn zones and it surrounds specific areas where you
do not want Robomow to enter.
The Perimeter wire is held to the ground with small pegs, supplied with
Robomow. Soon after setting, the wire will become invisible under the
growth of new grass.
As soon as Robomow starts operating, it turns on a signal that runs along
the Perimeter Wire. This signal keeps Robomow within its working zones
and away from preset demarcated areas.
Is your lawn a single contiguous area?1.2.1
If grass areas are contiguous, Robomow
will automatically mow all zones tracking the
Perimeter Wire you set around the lawn.
Does your lawn have more than one zone?1.2.2
If your lawn areas are separated by fences,
sidewalks or other objects, you may wish to
set Robomow to work in more than one zone.
Create separate zones in more than one way:
You may use one Perimeter Switch or one❍
Base Station
: Connect all zones
together in one long loop of the Perimeter Wire.
The Perimeter wire can be as long as 500
meters (1650ft) in one loop
Or
:
You may set❍both Base Station
and a
Perimeter Switch: Connect one or more zones
to the Base Station. In addition, connect other
zones to a Perimeter Switch available as an
accessory for RL2000.
The Perimeter Switch may be moved from one
zone to another.
To switch zones, Robomow will be driven or
carried to the proper location.
Indoor power supply
fixed to the wall
Max
15 m (50 ft)
The Fence
should be
inside lawn
15 m (50 ft) extension
cord (low voltage)
Indoor use only
Base
Zone
Zone A
Zone B
Maximum length of
wire connected to the
Base Station in one
loop is 500 m (1650 ft)
While the picture shows two wires
separate, they should be adjacent
Base
Station
Base
Station
Min 1 m
(3 ft)
<1 m
(3 ft)
Perimeter Switch
Chapter 1-3
Planning
Will Robomow be driving through a narrow pass in order to1.2.3
move between two connected zones?
A narrow pass is part of the lawn that connects two larger zones.
The width of this pass determines how it should be set-up.
If the pass… Setup:
Is walled (fence, building, etc)
and width is More than 2.00m (6.6 ft)
OR
Edge of pass is an open area
and width is more than 1.70m (5.6 ft)
Regular setup, as Robomow can
navigate between the areas while
mowing.
(Refer to paragraph 2.1.2).
Is walled (fence, building, etc)
and width is 1.5m – 2.00m (4.9 – 6.6 ft)
OR
Edge of pass is an open area
and width is 1.1m – 1.70m (3.6 – 5.6 ft)
Set as a “Narrow Pass”: Robomow
will drive through the pass, but will
NOT get across while mowing each
area.
(Refer to paragraph 2.2.2).
Is walled (fence, building, etc)
and width is smaller than 1.5m (4.9 ft)
OR
Edge of pass is open area
and width is smaller than 1.1m (3.6 ft)
Pass is too narrow.
Set the areas as 2 separate zones.
We want Robomow to enter the narrow pass in order to move
between these zones.
But, we do not want it to cross the pass while mowing each one
of them.
See Chapter 2, Base Station and Perimeter Wire
Setup
Note: Narrow passes require special setting of
Entry Points in order to start mowing in the adjacent
areas (see Chapter 7, Setting Robomow and using Advanced
Features)
Are there obstacles in Robomow’s mowing path?1.2.4
(Setting “Perimeter Islands”)
Obstacles such as flowerbeds, ponds, or small trees can be protected❍
from Robomow by setting “perimeter islands”.
Perimeter Islands are demarcated areas of the lawn, where
Robomow does not enter.
Obstacles that are vertical, relatively rigid and higher than 15cm❍
(6 inches), such as trees, phone or power poles, do NOT need
boundaries. Robomow will turn when it collides with these
obstacles.
However, for the gentlest and most silent operation, you may prefer to
create Perimeter Islands around all fixed objects in the working area.
If areas with obstacles are grouped closely together, they should be❍
demarcated by a single, continuous, Perimeter Island.
Pass wide enough. Robomow can effectively navigate
between the two areas while mowing the lawn.
Narrow Pass: Robomow will drive
through the pass, but will NOT get
across while mowing each area.
Base Station
Base Zone
Base
Zone
<1 m
(3 ft)
Chapter 2-1
Base Station and Perimeter Wire Setup
Base Station and Perimeter Wire SetupChapter 2
Recommendation, before you start:
During setup, you will insert pegs into the ground. To make this task
smoother, we recommend you mow your lawn and water it before starting.
Getting Ready
Confirm all parts needed for setup are within reach (refer to ‘What’s in the
Box, Introduction).
In addition, you will use the following tools:
Perimeter Wire Setup2.1
Before you start the setup, you should have a plan for the Perimeter Wire
layout and for the location of the Base Station
.
Laying the Perimeter Wire for the Internal setting of the Base Station is
different from the External setting.
Starting Point: Perimeter Wire at the Base Station area.2.1.1
❍Place the Base Station, according to your plan, with its fence
facing the inner lawn area.
Pull the plot connector and the wire connected to it out of the plastic
covering.
Do NOT remove the wire spool from its covering.
The plastic covering is the dispenser
for the wire.
If setting of Base Station is Internal (inside lawn)❍
Peg the beginning of the wire to the ground, where)
Base Station will be located.
Pull out 30 cm (12 inches) of wire and leave it loose at)
the Base Station location.
Later, at the end of the setup this part of the wire will
close the Perimeter Wire loop.
Start laying the wire in a counter-clockwise direction.)
Continue to pull the Perimeter Wire out of its covering,)
laying it loosely as you walk along the lawn edge.
Hammer Combination Pliers
Small flat and Philips
screwdrivers
Counter-clockwise
direction of wire layout
Perimeter Wire – do not remove
the plastic covering
Leave 30 cm
(12 inches)
starting point
Chapter 2-2
Robomow RL555, RL855, RL2000
If setting of Base Station is external (outside lawn)❍
Peg the beginning of the wire to the ground, at a distance of)
1m (3.3 feet).
Pull out 40 cm (16 inches) of wire and leave it loose at the)
Base Station location. This allows for later adjustments of
the Base Station.
Start laying the wire in a counter-clockwise direction at the)
external area of the Base Station.
Continue laying the wire for at least 30 cm (12 inch) away from●
the lawn.
Set a Narrow Pass, 20 cm (8 inches) wide, in the direction of●
the lawn, until the wire is 30 cm (12 inches) inside the lawn.
Continue to pull the Perimeter Wire out of its covering,)
laying it loosely as you walk along the lawn edge.
20 cm
(8’’)
30 cm
(12’’)
1
Starting point – 1 m (3.3 ft)
from lawn’s edge
2
Leave 40 cm (16’’) of
coil at starting point,
for later adjustments.
3
Continue for at
least 30 cm (12’’)
away from lawn.
4
Set a narrow pass of
20 cm (8’’) towards
lawn. Continue until
wire is 30 cm (12’’)
inside lawn.
5
Continue laying the
wire, using RoboRuler
along edges.
Chapter 2-3
Base Station and Perimeter Wire Setup
Laying the Perimeter Wire2.1.2
The Perimeter Wire is secured to the ground by the pegs supplied with❍
Robomow. Insert pegs every few meters and at corners.
At this early stage set a minimum number of pegs. Later, after testing
the wire setup, you will insert all necessary pegs.
Continue laying the wire, according to your plan.❍
Gradually pull it out of its dispenser and lay it loosely as you are moving
in a counterclockwise direction.
After uncoiling sections of wire, before inserting pegs, use the❍
RoboRuler to determine the distance of the wire from lawn edge or
obstacles.
If Outer Area Adjacent To Lawn… Distance Of Border From Wire
Is clear of obstacles.
Is lower than lawn
(OR of about the same height).
(e.g. same level sidewalk, flowerbed)
Short distance
(30 cm / 12 inch)
Is an obstacle
Or, is higher than the wire
(e.g. wall, fence).
Long distance
(45 cm / 18 inch)
Special cases of Perimeter Wire setup2.2
Perimeter islands2.2.1
Continue uncoiling the wire, moving from the edge towards the obstacle.
Apply RoboRuler’s “short distance” to peg the Perimeter around the
obstacle as shown in the drawing (clockwise direction).
Long distance
Short distance
Area outside perimeter - same basic
level and free of obstacles.
Area outside perimeter - has a
wall as an obstacle.
Direction of setup: clockwise
around obstacle
Min. distance between islands: 1 m (3 ft).
Otherwise, demarcate jointly as one island.
Perimeter Wire position
2 wires under
same peg
Perimeter
wire
Perimeter Switch
Chapter 2-4
Robomow RL555, RL855, RL2000
Caution! Setting the Perimeter Wire counter-clockwise around
the obstacle will cause Robomow to drive into the island.
Complete bordering the island and return to the spot that❍
where you have left the lawn’s edge.
The wires leading to the Island and returning from it should be❍
parallel and touching.
BUT DO NOT cross them!
Peg both wires, to and from the island, together with the❍
same peg.
Robomow will not recognize these two wires.
It will mow over them as if they do not exist.
Robomow will recognize the single blocking wire around the Perimeter Island
and will not enter this area.
If protected obstacles are grouped closely together, demarcate them by a
single, continuous, Perimeter Island.
If obstacles are close to the edge, leave them out of the mowing area.
Narrow passes2.2.2
A narrow pass is part of the lawn which connects two larger zones.
Following the Perimeter Wire, Robomow drives between these zones. But,
it does not cross the pass while mowing each one of them.
Set the two wires parallel along the pass at a fixed distance of❍
20 cm (8 inches) between them (Marked on RoboRuler).
If the distance between the wires is smaller than that, the two areas should
be set as 2 separate zones.
Base Zone
Base Zone Base Zone
If wire lays near
a wall or a fence,
keep a distance
of 65 cm (25’’)
between wire and
wall.
Distance of
20 cm (8’’)
between wires.
Especially
important near
pass’ entrances
Other manuals for RL2000
1
This manual suits for next models
2
Table of contents
Other Robomow Lawn Mower manuals
Robomow
Robomow RK2000 Installation manual
Robomow
Robomow RC304 User manual
Robomow
Robomow RK1000 User manual
Robomow
Robomow RC312 Pro S User manual
Robomow
Robomow RT300 User manual
Robomow
Robomow RC304u Use and care manual
Robomow
Robomow RC302 User manual
Robomow
Robomow RX20 Pro Installation manual
Robomow
Robomow RC304 User manual
Robomow
Robomow RC User manual
Robomow
Robomow Tuscania 200 User manual
Robomow
Robomow RS 630 2015 User manual
Robomow
Robomow RM400 Instruction Manual
Robomow
Robomow RC302 User manual
Robomow
Robomow RS User manual
Robomow
Robomow RS User manual
Robomow
Robomow RX Owner's manual
Robomow
Robomow RX20 Pro User manual
Robomow
Robomow RT300 User manual
Robomow
Robomow RK1000 User manual
