Rockford Fosgate PEQ User manual

Universal
PEQ
Quick
Setup
Features
•
Built-in
line
Driver
•
Accepts
High/Low
Level
Inputs
•
Auto
Turn-on
•
Universal
Punch
EQ
Specifications
Operating
Voltage
Idle
Current
Freqency
Response
Output
Voltage
THD+N
Turn-on
Delay
Output
Impedance
Input
Sensitivity
S/N
Ratio-
CEA
2006
S/N
Ratio-
1
OV
Channel
Seperation
Common
Mode
Rejection
Ratio
Fuse
Rating
Punch
EQ
9-16V
200mA
20Hz-20kHz
10V
0.005%
<1.0
sec
500
Ohms
600mV-10V
>100dB
>110dB
>80dB
>50dB
1A
0-18dB
@
45Hz
LP
0-14dB@
12.5kHz
HP
Output
Level
Adjustment
(The
output
level
control
is
used
to
match
the
output
of
the
audio
source
.)
===~-------------
-.
NEG
Batte
Switched
12V
to
REM
~ess
than
18"
+
POS
(When
utilizing
high-
l
o,vel
for
input
signal
the
auto
turn-on
feature
is
active.)
-------------
.&_CAUTION
Gain
I
Level
Adjustment
(The
amplifier's
Gain
I
Level
should
be
set
to
the
lowest
position
.)
1
I
I
I
I
I
I
REM
Out
(The
REM
is
an
output
to
turn
on/off c
dditional
accessories.)
Connect
to
chassis
ground
of
vehicle
*Keep
grounds
as
short
as
possible.
For
Motorsport
and
Boat
applications,
the
ground
wire
should
go
directly
to
the
negative
battery
terminal.
Maximum
~
:::
Boost
1
I
0
::::
I +10
:
+8
IJ '- -
J
+6
I
dB
+4
I
fl
~
v_:
.....
I
_...
I
~
I
~
I
I
I
I
I
~
~
~
1'1
......
--:"
-
I
5k
10k, 20k
Treble

PEQ Remote Installation
The remote can be mounted in a variety of ways. Use the following instructions to mount the remote that suits your application.
1. Find a location that gives easy access to the remote.
2. Route the cable for the remote and connect to the amplifier, Figure 1.
Outside Panel Install
3. Using the screws supplied, install the mounting clip.
NOTE: The housing can be installed with the mounting tab up or down.
See Step 1 in Figure 2, use a small flat-blade screwdriver in the slot at the top of the remote and
pry the remote assembly from the housing. Reinstall housing as desired.
4. Slip the remote onto the mounting clip until it snaps into place.
5. Connect the cable to the back of the remote.
Panel Install-Disassembly
NOTE: The maximum panel thickness is 3/16" (0.1875" or 4.75mm) for this type of installation.
Disassemble the remote as shown in Figure 2 as follows;
1. Use a small flat-blade screwdriver in the slot at the top of the remote and pry the remote assembly from the
housing.
2. Pull the control knob straight off to remove.
3. Use a paper clip or the flat side of a small drill bit from the back side through the hole to push the cover plate
off the housing cover.
NOTE: If the clear plastic LED extender is attached to the cover plate, remove it.
4. Remove the nut and washer and remove the remote assembly from the housing cover.
Panel Install-Standard
Ensure there is enough room within the panel area for connection and placement.
1. Use the plate with the LED hole as a template for hole positions.
2. Drill a 9/32 " hole (0.281" or 7.14mm) for the knob shaft and a 3/32 " hole (0.094" or 2.39mm)
for the LED through hole .
3. Install the remote from the back side of the panel, aligning the knob shaft and LED with the
drilled holes.
4. Install the cover plate washer and nut. Do not over-tighten the nut, just tighten until firm and secure.
5. Turn the knob shaft counter-clockwise to it's lowest setting. Position and install the knob.
6. Connect the cable to the back of the remote.
Panel Install-Separated LED Placement
CAUTION: We suggest the following be done only by an experienced installer. Use of a
grommet and/or double-sided tape (both not included) may be needed for a proper fit of the
LED. Rockford Fosgate will in no way be held responsible for damage incurred by improper
or novice installation.
0
Ensure there is enough room within the panel area for connection and placement.
1. Remove the LED from the rem0te assembly by pulling straight up, Figure 3 f
2. Connect the supplied cord to the LED. ~
3. Connect the cord from the LED into the 2-pin connector behind the knob shaft housing. ~
4. Drill a 9/32" hole (0.281" or 7.14mm) for the knob shaft. ~
5. Install the remote from the back side of the panel, aligning the knob shaft with the drilled hole.
6. Install the cover plate without LED hole, washer and nut. Do not over-tighten the nut, just tighten until
firm and secure.
7. Turn the knob shaft counter-clockwise to it's lowest setting. Position and install the knob.
8. Locate the position of the LED hole where the cord is not being over-extended.
9. Depending on the method of mounting, either a grommet and/or double:_sided tape, drill the hole for a
snug fit. Install the LED.
1 0. Connect the cable to the back of the remote. CAUTION: Over excursion and subsequent damage
Figure 1
0
Figure 2
Figure 3
_ __ 4 ~.-,__.~~ ...... _ _____ m_a_y _oc_cu_r_at_h-ig-h _lev_e_ls-of_b_oo_st_. --------------'
- ~r fAIIUa'a,~N' .. 1230-58703-01