RockJam RJFSDK01 Owner's manual
Full Sized Drum Kit- RJFSDK01 Assembly Information
Box Contents:
ABass Drum x1
GBass Drum Head x2
cSnare Drum Bracket x1
gTension Bolt Large x12 hTension Bolt Small
With Washer x12
dBass Drum Spur x2 e f
Drum Beater x1 Tension Bolt Claw x12
M
VW
Drum Pedal x1
NCrash Cymbal x1
Floor Tom Leg x3 XCrash Cymbal Rod x1 aTom Arm x2
Drum Sticks x2
b
YHi-Hat Inner
Rod x1 ZHi-Hat Outer
Rod x1
OHi-Hat
Cymbal x2
QStool Stand x1 RSnare Drum Stand x1 SCymbal Stand x1 TStool Seat x1 UStool Seat x1
PHi-Hat
Stand x1
HFloor Tom Tension
Rim x2 IFloor Tom Head x2 J
LK
FBass Rim x2
Floor Tom Drum x1
B C Snare Drum x1
E
Mid Tom Drum x1 High Tom Drum x1
D
EN 1
© PDT LTD 2022
RockJam RJFSDK01 User Guide EUROPE 170322_EN
Seat Bolt
Washer x1
Wing Nut Large x1
Seat Bolt x1
Tension Bolt
Key x1
If you find that you have any parts missing
We will then send out the missing parts as
our priority.
MISSING PARTS
PRE-ASSEMBLED
L
M
Tension Bolt
Key x1
K
N
N
Wing nut
Washer
Felt Washer
Crash Cymbal x1
Q
Q
Stool Stand x1
R
R
Snare Drum Stand x1
EN 2
Snare Drum Stand Assembly
Stool Assembly
Crash Cymbal Assembly
Drum Pedal Assembly
Unscrew the bolt on the snare drum bracket. Place the drum rod
into the stand and tighten. Position the brackets as shown in the
diagram. Screw the bolt back into place.
Place the seat onto the stool and into
the stand. Adjust to the required height.
Screw the seat bolt tightly into place.
Unscrew the wing nut from
the rod and remove the top
washer and felt washer.
Place the cymbal on the rod
on top of the felt washer
and bottom washer.
Place the top washers in the
order shown on the diagram
and tighten the cymbal into
place using the small wing
nut. Place the crash cymbal
rod into the cymbal stand.
Place the drum beater into
the top of the drum pedal.
Tighten the beater into
place using the tension
bolt key.
Washer
Felt Washer
cSnare Drum Bracket x1
TStool Seat x1 UStool Seat x1
T
U
VDrum Pedal x1 eDrum Beater x1
e
V
c
XCrash Cymbal Rod x1
SCymbal Stand x1
M
LK Seat Bolt
Washer x1
Wing Nut Large x1
Seat Bolt x1
J
J
S
X
Pinch the metal
poles under the
pedal and slot
into the holes to
secure.
EN 3
B
G
G
F
F
Bass Drum Assembly
Floor Tom Drum Assembly
x 6
x 6
A
Tighten the tension bolts
evenly with the key until
a good sound is achieved.
Tighten the tension bolts
evenly with the key until
a good sound is achieved.
Place the Floor Tom Legs into the drum and secure
into place by tightening the bolts by hand.
The large head with RockJam
logo (G) needs to go on the top
of the drum as shown in the
diagram.
H
H
I
I
I
Floor Tom Head x2
FBass Rim x2
fTension Bolt Claw x12
gTension Bolt Large x12
f
f
g
g
HFloor Tom Tension
Rim x2
WFloor Tom Leg x3
hTension Bolt Small
With Washer x12
h
h
W
ABass Drum x1
GBass Drum Head x2
Floor Tom Drum x1
B
Tension Bolt
Key x1
J
Tension Bolt
Key x1
J
J
J
J
J
x 6
x 6
EN 4
Hi-Hat Cymbal
Assembly
P
O
Z
OHi-Hat
Cymbal x2 PHi-Hat Cymbal
Stand x1
Tighten
1 cm 2 cm
Adjust
Tighten
Adjust
P
O
Z
Slide the metal bolt,
two felt washers and
plastic nut off the
inner rod (Y).
Adjust the stand legs so the pedal is flat on the floor, then tighten the stand bolt by hand.
Slide the bottom Cymbal (O)
over the Inner rod (Y) and place
onto the Outer Rod (Z).
Place the top cymbal piece onto the inner
rod. Adjust the outer rod height so there is
a 2cm gap between the cymbals and
secure in place.
Adjust the bottom cymbal screw so that
there is a slight slope as shown.
Assemble the top
cymbal (O) as shown.
Top metal bolt –
Felt washer –
Cymbal (O) –
Felt washer –
Plastic Nut.
Slide the Inner Rod (Y) into
the Stand (P) and then place
the Outer Rod (Z) on top.
Pinch the metal
poles under the
pedal and slot
into the holes to
secure.
YHi-Hat Inner
Rod x1 ZHi-Hat Outer
Rod x1
Y
High Tom Drum Mid Tom Drum
Final Assembly
Drum Pedal Attachment
Mid Tom Drum and High Tom Drum
x 2
Place the bass drum
spurs into the bottom
of the bass drum and
tighten into place. The
bottom of the spurs can
be adjusted for hard or
soft coverings.
Place the 2 x tom arms into the top of the bass drum making sure that the top is tilting towards
the drummer. Tighten into place.
Slide the high tom drum and
mid tom drum into place on
the top of the tom arms.
The tom drums should
sit tilting towards the
drummer.
Clip the assembled drum pedal onto
the bass drum tension rim and fix in
place by tightening the wing nut by
hand.
Snare Drum Sound Adjustment
To adjust the sound of the
snare drum pull the plastic
tab at the side of the
drum until the preferred
sound is achieved.
aTom Arm x2
dBass Drum Spur x2
a
d
x 2
C
D
Y
Seperately place the top
cymbal inbetween the bolts
and washers and secure.
O
Soft Floor Hard Floor
Table of contents
Other RockJam Drum manuals
