Rockler Blum BLUMotion 34807 User manual

1
Blum 110° BLUMotion Inset
Frameless Hinge Instructions
Effective May 2018
Vertical Positioning of Hinges
Although Euro-style concealed hinges allow for vertical
adjustment, the mounting plate must line up with the hinge arm if
the two are to snap together and provide the maximum possible
adjustment range. The easiest way to accomplish this is to mark
aligning horizontal centerlines on both the door and the cabinet.
You need to consider the amount of the door’s overlay or inset
when calculating the centerline positions for the door.
1. For the top hinge, measure down from the top of the cabinet
opening to the desired mounting location (typically 2"-3") and
use a combination square to mark the horizontal centerline on
the inside of the cabinet. (For the bottom hinge, measure up
from the bottom of the cabinet opening.)
Note: Be sure your hinge positions will provide adequate
clearance for any pullouts.
2. To determine the centerline location on the door, start
with the distance you measured in Step 1 and subtract
the amount of the reveal at that edge.
3. Use the values calculated for the top and bottom hinge
locations in Step 2 and mark the horizontal centerlines on
the back of the door. Compare the distance between the lines
on the cabinet with the distance between the lines on the
door to verify.
Installing Hinges
1. Refer to the Door Diagram to mark drilling locations for the
hinge cup holes and mounting screw holes on the door.
2. Using a 35mm Forstner bit, drill a hole 13mm deep for
the hinge cup, taking care to keep the bit as square as
possible to the door.
Note: For fast, easy and accurate location and drilling of hinge
cup holes, we recommend using the JIG IT Deluxe Concealed
Hinge Drilling System (53420, sold separately) along
with a Rockler 35mm Long-Shank Forstner Bit (10117, sold
separately). For those using a drill press, a dedicated JIG IT
setup block is available (58488, sold separately).
3. Drill pilot holes for the screws, taking care not to drill all
the way through the door.
4. Position the hinge cup in the hole and use the included
screws to secure in place.
5. Repeat Steps 2-4 at other hinge location(s).
Installing Mounting Plates
1. Refer to the Cabinet Diagram to mark drilling locations for
the hinge plates.
2. Drill pilot holes for the mounting screws, taking care not
to drill all the way through.
Note: For fast, easy and accurate location and drilling
of mounting plate pilot holes, we recommend using the
JIG IT Hinge Plate Template for Inset Doors (56585,
sold separately) along with a Rockler/Insty-Drive
#6 Self-Centering Bit (68991, sold separately).
3. Use the included screws to secure the mounting plates
onto the cabinet.
4. Mount the doors by clipping the hinge arms onto the
mounting plates.
Hinge Finish Tab Cup
Diameter
Cup
Depth
Minimum Door
Thickness
Maximum Door
Thickness Adjustments Gap Clip-on
Mounting
Minimum
Reveal
Blum 110°
Long Arm Nickel 5mm 35mm 13mm 16mm (.63") 26mm (1") 3-way cam NA Yes .5mm
Check Rockler.com for updates. If you have further questions, please
contact our Technical Support Department at 1-800-260-9663
or [e-mail]
BLUMotion
Soft Close
On/Off
Switch
34807
Full
Overlay
110º
Opening
Soft
Close

2Distributed by Rockler Companies, Inc.
Medina, MN 55340
34807
Rev 05/18
3232
5
22.5
Cabinet
All measurements
are in millimeters.
Cabinet Diagram
Turning this screw clockwise adjusts the
door down; counterclockwise, up.
Turning this screw clockwise adjusts the
door inward; counterclockwise, outward.
Height Adjustment Depth Adjustment Lateral Adjustment
Turning this screw clockwise adjusts
the door to the right; counterclockwise,
to the left.
9.5
45
Inside Edge
of Door
Tab
Center
Mark Centerline
OPTIONAL ACCESSORIES
JIG IT®Deluxe Concealed
Hinge Drilling Jig
53420
JIG IT®5mm Hinge Cup
Drill Press Drilling Jig
58488
JIG IT®3/4" Thick Inset
Door Hinge Jig
56585
Cup Spacers and Angle
Restriction Clips
35245 and 47937
Cup Depth Diagram
13
35
Door
Cabinet
Reveal Diagram
Reveal
Door Diagram
Door thickness plus 37
(56 for 3/4" thick door)