Rockwell Automation 1336 PLUS User manual

Instructions
What this Option Provides The Enclosure Kit provides the required materials to enclose an open
chassis 1336 PLUS or 1336 PLUS II in an enclosure. When properly
installed, each Enclosure Kit is designed to meet IP 65 (NEMA Type
4) standards or IP 54 (NEMA Type 12) standards and permit the drive
heatsink to extend outside the enclosure. You must observe the
general installation requirements that are provided in the installation
section of your drive User Manual.
Where this Kit is Used The Enclosure Kit is used in the following ranges:
What the Kit Contains Each IP 65 (NEMA Type 4) Enclosure Kit contains the following:
•(1) Pre-assembled IP 65 (NEMA Type 4) enclosure with fan1.
•(1) IP 65 (NEMA Type 4) permanent adhesive backed gasket.
•M5 x 0.08 x 10M sems or hex head screws.
Each IP 54 (NEMA Type 12) Enclosure Kit contains the following:
•(1) Pre-assembled IP 54 (NEMA Type 12) enclosure with fan1.
•(1) IP 54 (NEMA Type 12) permanent adhesive backed gasket.
•10-32 x 3/8 inch sems or hex head self-tap screws.
1
Fans are not required on A1, A2, and A3 frame enclosures.
Frame
Reference Enclosure Kit Catalog Number Used with 1336 S/F . . .
A1, A2, A3
1
1336S-AFA3, 1336S-AJA3 AQF05 - AQF50, BRF05 - BRF50
A4 1336S-AFA4B, 1336S-AJA4B BRF75 - BRF100
B1 1336-AFB1A, 1336-AJB1A A007
1336-AFB1B, 1336-AJB1B B007 - B015
1336-AFB1C, 1336-AJB1C C007 - C010
B2 1336-AFB2A, 1336-AJB2A A010 - A015
1336-AFB2B, 1336-AJB2B B020 - B030
1336-AFB2C, 1336-AJB2C C015 - C020
C1336-AFCA, 1336-AJCA A020 - A030
1336-AFCB, 1336-AJCB B040 - BX060
1336-AFCC, 1336-AJCC C025 - C060
1336 PLUS and PLUS II IP 65/54
(NEMAType 4/12) Enclosure Kit

21336 PLUS and PLUS II IP 65/54 (NEMAType 4/12) Enclosure Kit
To install the drive, follow these steps:
1. Place the gasket, with the gasket paper still intact, around the
cutout area on the inside of the enclosure. Assure that the
mounting holes are aligned properly (mounting holes are not
equally spaced).
2. Peel away the gasket paper.
3. Firmly press the gasket in place aligning with the enclosure holes.
4. Remove the screws holding the drive mounting rails to the drive
back panel.
5. Install the drive in the enclosure using the mounting screws
provided with the kit.
6. Torque all mounting screws to 2.9 N-m (26 lb.-in.).
7. Connect the fan wires (A4 Frames & Up) as shown in the next
section.
Wiring The following diagram shows the typical wiring diagram for all
frames. Note that a fan is not required on A1-A3 frames.
!ATTENTION: Electric shock can cause injury or death.
Disconnect all power before working on this product.
!ATTENTION:Driveheatsink surfacetemperaturemaybe
at or near 100 degrees C (212 degrees F). To avoid burns,
do not make contact with the drive heatsink.
Typical Inside View Typical Wire Connections
(460V Connections Shown)
Fan
Typical Transformer/Fan Location
Pre-assembled Wires (Furnished)
Typical Drive Location
0V 380V415V
115V 0V 460V
Fan
T1
19
TB3
TB2
TB1
20 21 22 23 24 25 26 27 28 29 30
TETE 1
1
2
2
34567
P
EP ED
C
+
D
C
–J
2
RSTUVW
TB1 P
EP ED C
+
D
C
–RSTUVW
8 9 10 11 12 1314 15 16 17 18 A1A2

1336 PLUS and PLUS II IP 65/54 (NEMAType 4/12) Enclosure Kit 3
IP 65/54 (NEMA Type 4/12) Dimensions
Typical Top and Bottom Detail A
See Detail A
See
Detail B
A
DFG
H
C
EB
12.7 (0.50)
12.4 (0.49)
7.9 (0.31)
Frame
Reference
A1
A2
A3
A4
B1
B2
C
A
430.0
(16.93)
430.0
(16.93)
430.0
(16.93)
655.0
(25.79)
655.0
(25.79)
655.0
(25.79)
655.0
(25.79)
B
525.0
(20.67)
525.0
(20.67)
525.0
(20.67)
650.0
(25.59)
650.0
(25.59)
900.0
(35.43)
1200.0
(47.24)
C
350.0
(13.78)
350.0
(13.78)
350.0
(13.78)
425.0
(16.74)
425.0
(16.74)
425.0
(16.74)
425.0
(16.74)
E
500.1
(19.69)
500.1
(19.69)
500.1
(19.69)
625.1
(24.61)
625.1
(24.61)
875.0
(34.45)
1174.5
(46.22)
D
404.9
(15.94)
404.9
(15.94)
404.9
(15.94)
629.9
(24.80)
629.9
(24.80)
629.9
(24.80)
629.9
(24.80)
F
250.0
(9.84)
250.0
(9.84)
250.0
(9.84)
293.0
(11.54)
293.0
(11.54)
293.0
(11.54)
293.0
(11.54)
G
N/A
N/A
N/A
63.5
(2.50)
63.5
(2.50)
63.5
(2.50)
63.5
(2.50)
H
N/A
N/A
N/A
76.2
(3.00)
76.2
(3.00)
76.2
(3.00)
76.2
(3.00)
All Dimensions in Millimeters and (Inches)
7.1 (0.28) Dia.
12.7 (0.50)
12.7 (0.50) Dia.
14.3 (0.56) Dia.
Drive
Heatsink
Detail B
19.1 (0.75) 19.1 (0.75) Dia.
5.5 kW (7.5 HP) at 200-240V AC
11 kW (15 HP) at 380-480V AC
7.5-11 kW (10-15 HP) at 200-240V AC
15-22 kW (20-30 HP) at 380-480V AC
Approx. Ship
Weight
16.8 kg
(37.0 lbs.)
17.9 kg
(39.4 lbs.)
18.6 kg
(41.0 lbs.)
39.5 kg
(87.0 lbs.)
44.7 kg
(98.5 lbs.)
56.5 kg
(124.5 lbs.)
80.7 kg
(178.0 lbs.)

Publication 1336 PLUS-5.66 – May, 1999 P/N74002-139-01(01)
Supersedes February, 1996 Copyright 1999 Rockwell International Corporation. All rights reserved. Printed in USA.