Rocky Mountain RMR-C410 User manual

RMR-C410
Radar and Laser Detector
Owners Manual
SPECIFICATIONS:

Radar & Laser Detector:
Frequencies: 10.525 GHz
24.125 GHz
33-36 GHz
904 Nano-meter
Sensitivity: X-112 Dbm
K-110 Dbm
Ka-wide-102 Dbm
Laser < .5 microwatt
Alarm: Separate for each Band
Variable alarm for Range
Controls: Volume, On/Off, Dim, Mute,
City/Highway, Test
VG-2: Automatic Frequency Shift
Size: 1.4” x 3.0” x 4.4”
The RMR-C410 detector is a full-featured radar and
laser detector.
The radar detector is a dual conversion scanning
superheterodyne receiver with separate alarms for
each of the radar bands, dim function, city/highway
and mute select. It detects front and rear laser and
radar.
Other:
One-Year Ticket Rebate Program
Three-Year Warranty
FCCID: QKK-C02
This product has been designed and certified to
comply with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved
by Rocky Mountain Radar may void your
authority to use this product. Operation is subject
to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
2
Installation:
1) Attach the windshield bracket to the C410
detector. Align the edge on the bracket with the slot

opening on the front of the case. Slide the bracket
into the case until it locks into place.
2) Place the windshield bracket in the upper center
portion of the windshield. The ideal position will be
right below the rear view mirror. Press firmly to seat
the suction cups. Note: Tinted glass may degrade the
laser performance.
3) Bend the windshield bracket mount to a level
position.
4) The RMR-C410 will hang from the bottom of the
bracket and must have an unobstructed view of the
road ahead.
5) Insert the small end of the power cord gently into
the power jack on the right side of the unit and the
large end into the cigarette lighter receptacle.
Remote mounting is not recommended.
Hard wire: Remove cigarette lighter plug. Connect
the black with white stripe wire to +12 Volts, and
then connect the solid black wire to ground.
3
CONTROLS: There are 4 buttons on top of the
C410, Test, Dim, Mute and City.

Dim: Press the Dim button for one second to dim the
alarm lights. There are 3 levels of brightness. To
brighten the alarm lights press the dim button again.
Mute: Press the Mute button for one second to
disable the alarm speaker for quiet operation. To
reactivate the alarm speaker press the Mute button
again for one second.
City: Press the City button for one second to reduce
false alarms in high RF noise areas. The yellow City
light will illuminate to show activation.
Test: Press and hold the test button for any length of
time to perform a manual test. When pressed you will
hear a soft chirping sound and the yellow light will
come on.
Reminder! The C410 will memorize the settings of
the features above when the unit is powered off.
Be sure to readjust the settings to your normal
preferences.
Power and Volume: Power is provided through the
thumb wheel switch on the left side of the unit.
Rotate the wheel forward to turn on and increase the
volume for the alarm.
4
Alarms: A separate alert tone will sound for each
band of Radar encountered with a different colored
light, (Ka-Green), (K-Yellow), (X-Red) illuminated.

Tone frequency will increase as signal strength
becomes stronger. (Fig. A)
All alarm lights will flash when Laser is detected.
(Fig. B)
VG-2: VG-2 detection is indicated with a separate
alarm along with the green power light blinking. VG-
2 will make you undetectable to radar. (Fig. C)
Diagnostics: The RMR-C410 has a full internal
automatic diagnostic system. If the power light goes
off and remains off, check the 2-amp fuse in the
power cord by unscrewing the silver tip and
removing the fuse. If the fuse is good (wire inside the
fuse unbroken), return the unit for service.
Rocky Mountain Radar does not condone the use
of excessive speed on the highways, nor does it
endorse breaking the speed limit laws of the
United States of America. Please drive safely when
using this or any other electronic product in your
car.
5
Selectable VG-2:
To activate VG-2 detection turn the unit on. After the
self-test has completed, press and hold the Mute

button down for 3~5 seconds until the unit beeps
three times. VG-2 detection is now activated. To
deactivate press and hold the Mute button for 3~5
seconds until the unit buzzes once. VG-2 is now off.
Auto Memory: The RMR-C410 has an automatic
memory. Any settings enabled when the unit is
turned off will still be enabled when the unit is turned
back on. If you have set the unit on Mute or have
dimmed the alarm lights be sure to readjust the
settings to your normal preference.
Fig. A
6
Warranty

The RMR-C410 is guaranteed against defects in
workmanship and materials for 36 months from the
date of purchase. Should any malfunction occur, the
unit would be repaired or replaced by the factory at
no charge. You may have your unit checked free of
charge at the factory during this warranty period.
Returns should be sent freight prepaid with an
explanation of the problem, your physical address (no
PO Boxes) and telephone number. Send to:
ROCKY MOUNTAIN RADAR
6469 Doniphan Drive
El Paso TX 79932
Phone: [phone] Fax: [phone]
We do not accept COD shipments
We do not accept freight collect shipments
Accessories
The following accessories and parts are available:
Windshield mount $ 5.00
Suction Cups (set of 3) $ 2.00
2 amp fuses (two each) $ 2.00
Power Cord $ 5.00
Replacement Owners Manual $ 3.50
Set of Colored Bezel Panels (6) $10.00
Set of Da-Glo Bezel Panels (3) $10.00
A $10.00 shipping and handling fee will be added to
the total of each order.
VISA/MC and Discover Accepted
Tamper Fee
Tampering with, disassembly, or modification of this
product voids the warranty and a tamper fee of
$150.00 will be charged to repair it.
7

Manufactured Exclusively by
Rocky Mountain Radar in the USA