ROGERSELLER Eccentric User manual

Installation
Instructions
Basin Set
Eccentric
by Rogerseller

Specification
Recommended Tools
Shifting Spanner
Pipe Cutter
Ruler
Notes Before Installation
• Replace, clean and lush supply
as necessary.
• Shut o mains water supply.
• Inspect supply lines for any signs
of damage or foreign material.
• Check all reference dimensions
to ensure tap set suitable for
application.
• Check the product and it’s
packaging are un-damaged.
• If product is found to be defective
or parts are missing please contact
point of sale.
Eccentric by Rogerseller
Basin Set
3606013101 — Chrome
Other inishes available

Installation
Step 1
Measure centre distance of basin / bench
and conirm maximum distance between tap
holes is 220mm.
Step 2
Trim the tee-piece using a pipe cutter to suit
the centre distance of the basin tap holes. As
a guide, place the tee-piece in the centre of
the spout hole and mark on it the inner edge
of the tap holes. Trim at this point and remove
sharp edges..
Step 3
Ensure the O-ring is located between the
spout lange and basin to seal out any water.
Place the spout assembly into appropriate
basin hole and secure it in place using the
supplied washer and back-nut.
220mm Max.
Between Centres
40mm Max.
Bench Thickness
Spout Assembly
O-ring
Washer
Back-nut

Installation
Step 5
From the underside, place the basin assembly
into appropriate holes so as the tee-piece
engages the spout. Screw the basin lange
with O-ring onto the basin body assembly as
far as it will go. Secure the basin assembly in
place by tightening the basin body lock-nuts.
Note: Spacer requirement is dependant on bench thickness.
Ensure O-ring located in each basin lange before securing
in place.
Step 6
With the ceramic valves in the o position,
orientate each handle assembly as shown in
the diagram.
Place handle on and engage the spline
adaptor. Using the allen key supplied tighten
the grub screw to ix the handle in place.
Gently push the Cap into hole until lush with
the outside.
Step 4
Screw one basin body lock-nut onto each
of the basin body assemblies all the way.
Then place the compression nuts and olives
onto the tee-piece, then it the basin body
assemblies to each end of the tee-piece.
(Only hand tight at this stage of installation).
Note: Place the assembly upside down into the appointed
holes to check/obtain correct centre distances.
Basin Flange
O-ring
Spacer
Spline Adaptor
Basin Body Assembly
Basin Body Lock-nut
Olive
Compression Nut
Tee-piece
Ensure O-ring is located
in groove of basin lange
For basin’s thicker than
10mm Spacer not required
Tighten Lock-nut
Correct Handle Orientation
Cap
Allen Key
Grub Screw
Handle

Installation
Step 7
Connect supply lines using your preferred
method in accordance with AS/NZS3500,
connect the mains water supply lines to the
appropriate hot and cold basin body.
(hot marked with red tape).
Introduce mains supply, check for leaks and
remedy if required.
COLD
HOT

rogerseller.com.au
Speciications
It is a requirement of state plumbing codes that licensed plumbers carry out all tapware installations.
All installations must comply with the relevant requirements of AS/NZS3500 and local plumbing
codes.
Pressure
Maximum Hydrostatic Pressure - 1000kpa
Recommended Maximum Hydrostatic Pressure - 500 kpa. (AS/NZS 3500)
Recommended Minimum Hydrostatic Pressure - 150 kpa.
Maximum Hydrostatic Pressure may be exceeded under test conditions only in accordance with AS/
NZS 3500. Where hydrostatic pressure exceeds the maximum stated above, pressure limiting valves
must be installed or warranty will be void.
Temperature
Maximum Water Temperature - 80°C
For optimum performance, Hot and Cold inlet water pressure should be equal.
Sink Requirements
Tap Hole Size - Ø32 - 35mm
Spout Hole Size - Ø26 - 32mm
Maximum Bench Thickness - 40mm
Care and Maintenance
[1] Product should be inspected for surface damage prior to installation. [2] Cleaning and handling
of all inishes must be performed carefully. [3] Clean products using a soft cloth with warm soapy
water only. [4] Never use harsh detergents or abrasive cleaners as these will damage the product.
[5] Water marks can be removed from Matt Finishes with an application of a carnauba wax based
non-abrasive polish on a microibre cloth. [6] Do not use undue pressure when cleaning and wipe
in one direction only. [7] Contact with harsh chemicals such as hair dye, hair bleach etc will result
in damage to the inish. [8] Tapware should never be installed using acetone silicones. [9] Avoid the
use of wax based furniture creams as this can result in a build up of deposits which will detract from
the appearance. [10] Damage to inishes arising from improper installation or post installation use or
failure to observe the above care and cleaning instructions will void all warranty agreements.
Warranty
Rogerseller tapware, bathroom ittings and sanitaryware are covered by a ive (5) year warranty from
date ofpurchase. Forfullterms and conditions please refer to rogerseller.com.au
Dimensions are approximate. Information in this installation instruction is representative of the product available at
the time of printing. Due to our policy of continuous product development, the design and speciications depicted
are subject to change without notice. Please conirm all particulars with your client advisor prior to purchase.