ROGERSELLER Tonic User manual

Installation
Instructions
Gooseneck Pull Out Sink Mixer
Tonic
by Rogerseller

Parts List
1. Mixer Tap Assembly
2. Pull-out Hand Piece
3. Outlet/Fixing Rod
4. Rubber Base Washer
5. Rubber Horseshoe Washer
6. Metal Horseshoe Washer
7. Spacer
8. Nut
9. Dual Check Valve Assembly
12. 1.5m Pull-out Hose
13. Counter Weight
14. Counter weight Hose Clip
Tonic by Rogerseller
Gooseneck Pull Out
Sink Mixer
3606013801 — Chrome
1
2
3
4
5
6
7
8
9
12 13 1410 11

Installation
Step 1
If not already done so, disassemble the
the mixer tap assembly, pull out hose and
Guide the 1.5m pull-out hose and mixer tap
assembly into the sink hole.
Bench Hole Requirements:
Minimum Hole Size - Ø32mm
Maximum Hole Size - Ø35mm
Step 2
From the underside, apply the rubber
horseshoe washer, metal horseshoe washer,
hole so the base washer achieves a seal and
into place by tightening nut.
1.5m Pull-out Hose
Mixer Tap Assembly
Sink Hole
32 – 35mm
Outlet/Fixing
Rod
Base
Washer
Nut
Fixing Rod
Rubber
Horseshoe
Washer
Metal
Horseshoe
Washer
Spacer Base
Washer

Installation
Step 3
Connect the dual check valve assembly to
hoses to the appropriate inlets. (shown in the
illustration) Screw all in a clockwise direction
by hand until they come to a stop.
Step 4
Connect inlet hoses to the mains supply then
connect the 1.5m Pull-out hose to the dual
check valve. Ensure inlet hoses don’t impede
movement of the 1.5m Pull-out hose.
Apply the hose counter weight to the lowest
point in the hose loop and apply clip to the
rearward side.
Take hand piece and unscrew from pull out
hose. Introduce mains water supply, open the
debris from installation. Re-install the hand
piece to complete the installation.
Hot Inlet
(marked with "H")
Mixed Outlet
Cold Inlet
Hose Clip
(rearward side)
Hose Weight
Mains (Hot)
Red Fiber Washer
Dual Check Valve
1.5m Pull-out Hose
(Opposite End)
Mains (Cold)
Rubber Washer

rogerseller.com.au
It is a requirement of state plumbing codes that licensed plumbers carry out all tapware installations.
All installations must comply with the relevant requirements of AS/NZS3500 and local plumbing
codes.
Pressure
Maximum Hydrostatic Pressure - 1000kpa
Recommended Maximum Hydrostatic Pressure - 500 kpa. (AS/NZS 3500)
Recommended Minimum Hydrostatic Pressure - 150 kpa.
Maximum Hydrostatic Pressure may be exceeded under test conditions only in accordance with AS/
NZS 3500. Where hydrostatic pressure exceeds the maximum stated above, pressure limiting valves
must be installed or warranty will be void.
Temperature
Maximum Water Temperature - 80°C
For optimum performance, Hot and Cold inlet water pressure should be equal.
Care and Maintenance
[1] Product should be inspected for surface damage prior to installation. [2] Cleaning and handling
water only. [4] Never use harsh detergents or abrasive cleaners as these will damage the product.
[5] Water marks can be removed from Matt Finishes with an application of a carnauba wax based
in one direction only. [7] Contact with harsh chemicals such as hair dye, hair bleach etc will result
use of wax based furniture creams as this can result in a build up of deposits which will detract from
failure to observe the above care and cleaning instructions will void all warranty agreements.
Warranty
Please note —
Dimensions are approximate. Information provided in these installation instructions is representative of the actual
products available at the time of printing. Due to our policy of continuous product development, the designs and
expert prior to purchase. Each product is covered by a limited warranty. Full terms and conditions are available
from your product expert.