ROGERSELLER Tonic User manual

Installation
Instructions
Shower on
Integrated Union
Tonic
by Rogerseller

Specification
Parts List
1. Hand Shower
2. Flow Controller
3. Conical Nut (with O-ring)
4. Shower Hose
5. Rubber Sealing Washer
6. Saddle
Tonic by Rogerseller
Shower on Integrated Union
3506003201 — Chrome
Other inishes available
1
6
2
5
4
3

Installation
Step 1
With approx. 1015mm of wall outlet
protruding the inished wall, place the wall
plate over the wall outlet.
Step 3
Take the Shower hose and connect the hose
end with the conical nut and o-ring onto the
hand shower ensuring the low controller is
positioned inside the conical nut.
Hook the hand shower into the saddle.
Connect the opposing end to the threaded
connection located on the underside of the
swivel bracket ensuring the rubber sealing
washer is in position.
Check for water tightness and remedy as
required.
Step 2
Apply a suicient amount of thread tape or
sealant to the wall outlet, then in a clockwise
direction, ix the swivel bracket to the wall
outlet until it reaches the wall plate and is in
the correct orientation as illustrated.
Min - 10mm
Max - 15mm
Wall Outlet
Wall Plate
Swivel Bracket
Rubber Sealing
Washer
Flow
Controller
Hand Shower
Shower Hose
Saddle
Conical Nut
(with O-ring)

rogerseller.com.au
Specifications
It is a requirement of state plumbing codes that licensed plumbers carry out all tapware installations.
All installations must comply with the relevant requirements of AS/NZS3500 and local plumbing
codes.
Where showers incorporate low controllers, instructions that care be exercised during installation
to ensure that the male connecting threads do not damage the low controllers.
A backlow prevention / dual check device must be installed to the bottom of the rail between the
rail end and the hose if the hand shower can reach the shower loor when installed.
Pressure
Maximum Hydrostatic Pressure - 1000kpa
Recommended Maximum Hydrostatic Pressure - 500 kpa. (AS/NZS 3500)
Recommended Minimum Hydrostatic Pressure - 150 kpa.
Maximum Hydrostatic Pressure may be exceeded under test conditions only in accordance with AS/
NZS 3500. Where hydrostatic pressure exceeds the maximum stated above, pressure limiting valves
must be installed or warranty will be void.
Temperature
Maximum Water Temperature - 80°C
For optimum performance, Hot and Cold inlet water pressure should be equal.
Care and Maintenance
[1] Product should be inspected for surface damage prior to installation. [2] Cleaning and handling
of all inishes must be performed carefully. [3] Clean products using a soft cloth with warm soapy
water only. [4] Never use harsh detergents or abrasive cleaners as these will damage the product.
[5] Water marks can be removed from Matt Finishes with an application of a carnauba wax based
non-abrasive polish on a microibre cloth. [6] Do not use undue pressure when cleaning and wipe
in one direction only. [7] Contact with harsh chemicals such as hair dye, hair bleach etc will result
in damage to the inish. [8] Tapware should never be installed using acetone silicones. [9] Avoid the
use of wax based furniture creams as this can result in a build up of deposits which will detract from
the appearance. [10] Damage to inishes arising from improper installation or post installation use or
failure to observe the above care and cleaning instructions will void all warranty agreements.
Warranty
Rogerseller tapware, bathroom ittings and sanitaryware are covered by a ive (5) year warranty from
date ofpurchase. Forfullterms and conditions please refer to rogerseller.com.au
Dimensions are approximate. Information in this installation instruction is representative of the product available at
the time of printing. Due to our policy of continuous product development, the design and speciications depicted
are subject to change without notice. Please conirm all particulars with your client advisor prior to purchase.