rojaflex HSR-1 User manual

FLEXIBLE SOLUTIONS
IN MODERN TECHNOLOGY
Rojaflex HSR-1 | HSR-5
Remote controller
For all Rojaflex drives and radio receivers
ORIGINAL
OPERATING MANUAL
V2.18-07.2020

www.rojaflex.com
Table of contents
EU Declaration of Conformity specified in Article 10.9
Company Schoenberger Germany Enterprises GmbH & Co. KG, Hohenschäftlarn delares hereby that the radio device
“Remote controller rojaflex HSR-1/HSR-5” conforms to Directive 2014/53/EU.
The complete EU Declaration of Conformity is available at:
https://www.rojaflex.com/konformitaetserklaerungen.html
Rojaflex HSR-1 | HSR-5
1 | 5 -channel remote
controller
For all Rojaflex drives and receivers
Safety guidelines................................... 3-4
Function review........................................5
Technical data/Packaging contents..........6
Programming and setup ....................... 7-9
2

3
www.rojaflex.com
Safety guidelines
WARNING
Important safety guidelines!
•Adherence to these guidelines is
important for safety of people!
•Please, keep this manual and when an
owner changes, pass it to the new
purchaser!
•The device can be used by children
over 8 years of age, and people with
limited physical, sensory or mental
capabilities, and without experience or
knowledge when they are supervised
or have been acquainted with a way
for a safe operation of the device, and
informed about hazards associated
with the device.
•Children should not play with the
device.
•Works associated with cleaning and
maintenance of the device cannot be
performed by unsupervised children.
WARNING!
Drives and receivers controlled by
transmitter should be disconnected from
power supply during cleaning,
maintenance, and replacement of parts.
WARNING!
Failing to comply with these instructions
may pose a hazard to life!
DURING all works on electrical devices
there is a risk of a hazard to life related to
the electrical shock!
Observe instructions and safety
guidelines concerning the controlled
drive/receiver, as well as relevant
instructions for driven sun protection
devices!
Safety guidelines!
CAUTION!
The following guidelines should be observed!
A range of radio controlling for radio devices is
regulated in the Act, and depends, among
others, on construction conditions.
During planning, take the sufficient radio range
into account. It is particularly important when
a transmitter is installed in a different room
than a receiver and the radio signal must
penetrate through walls or ceilings.
Do not install the radio control directly in a
vicinity of large metal surfaces.
Other transmitters (e.g., wireless headphones,
electronic nannies, radio weather stations) of a
transmitting frequency identical as a frequency
of the radio controller may interrupt the
reception.
CAUTION!
Observe guidelines for correct
operation and work conditions!
Incorrect operation increases a risk of
injury!
•The radio controller should only be
used to connect with roller blind,
awning or louvre drives.
•Permanently fixed (wall-mounted)
transmitters should be visible.
•In the case of snowfalls, icing, and frost
deactivate an automatic opening and
closing function of the transmitter, to
avoid damages to the motor or the
driven device.

4
www.rojaflex.com
Safety guidelines
•Only original parts and accessories from
the manufacturer should be used.
•Instruct all people on safe use of the
device.
•Observe the moving device (roller
blind/awning), do not allow people
near until the device stops.
•Children are forbidden to play with
radio receivers and transmitters.
•A remote controller should be stored
in such way that its unintended
operation, e.g., by playing children, is
not possible.
•Secure the controlled device against
access of unauthorised people.
Secure against unintended
switching on.
•Works associated with cleaning (of
roller blinds, awnings, louvres) should
only be conducted when power supply
is disconnected.
•Maintain caution when operating the
opened/closed device, as when any
fixtures are loosened or broken, some
parts (e.g., hangers, brackets) may
come loose.
WARNING!
The use of defective devices may
pose a hazard to people and cause
damage in property.
•After unpacking, compare the device
type to relevant information in the
nameplate.
A device that is incomplete or not
conforming to a specification cannot be
started.
•Never use a device that is defective or
damaged.
•Check whether the drive controlled
by the transmitter and the power
supply cord of the drive are not
damaged.
•When any damage is found, please
contact our Service. (See the last
page.)
IMPORTANT!
Do not throw the device or batteries
required for its operation away with
household waste!
Find information about possible local return
and recycling, and dispose of at special local
collection sites.

Function review
5
www.rojaflex.com
Depending on the switching frequency, we
recommend replacing the batteries at least
every 2 years.
LED
Channel display
K1 K2
UP
UP
Battery
compartment
STOP STOP
DOWN DOWN
DIP switch*
single/bi- SI
directional
P2
Programming BI
button
1 channel remote
controller HSR-1
5 channel remote
controller HSR-5 Individual
channels can be changed using
K1 and K2 buttons
When all 5 LEDs are lit, the group
control is active. All programmed
receivers are controlled
simultaneously.
The remote controller
back with a cover open
The “DIP switch” can be used to
choose between “SI” (single-
directional communication) and “BI”
(bi-directional communication),
depending on the receiver type (see
the receiver operating manual).
.
Battery installation/replacing
Depending on the transmitter model, the battery is delivered separately in the packaging, or is installed and
secured with a protective film against discharging. Open the back cover pressing it slightly down*, remove the
protective cover and install the battery (as shown) with the + (plus) side up. Then install the back cover.
Remove protective
film.
* Depending on a model, the
back cover can be held in place
with a screw.
The description of keys can differ, depending on a model:
K1= K- (minus) K2= K+ (plus)
Do not dispose of batteries together with
household garbage! Deliver to an appropriate
disposal site.

6
www.rojaflex.com
Technical data/Packaging contents
FLEXIBL E LÖSU NGEN
MI T DER TECHNIK VON H EUTE
Remote
Rojaflex HSR-1 | HSR-5
Für alle Rojaflex Funk-Rohrmotoren und Funkempfänger
1
2
3
ORIGINAL-
BETRIEBSANLEITUNG
V1. 03-12.20 19
Technical data
Parameters
Power supply 3V battery (CR2450)
Frequency 433.92 MHz
Operating current ≤ 15 mA
Quiescent current ≤ 15 μA
Consumption in a standby mode ≤ 5 μW
Transmitted power ≤ 10 mW
Protection IP 20
Acceptable ambient temperature +10°C to +50°C
Radio range Open space: ca. 150 m/closed rooms: ca. 30 m*
Number of channels 1-channel/ 5 -channel
Compatibility Rojaflex radio drivers and radio receivers
Dimensions 130 x 44 x 18 mm (HxWxD)
Packaging
contents
* Data on the range are approximations and depend on actual construction conditions.
After unpacking, please check the packaging contents against a list in this manual.
1. Remote controller with a battery
2. Wall bracket with a fixing system
3. Operating manual

Programming and setup
7
www.rojaflex.com
Each time, the button must be pressed within 4 seconds!
Otherwise, the system will automatically leave the programming mode.
SI
P2
BI
1. Programming (learning) mode - a radio-controlled drive or an external radio receiver
A radio receiver (a radio- controlled drive Rojaflex or an external radio receiver Rojaflex), to which a
remote controller (transmitter) has to be assigned should be put into the programming mode as provided
for in its programming mode instruction.
2. Remote controller assignment - HSR-1
Put the receiver (a
drive/external receiver) into
the programming mode, as
provided for in the manual .
Press the programming
button P2 (on the back)
twice.
Press the button UP once.The drive (roller blind) will move
UP/DOWN for a moment and/or
a receiver will emit a sound.
OK– First programming
performed correctly!
Check the operation by pressing UP/STOP/DOWN buttons.
When the drive moves in the opposite direction (the roller blind/drive moves down when the UP
button is pressed), restart the process and press the DOWN, not the UP button after pressing the
P2 button.
This way the drive direction is changed.

8
www.rojaflex.com
Programming and setup
Each time, the button must be pressed within 4 seconds!
Otherwise, the system will automatically leave the programming mode.
Check the operation by pressing UP/STOP/DOWN buttons.
When the drive moves in the opposite direction (the roller blind/drive moves down when the UP
button is pressed), restart the process and press the DOWN, not the UP button after pressing the
P2 button.
This way the drive direction is changed.
2.1 Remote controller assignment - HSR-5
By pressing the K2 or K1
button, select the required
channel (LED is lit).
Put the receiver (a
drive/external receiver)
into the programming
mode, as provided for in
the manual .
Press the programming
button P2
(on the back) twice.
Press the button UP once.
The drive (roller blind) will move UP/DOWN for a moment and/or the receiver will emit a sound.
OK– First programming performed correctly To assign
successive channels, repeat the entire procedure from the
start
When the group function is active (all LEDs are lit),
the channels cannot be assigned jointly or separately.
SI
P2
BI

9
www.rojaflex.com
Programming and setup
SI
P2
BI
SI
P2
BI
Further information is available in relevant operating manuals of Rojaflex drives and radio
receivers.
3. Adding the remote controller
E.g.: HSR-5
(does not apply to HSR-1)
Select the previously
programmed channel in the
ALREADY ASSIGNED
transmitter by pressing the
K1 (or K2) button.
Then in a NEWLY coded
transmitter, select a
channel that you want to
add, by pressing the K1 (or
K2) button (a LED is lit by
the selected channel).
On the previously
programmed remote
controller, press the
programming button P2 (on
the back) thrice.
Then in the currently
programmed remote
controller, press the
programming button P2
(on the back) once.
The drive (roller blind) will
move UP/DOWN for a
moment and/or the receiver
will emit a sound.
OK - the remote controller was
added.
Important: In the SI (Single-Direktional System / Single-directional communication) systems,
the P2 button of the already programmed remote controller is pressed only twice!
This applies to MLSF/MLMMF drives – and external receivers REHK-1 and RUE-UP.
An operating manual/drive of a given receiver/driver.

Notes
10
www.rojaflex.com

Notes
11
www.rojaflex.com

Any reproduction, including of parts of this document, requires the author’s consent.
Any changes in the
product which, in our opinion, improve its quality, can be made
at any time, without a previous communication or notification.
The illustrations are used as examples only, and can differ from the actual
appearance of the product.
We reserve the
right to errors. We shall not be held responsible for any printing
errors. Our General Commercial Terms and Conditions shall apply.
The current version of this operating manual can be found at:
www.rojaflex.com/bedienungsanleitungen.html
Should you have any
questions about our
product,
please, contact us by a letter
or by e
-mail
at the following address:
rojaflex®™ is a registered
trademark of Schoenberger
Germany Enterprises Gmbh & Co.
KG Zechstraße 1
–7
82069 Hohenschäftlarn
Germany
Phone [phone]