Roland JUPITER-X Manual

1
SOUND PACK/WAVE EXPANSION Install Manual
This manual explains how to import or install SOUND PACK and WAVE EXPANSION on the JUPITER-X/Xm.
Read this in conjunction with the JUPITER-X/Xm Owner’s Manual and Reference Manual (PDF).
Preparing the Sound Files
* If you’re using the USB flash drive for the first time, format it
using the JUPITER-X/Xm.
&“Formatting a USB Flash Drive” (Owner’s Manual)
1. Prepare the sound file that you will add on the
JUPITER-X/Xm, and place the file on your computer.
MEMO
Sound files such as SOUND PACK or WAVE EXPANSION can be
obtained via the Roland Cloud.
For more about Roland Cloud, refer to the Roland website.
&https://www.roland.com/
* Please be aware that in some countries or regions, it might not
be possible to use Roland Cloud at this time.
2. Connect the USB flash drive to your computer.
3. Save the file in the appropriate directory of your USB
flash drive.
SOUND PACK (extension: .SDZ): ROLAND/SOUND folder
WAVE EXPANSION (extension: .EXZ): Root directory
4. Disconnect the USB flash drive from your computer.
Adding the Sounds
Depending on the sounds that you are adding, perform the steps
described in “Importing a SOUND PACK” or “Installing a WAVE
EXPANSION” (p. 2).
Importing a SOUND PACK
1. Connect the USB flash drive in which you saved the
sound file to the JUPITER-X/Xm.
&“Preparing the Sound Files”(p. 1)
2. Press the [MENU] button.
3. Use the [1] knob or PAGE [ ] [ ] buttons to select
“UTILITY,” and then press the [ENTER] button.
4. Use the [1] knob or PAGE [ ] [ ] buttons to select
“IMPORT/EXPORT,” and then press the [ENTER] button.
5. Use the [1] knob to select “IMPORT TONE,”and then
press the [ENTER] button.
6. Use the [1] knob to select the file that contains the tones
that you want to import, and then press the PAGE [>]
button.
7. Use the [1] knob to select the tone that you want to
import, and then use the [2] knob to add a check mark.
MEMO
To select or de-select all tones, hold down the [SHIFT] button
and operate the [2] knob.
To select or de-select a specific range of tones, press the
[ENTER] button at the beginning of the range, then at the
end of the range, hold down the [SHIFT] button and press the
[ENTER] button.
8. Press the PAGE [>] button.
9. Use the [1] knob to select the import-destination tone,
and then press the [ENTER] button to add a check mark.
NOTE
5 Be aware that the import-destination tone you select will
be overwritten.
5 An “ * ” is displayed for tones used in scene.
5 If the import-destination has fewer tones than the import-
source, not all of the selected tones will be imported.
5 The number of tones is shown in the upper right of the
screen.
Number of import-destination/import-source tones
5 If there is a tone named “INIT TONE,” it is automatically
selected as the import-destination tone.
If you want to keep that tone, clear the check mark.
10. Press the PAGE [>] button.
A confirmation screen appears.
If you decide to cancel, press the [EXIT] button.
MEMO
The first time you import, the user license registration screen
appears.
To execute, use the PAGE [>] button to select “OK,”and then
press the [ENTER] button.
JUPITER-X/Xm
© 2020 Roland Corporation

2
SOUND PACK/WAVE EXPANSION Install Manual
11. To execute, use the PAGE [>] button to select “OK,” and
then press the [ENTER] button.
When import is completed, the message “Import Tone
Completed!” appears.
NOTE
Never turn off the power or disconnect the USB flash drive
during a process, such as while the“Processing…” display is
shown.
Installing a WAVE EXPANSION
1. While pressing the [ENTER] button, turn on the power.
The EXPANSION top screen appears.
Used capacity
EMPTY:
New files can be installed.
FULL:
New files cannot be installed.
In order to install, you must create
free space.
&“Uninstalling a WAVE EXPANSION”
(p. 2)
List of installed WAVE EXPANSION
to Uninstall
(PAGE [<] button)
to Install
(PAGE [>] button)
2. Press the PAGE [>] button to move to the installation
screen.
3. Use the PAGE [ ] [ ] buttons to select the file that you
want to install, and then press the PAGE [>] button.
A confirmation screen appears.
If you decide to cancel, press the [EXIT] button.
MEMO
The first time you install, the user license registration screen
appears.
To execute, use the PAGE [>] button to select “OK,”and then
press the [ENTER] button.
4. To execute , use the PAGE [>] button to select “OK,” and
then press the [ENTER] button.
Uninstalling a WAVE EXPANSION
If there is insufficient free memory space, uninstalling a previously
installed WAVE EXPANSION will let you install a new WAVE
EXPANSION.
1. While pressing the [ENTER] button, turn on the power.
The EXPANSION top screen appears.
2. Use the PAGE [ ] [ ] buttons to select the file that you
want to uninstall, and then press the PAGE [<] button to
move to the uninstallation screen.
A confirmation screen appears.
If you decide to cancel, press the [EXIT] button.
3. To execute, use the PAGE [>] button to select “OK,” and
then press the [ENTER] button.
User License
SOUND PACK and WAVE EXPANSION are associated with the user
licenses of the user who downloaded them.
SOUND PACK or WAVE EXPANSION that have differing user licenses
cannot be imported into the same JUPITER-X/Xm.
User A
EXZ002
User B
EXZ002
A B
User A
EXZ001
A
A
If you want to import or install SOUND PACK and WAVE
EXPANSION that has a different user license than what is already
registered to this JUPITER-X/Xm unit, you must initialize the user
licenses by performing the procedure described in“Initializing the
User Licenses While Preserving the User Data” (p. 3).
Initialize
User A
EXZ002
User B
EXZ002
A B
the Factory Settings
A

3
SOUND PACK/WAVE EXPANSION Install Manual
02
Initializing the User Licenses While
Preserving the User Data
If you’ve initialized the user licenses, you’ll be able to import or
install SOUND PACK and WAVE EXPANSION that you downloaded
using a new user license.
To initialize the user licenses, perform the steps described in
“Returning to the Factory Settings (FACTORY RESET).”
Returning to the Factory Settings (Factory Reset)
NOTE
5 Installed WAVE EXPANSION are deleted.
5 Never turn off the power or disconnect the USB flash drive
during a process, such as while the“Processing…” display is
shown.
1. Press the [MENU] button.
2. Use the [1] knob or PAGE [ ] [ ] buttons to select
“UTILITY,” and then press the [ENTER] button.
3. Use the [1] knob to select “FACTORY RESET,” and then
press the [ENTER] button.
The FACTORY RESET screen appears.
4. Use the cursor [ ] [ ] buttons to select the item, and
press the [ENTER] button to select/clear the check boxes
so that only the “Remove License”check box is selected.
* The “Remove License” check box is not displayed if a sound
pack or wave expansion has not been imported/installed.
* If you execute this with other check boxes besides“Remove
License” selected as well, the data corresponding to each
selected item is erased. See “Returning to the Factory Settings
(Factory Reset)” in the JUPITER-X/Xm Owner’s Manual for
details.
5. Press the cursor [>] button.
A confirmation message appears.
If you decide to cancel, press the [EXIT] button.
6. To execute, use the [2] knob to select “OK,” and then
press the [ENTER] button.
The display indicates“Completed. Turn off power.”
7. Turn the power of the JUPITER-X/Xm off and then on
again.
The user licenses are initialized.
Restoring Backup Data (RESTORE)
Here’s how user data that you backed-up on a USB flash drive can
be returned to the JUPITER-X/Xm. This operation is called “restore.”
1. Press the [MENU] button.
2. Use the [1] knob or PAGE [ ] [ ] buttons to select
“UTILITY,” and then press the [ENTER] button.
3. Use the [1] knob to select “RESTORE,” and then press the
[ENTER] button.
4. Use the [1] knob to select the file that you want to
restore.
5. Press the [ENTER] button.
A confirmation message appears.
If you decide to cancel, press the [EXIT] button.
6. To execute, use the [2] knob to select “OK,” and then
press the [ENTER] button.
When the restore operation is finished, the screen indicates
“Completed. Turn off power.”
7. Turn the power of the JUPITER-X/Xm off and then on
again.
Error Message
Message Action
Expansion File Not
Found!
This appears if the USB flash drive does not contain
a WAVE EXPANSION file.
Check that the file is correctly saved, and that the
file extension is “.exz.”
Incorrect File!
This appears if the selected sound file is not
compatible with the JUPITER-X/Xm, or if the file is
damaged.
Check the models that are listed as compatible
for the file you downloaded, and try downloading
again.
Incorrect License! Please
Remove License
This appears if the selected sound file is associated
with a different user license.
To install, you must either obtain a file that has the
same user license as the currently-installed sound
file, or initialize the user licenses.
Expansion Memory Full!
This appears if there is insufficient free space for
installation.
To install, you must uninstall a currently-installed to
create free space.
It has already been
installed
This appears if the selected file is already installed.
There is no need to reinstall.