ROLANSTAR CPT007-YW120-RR User manual

V12.0HEIGHT ADJUSTABLE DESK
CPT007-YW120-RR
CPT007-BK120-RR
CPT007-BO120-RR
[e-mail]

1

2

3

4

ACCESSORIES LIST
1
x2
2
x2
5
3
x1
4
x2
5
x2
6
x2
7-L
x1
14-L x1 14-R x1
7-R
x1
8
x1
9
x1 10 x1 11 x1
13 x1 12 x1
16 x1 17 x1 15 x1
120cm / 47.2in
53cm / 20.9in
60cm / 23.6in
120cm / 47.2in
55cm / 21.7in
8.8cm / 3.5in
20cm / 7.9in
25.7cm / 10.1in
56cm / 22in
8cm / 3.1in

A
x12+1
B
x8+1
C
x14+1
D
x10+1
E
x8+1
F
x4
G
x4
H
x4
I
x5
J
x4
K
x4
L
x12+2
M
x1
N
x1
O
x1
M8*10mm M8*35mm ST4.8*12mm
1/4*25mm
5*35mm 13*25mm
1/4*12mm
K5K4
6

1
1
2
2
34
4
5
6
EXPLODED
6
8x1 9x1
12
13
17
15
16
14-R
14-L
7-R
7-L
7
10

STEP 1
8
1
1
3
A
A
A
A
X8
A
K5
X1
N

9
STEP 2
STEP 3
X8
B
X4
J
A
A4
4
K
K
2J
JB
K5
X4
K
X1
N
X4
A
K5
X1
N

STEP 4
STEP 5
D
D
D
D
D
D
12
10
X6X1
D
K4
M
X14
C
8
5
C
9
10

11
STEP 6
Do not fully tighten
the screws yet
X4
G
×1
G
G
14-L
14-R
16
Note
Grooves downward
17

STEP 7
Do not fully tighten
the screws yet
X4
F
F
F
15
Tighten the screws
12
15

STEP 8
Fully tighten all the
screws
COMPLETE
13
7-L
14-R
Note
This part upward
Note
Push part 7
into part 14

STEP 9
X4X1
D
M
D
D
L
14
X4
L
12
7-R
Put Part L between Part 7
and 12 before screwing if the
contact surface is uneven

STEP 10
15
11
Plug In

STEP 11
X5
I
TIGHTEN
STICK
16

E
L
STEP 12
X8X4
E H
X1X8
M
H
H
E
E
K4
17
Fully tighten all the
screws
13
3.4cm / 1.3in
5.8cm / 2.3in
L

STEP 13
18
K
Adjust K to make the desk
steady

Desktop Height Memory Setting
POSITION SETTING: Can set up two memories. Adjust the desktop to the appropriate
height with ∧or ∨buttons. And then press "1 or 2" button, about 4 seconds until the
display flashes "S -1 or S-2 ", indicating that memory setting is successful.
LOCATION QUERY: In the run mode, press any of the 1 / 2 keys to flash the height of
the key memory.
POSITION REACHING: In the run mode, when the desktop stops, press any of the 1 /
2 keys twice to adjust to the desktop height of the key memory. When desktop is moving,
pressing any button can stop it.
OPERATION INSTRUCTIONS
Up / Down Button
Press the ∧to raise the desk, when you release the button it will stop. Press the ∨to
lower the desk, when you release the button it will stop. When pressing the ∧/ ∨, the
desk travels a very short distance, so that users can fine-tune the desk height according
to preference.
The Lowest Height Position Setting
POSITION SETTING: Please adjust the desktop to the appropriate height; and then
hold both "2" and "∨" button for 5 seconds; when the display appears "- d o", the
lowest height is memorized successfully. Once the desktop is dropped to its lowest
height position, the display shows "- L o".
POSITION CANCELLATION:
Option 1 - Refer to the initial setting process.
Option 2 - Adjust the desktop to the lowest height where the display shows
"- L o", hold both "2" and the down button for 5 seconds; at this time, the display will
show "- d o" indicating the set lowest height position has been successfully canceled.
The Highest Height Position Setting
POSITION SETTING: Please adjust the desktop to the appropriate height; and then
hold both "1" and the up button for 5 seconds; when the display appears "- u p", the high-
est height is memorized successfully. Once the desktop is raised to its highest height
position, the display shows "- h I".
POSITION CANCELLATION:
Option 1 - Refer to the initial setting process.
Option 2 - Adjust the desktop to the highest height where the display shows "- h I", hold
both "1" and the up button for 5 seconds; at this time, the display will show "- u p" indicat-
ing the set highest height position has been successfully canceled..
Initial Settings
（Under normal state, can be operated at any time; Or replace the controller for the first
time）
Press and hold both the ∧and ∨until the display appears " - - - ", release the keys,
then the tabletop will automatically move up and down. When the top stop moving, the
initial setting process succeeds.
Restore Factory Settings
When the display appears error code "rST" or "E16", press and hold the “V” button for 5
seconds until the display flashes " - - - "; release the key, then the adjustable desk legs
will automatically move down to its mechanical lowest point, and move up and stop at a
factory-preset position. Finally, the desk can work normally.
19