Romik 1619 User manual

REV 6 12 /02/ 21
Installation Instructions
Part No. 1619
Product: Running Boards
Application:
RAM ProMaster 2014+
Level of Difficulty: 1 2 3 4
5
Installation Time: 120 Min
Hardware
Torque Specifications
M6 Bolt
3 ft-lbs.
M8 Bolt
7 ft-lbs.
M10 Bolt
16 ft-lbs.
M12 Bolt
28 ft-lbs.
ATTENTION: Use correct torque settings to avoid
damaging the running boards and or mounting
brackets. Failure to do so will void your warranty.
If you have any questions please contact our technical
team at 1-866-717-6645
Driver’s Side
Pass Side
Front

Installation Instructions 1619 Bracket Kit
Important Install Tip: When installing Romik HTC inserts. Test by tugging on it before installing braket. Blue
loctite is highly recommended.
Make sure the HTC is seated correctly and do not use power tools as this will only spin the insert and possibly
damage it.
Step 1: Separate brackets and hardware as per 1st page of this installation manual. Please note bracket If you
are working on a short whell base reverse bracket #8 to the (last) 4th position and #9 to the 3rd position.
Step 2: Driver’s side front, remove factory rubber plugs as shown on Figure 1 TIP: Try to preassemble the
bracket for easier placement. Install provided HTC 243
Step 3: Bring pre-assembled bracket #1 and install onto M10 Wakaki and secure with supplied M10 bolts,
push clamp end onto the vehicle chassis lip push up and secure Figure 2. Do not tighten at this time since the
board will help level the bracket.
Step 4: Pre-assemble Driver’s rear bracket #2 as shown Figure 3 Install supplied M10 Wakaki as shown
M10 Wakaki
Figure 1
Figure 2
Figure 3

Installation Instructions 1619 Bracket Kit
Passenger Side note bracket positioning (Long wheel base shown)
Step 5: Install M10 wakaki insert as shown on Figure 4 bring pre-assembled passenger bracket and install do
not tighten. Raise section #10 onto vehicle “lip”using block #4 and M10 bolt secure together. Push section #10
as high as possible and tighten M10 + block #4 making sure #4 is offset as shown in Figure 5.
Step 6: Remove factory plugs as shown figure 6. Install M10 wakaki as shown on Figure 6.
Figure 4
Figure 5
Figure 6

Installation Instructions 1619 Bracket Kit
Step 7: Install bracket #7 and extra support #11 as shown below Figure 7 and 8. Do not tighten.
Step 8: NOTE: If you are working on a 136 WB please use bracket #9 Long wheel base bracket #8 should
be installed in the middle of the sliding door. Remove black rubber plugs and Install provided M10 Wakaki
inserts as shown on figure 9. Attach brackets using provided M10 hardware as shown below. Do not tighten
Figure 7
Figure 8
Figure 9

Installation Instructions 1619 Bracket Kit
Step 9: NOTE: If you are working on a 136 WB please use bracket #8 Long wheel base bracket #9 should
be installed towards the end of the sliding door. Remove black rubber plugs and Install provided M10 Wakaki
inserts as shown on figure 10. Attach brackets using provided M10 hardware as shown below. Do not tighten
Step 10: Once all the brackets are installed proceed and assemble the Romik “connect” running boards. Place
the boards on the brackets and tighten them to our torque specs. NOTE: if necessary, use a level to make sure
the running boards are properly installed.
Step 11:Review last page of this manual for running board install instructions and torque values
For Technical support please call our team at 1-866-717-6645 and one of our experts will assist
you with this installation..
Thank you for choosing Romik.
Figure 10

ROF / ROB / RPD 2 PC Romik Connect instructions
Please follow these steps to successfully “join”the 2 PC running boards together.
Step 1: Remove products from box and placed on a soft surface to avoid scratching.
Step 2: Remove plastic endcap as shown on Figure A1 –A4 keep screws as they will be re-used.
Step 3: Remove Romik Connect plate and assemble as show on Figure B1 –B3 using original screws.
Join two running boards together using supplied M8 bolts torque to 7 ft lbs.
Step 4: Install running boards as per last page of this manual.

Running Board Installation Instructions
NOTE: Use of power tools will damage the bottom of the
running board and void your warranty.
1) Flip your Romik running boards onto a flat surface, make sure to place the running boards on a
towel or cardboard in order to protect the surface Figure 1.
2) Loosen the M8 bolts on back of your running boards Figure 2. Depending on your model there
Will be either 6 or 8 bolts installed per side.
3) Once your brackets have been installed, place the running board onto the brackets as shown on
Figure 3.
4) Adjust running boards, centering on vehicle. Hand tight M8 hardware on running boards.
5) Follow the torque procedures, torque M8 hardware to 7 ft-lbs using a torque wrench.
6) Cleaning and maintaining your running boards is important, apply a light coat of a quality
carnauba wax at least 2X per year. Wash often with mild soap and make sure to remove all soap
Residue. Many car automatic carwashes use a strong soap, make sure to use enough water to
remove all residue.
7) Register your products at https://romik.com/productregistration
8) Warranty information at www.Romik.com/warranty