Romotop IMPRESSION 2G 42.60.01 User manual

EN DE
FR IT
ver.2020.09
ROMOTOP spol. s r.o.
742 01 Suchdol nad Odrou
Czech Republic
www.romotop.com
2G 42.60.01

ROMOTOP spol. s r.o., issued on 1 November 2017 Revised Nov 2017 ROMOTOP GmbH, herausgegeben am 01.11.2017 Revision 11/17
DE
EN
Product sheet under Regulation EU 2015/1186
Supplier's name or trademark: Romotop spol. s r. o.
Supplier's model identifier: Impression 2G 42.60.01
The energy efficiency class of the model: A
The direct heat output in (kW): 7,0
The indirect heat output in (kW): 0
The energy efficiency index EEI: 106,1
The useful energy efficiency at nominal heat output (%): 80,1
The useful energy efficiency at minimum load (%): Pass
Special requirements (instalation, maintanance): See instructions
The information in the product sheet of the local space heater shall be provided in the
following order and shall be included in the product brochure or other literature provided
with the product.
EU 2015/1186
Name oder Warenzeichen des Lieferanten: Romotop GmbH
Modellkennung des Lieferanten: Impression 2G 42.60.01
Energieeffizienzklasse des Modells: A
D (kW): 7,0
I (kW): 0
Energieeffizienzindex EEI: 106,1
(%): 80,1
Energieeffizienz bei Mindestlast (%): Pass
Besonderen Vorkehrungen (bei der Installation oder Wartung): siehe Anleitung
bereitgestellte Unterlagen aufzunehmen.

ROMOTOP S.A.R.L., 1/17 ROMOTOP spol. s r.o., rilasciato il 01.11.2017 Revisione 11/17
IT
FR
EU 2015/1186
Le nom du fournisseur ou la marque commerciale: Romotop S.A.R.L.
L : Impression 2G 42.60.01
L : A
La puissance thermique directe en (kW): 7,0
La puissance thermique indirecte en (kW): 0
L EEI: 106,1
L (%): 80,1
L (%): Pass
Mesures s : Cf. instructions
- ut
autre document fourni avec celui-ci.
Scheda prodotto secondo normativa EU 2015/1186
Nome oppure oppure marchio del fornitore: Romotop spol. s r. o.
Codice prodotto del fornitore: Impression 2G 42.60.01
classe di efficienza energetica del modello: A
potenza termica diretta in (kW): 7,0
potenza termica indiretta in (kW): 0
indice di efficienza prodotto EEI: 106,1
efficienza del combustibile con potenza termica nominale (%): 80,1
efficienza del combustibile con carico minimo (%): Pass
precauzioni speciali ( ): Vedi introduzione
da indicare nella seguente successione e da inserire nel depliant o qualsiasi altro catalogo in
riferimento al prodotto.

EN DE FR IT
Product name Produktbezeichnung Nom du produit Nome del prodotto IMPRESSION
2G 42.60.01
Dimensions HxWxD (mm) Abmessungen HxBxT (mm) Dimensions HxLxP (mm) Dimensioni AxLxP (mm) 1316 x 598 x 447
Weight (kg) Gewicht (kg) Poids (kg) Peso (kg) 100
Completed legislation Abgeschlossene
Gesetzgebung Legislazione completata -
EN 13 229 / 15a B-VG / DIN plus / BImSch V 2
Eco-design (%) (%) -conception (%) Eco-design (%) 70,1
EEI EEI EEI EEI 106,1
Energy Label Energielabel Etichetta energetica A
Prescribed fuel Vorgeschriebener Brennstoff Combustible prescrit Combustibile prescritto Piece wood /
Morceau de bois / Pezzo
di legno
Fuel length (mm) (mm) Longueur de carburant (mm) Lunghezza del carburante
(mm) 250
Average wood consumption (kg/h)
Durchschnittlicher
Holzverbrauch (kg(h) Consommation de bois moyenne (kg/h) Consumo medio di legna (kg/ora) 2,04
Max. allowed wood batch (kg/h) Max. erlaubte Holzzuladung
(kg/h) Dose de
Dose massima di legna
consentita (kg/ora) 2,7
Fuel supply interval for the rated
output
Zeitabstand der
Nennleistung pour la puissance nominale
Intervallo fornitura
combustibile per potenza
nominale
1. hour, Stunde, heure,
ora
The greatest height of the filling
1/3 of the firebox Hauteur maximale de la charge 1/3 de la hauteur du foyer Altezza massima caricamento 1/3 -
Fuel delivery method Art der Brennstoffbeschickung combustibile
manually, von Hand,
manuellement,
manualmente
Amount of combustion air (m3/h) Menge an Verbrennungsluft
(m3/h) (m3/h) (m3/h) 25,9
Nominal heat output (kW) (kW) Puissance nominale (kW) Potenza nominale (kW) 7,0
Total regulated output (kW) Reg. Gesamtleistung (kW) Potenza totale regolata (kW) 3,5 9,1
Efficiency (%) Wirkungsgrad (%) Rendement (%) Efficienza (%) 80,1
Mass flow rate of dry flue gases
(g/s) Massendurchfluss der trockenen Abgase (g/s) combustion secs (g/s)
Flusso peso combustibile secco
(g/s) 7,2
Average flue-gas temperature
Durchschnittliche Temperatura media gas
232
Average flue gas temperature after
Flue pipe
Durchschnittliche
Abgastemperatur hinter dem
tubulure
Temperatura media gas
272
Flue draught (Pa) (Pa) (Pa) Tiraggio del camino (Pa) 11
Ceramic accumulation system /
Keramisches Zugsystem / /
Sistema di accumulo di ceramica
Accumulation rings /
Aufsatzspeicher
Set Ringe /
Anneaux de l'ensemble de
rangement des accessoires / Set di
archiviazione degli attacchi Anelli
Minimum radiant area / Mindest- /
Surface radiante minimale / Area radiante minima 4,0 ---
Maximal load of wood / Maximal Brennstoff- /
Charge maximale
du bois / Carico massimo di legno kg 4,9 ---
Total heat output of the fireplace chamber / Feuerungsleistung / Puissance
thermique totale de la chambre du foyer / Potenza termica totale della
camera del camino kW 16,0 ---
Average flue gas temperature (upper deflector removal) / Durchschnittliche
Rauchgastemperatur (Entfernen des oberen Deflektors) /
/ Temperatura media
dei gas di scarico (rimozione del deflettore superiore)
404 ---
Radiant surrounds without convection grids from a material with minimal thermal conductivity
Circondamenti radianti senza griglie di convezione
The fireplace insert is suitable for use in radiant fireplaces without convection grilles if the stove rules and regulations are followed.
Der Kamineinsatz ist unter Einhaltung der Kamin sanlagen ohne Konvektionsgitter geeignet. .
L'inserto per ianti senza griglie di convezione, a condizione che vengano rispettate le regole della stufa.
EN DE FR IT
Dust at O2 = 13%
(mg/Nm3) Staub bei O2= 13 % (mg/Nm3) 2= 13% (mg/Nm3) 2= 13 % (mg/Nm3) 19
The concentration of CO
in the flue
gases at O2= 13% (mg/Nm3)
CO Konzentration in den
Abgasen bei O2= 13%
(mg/Nm3)
Concentration en CO dans les
2=
13% (mg/Nm3)
Concentrazione CO nei gas
comburenti
2
= 13 % (mg/Nm3) 912
The concentration of CO
in the flue gases
at O
2
= 13% (%)
CO Konzentration
in den Abgasen
bei O
2
= 13% (%)
Concentration en CO dans les
2=
13% (%)
Concentrazione CO
nei gas comburenti
2
= 13 % (%) 0,0729
CO2 (%) CO2 (%) CO2 (%) CO2 (%) 8,69
OGC - 02=13% (mg/m3) OGC - 02=13% (mg/m3) OGC - 02=13% (mg/m3) OGC - 02=13% (mg/m3) 42
NOx - 02=13% (mg/m3) NOx - 02=13% (mg/m3) NOx - 02=13% (mg/m3) NOx - 02=13% (mg/m3) 115
Connection height for rear
installation (mm) (mm) Hauteur de raccordement pour (mm) Altezza di collegamento per l'installazione posteriore (mm)
1161
Flue pipe diameter (mm) Rauchabfuhrdurchmesser (mm)
(mm) Diametro del condotto fumi (mm) 150 - 160
Flue throat (mm) Flue Hals (mm) Flue la gorge (mm) Fumi gola (mm) 160
CAI diameter (mm) CPV-Durchmesser (mm) Diametro ACA (mm) 125
Dimensions of the combustion
chamber HxWxD
(mm)
HxBxT
(mm) Dimensions de la chambre de combustion HxLxP
(mm)
Dimensioni della camera di
combustione AxLxP
(mm)
472 x 349 x 237
Dimensions of the furnace
door HxWxD
(mm)
HxBxT
(mm) Dimensions de la porte du four HxLxP
(mm)
Dimensioni della porta del
forno AxLxP
(mm)
556 x 379
Min. cross section of convect air
inlet for nominal output
(cm2)
Min. Querschnitt der
Konvektionsluftzufuhr f. die
Nennleistung
(cm2)
convection pour rendement
nominal
(cm2)
Sezione minima
convezione per la potenza
nominale (cm2)
500
Min. cross section of convect air
outlet for nominal output
(cm2)
Min. Querschnitt des
Konvektionsluftausgangs f. die
Nennleistung (cm2)
convection pour rendement
nominal
(cm2)
aria di convezione per la
potenza nominale (cm2) 700
Door design
(Right=1 / Left=2 / Sliding =3) (Rechts=1/Links=2/Schieben
=3)
(
Droite=1 /
Gauche=2 / Coulissant = 3)
Versione dello sportello
(Destra=1 / Sinistra=2 /
estraibile = 3) 2
Back door design (No=0 /
Right=1
/ Left=2 / Sliding =3)
(Nein=0 /
Rechts=1 / Links=2 / Schieben
= 3)
(Non =0 / Droite=1 / Gauche=2 /
Coulissant = 3)
Design della porta posteriore
(No=0 / Destra=1 / Sinistra=2
/
estraibile = 3) 0
Distance from flammable
materials Abstand von Brennstoffen Eloignement des Distanza da materiali infiammabili
Side (mm)
Side with glass (mm) (mm) Seitenglas (mm) (mm) (mm) Laterali (mm) Vetro laterale (mm) X 500
-
Back (mm) Hinterwand (mm) (mm) Posteriore (mm) Z 800
Front (mm) Frontwand (mm) Frontale (mm) Anteriore (mm) Y1000
From the ceiling (mm) Von der Decke (mm) Du plafond (mm) Dal soffitto (mm) V1000
Supplied accessories Accessoires fournis Accessori forniti
Protective glove
yes=1 / no=2 Schutzhandschuh ja=1 / nein=2 Gant de protection oui=1 / non=2 Guanto protettivo 1
Hook to open the ashtray
yes=1 / no=2
Haken um den Aschenbecher
ja=1 / nein=2
Crochet pour ouvrir le cendrier
oui=1 / non=2
Agganciare per aprire il
posacenere
2
Ashtray
yes=1 / no=2 Aschenbecher
ja=1 / nein=2 Cendrier oui=1 / non=2 Portacenere 2
Chimney brush
yes=1 / no=2 ja=1 / nein=2 oui=1 / non=2 Spazzola camino 2
Automatic
ventilation valve
yes=1 / no=2
Automatisches
ja=1 / nein=2
oui=1 / non=2
Valvola di scarico automatica
2
Cooling loop
yes=1 / no=2 Thermischen Ablaufsicherung ja=1 / nein=2 Boucle de refroidissement oui=1 / non=2 Ciclo di raffreddamento 2
Cooling valve
yes=1 / no=2 ja=1 / nein=2 Vanne de refroidissement oui=1 / non=2 Valvola di raffreddamento 2
Cover with insulation
yes=1 / no=2 Abdeckung mit Isolierung ja=1 / nein=2 Couvert avec isolation oui=1 / non=2 Copertura con isolamento 2
Technical Sheet, Technisches Datenblatt, Fiche technique, Scheda tecnica Technical Sheet, Technisches Datenblatt, Fiche technique, Scheda tecnica

Air regulation, Luftregulierung, R Regolazione aria
Dimension sketch, Croquis des dimensions, Dimensioni ingombro
Description EN: Beschreibung DE: Description FR : Descrizione IT:
A mm Installation space L'espace d'installation Dimensioni costruzione
B 160 mm Flue throat Flue Hals Flue la gorge Fumi gola
C mm CAI inlet CPV-Eingang Ingresso ACA
D 1 + 2 Air regulation Luftregulierung R Regolazione aria
E mm Frame Rahmen Cadre Cornice
Chamotte chamber, Schamottkammer, Camera chamotte
EN Procedure for exchange of chamottes:
1. Pull out the ceiling fireclay plat 1,2
2. Pull out the side fireclay plates - 3
3. Pull out the bottom fireclay plates - 5
4. Pull out the rear fireclay plates - 4
5. Use the reverse order for re-assembly
Note: Cracks in the chamotte do not have any effect on the
combustion and service life of the stove. The chamottes
should not remain crumbled to the metal for prolonged
periods of time.
Warning: When stoking logs, make sure they do not hit the
chamottes hard to prevent damage!
DE -
1. Decken Schamottplatte herausziehen 1,2
2. Seitenschamottplatten herausziehen - 3
3. Untere Schamottplatten herausziehen - 5
4. Hintere Schamottplatten herausziehen - 4
5. Wiedereinbau in umgekehrter Reihenfolge
Bemerkung: Ein einzelner Sprung hat keinen Einfluss auf das
Brennverhalten sowie die Haltbarkeit des Ofens Die
ollten nicht langzeitig bis auf das Blech
Hinweis: Beim Zulegen mit den Holzscheiten nicht heftig an
FR - :
1. 1,2
2. S - 3
3. -5
4. -4
5. M
Remarque :
Avertissement :
frappent pas brusquement les chamottes, cela les abimerait !
IT Procedimento per la sostituzione dello chamotte
1. Estrarre gli chamotte superiore 1,2
2. Estrarre gli chamotte laterali - 3
3. Estrarre gli chamotte sul fondo - 5
4. Estrarre gli chamotte posteriori - 4
5.
Nota: Le eventuali screpolature dello chamotte non hanno alcuna
Si
consiglia di non lasciare gli chamotte a lungo sgretolati fino alla
lamiera.
Avvertimento: I pezzi di legno vanno applicati in modo tale da
non farli urtare bruscamente contro lo chamotte, per evitare
conseguenti danneggiamenti!

EN General installation and operation manual
for Romotop fireplace inserts
- valid in general for all types of fireplace inserts manufactured by Romotop spol. s.r.o.
The attached technical sheet lists detailed technical data for each type of fireplace insert.
Installation of fireplace inserts may only be done by reseller authorized by Romotop spol. s r. o. .
The fireplace inserts may only be operated in accordance with this manual!
No unauthorized changes may be performed on the fireplace inserts!
1. Introduction
2. Technical description
3. Safety regulations
3.1 Safe distances
3.1.1 Safe distance of fireplace inserts from flammable materials
3.1.2 Safe distance of flue pipes from flammable materials and building constructions
3.2 Floor protection
3.3 Chimney fire prevention measures
4. Assembly regulations
4.1 General
4.2 Chimney connection
4.3 Enclosure of fireplace inserts
5. Operation manual
5.1 Fuel
5.2 Starting the fireplace insert for the first time
5.3 Kindling and firing
5.4 Stoking fuel
5.5 Operation during the transition period
5.6 Ash removal
6. Cleaning and maintenance
6.1 Cleaning the glass
6.2 Cleaning the fireplace inserts / disassembly of chamotte
6.3 Cleaning the chimney
7. Disposal of covers and the discarded product
8. Warranty
1. Introduction
Thank you for purchasing our fireplace insert and congratulations for becoming the owners of top-notch
fireplace inserts by Romotop spol. s.r.o., one of the forefront European manufacturers of fireplace heaters.
Our fireplace inserts can function as additional heating to augment the atmosphere of your home or
recreational building or as the main source of environmentally-friendly heating with high heat output, dust-free
operation and perfect combustion. All fireplace heaters produced by our company are tested in accordance with
3 240/2002 or 229/2002.
Please read through the manual and technical sheet thoroughly. The user is obliged to get properly acquainted
with proper installation and operation of this device with regards to its safe operation. Please keep the manual
and technical sheet so that you can brush up all the information necessary for the correct operation of your
fireplace insert before each heating season.
We only provide a warranty on our products if all the instructions listed in this operation manual are adhered to.
2. Technical description
Fireplace inserts are intended for building into stoves in various interiors (apartments, recreation buildings,
restaurants). Romotop spol. s.r.o. fireplace inserts are manufactured from quality construction materials cast
metal, CORTEN steel and quality construction and fittings steel, with stressed parts made of HARDOX steel.
The surface of steel constructions is protected by a refractory opaque paint. Refractory paints are not anti-
corrosive. The combustion chamber of full-plate fireplace inserts is padded by removable chamotte desks, which
are not connected by any paste material to prevent damage by heat dilatation. The combustion chamber can be
firmly closed by doors with special heat-resistant glass. The glass not only increases the aesthetics of the
flickering flames, but also facilitates pleasant heat radiation. The glass also prevents the sparks from the burning
wood and smoke from entering the room. The floor of the combustion chamber is usually equipped with a
removable cast-iron grate. Usually, a barrier, or alternatively a sheet metal or ceramic mould, is placed in front
of the grate to prevent the fuel falling and sliding onto the doors (front window). Grate fireplaces include room
for an ashpan under the grate. Some types allow custom-configuration of the flue pipe throat for top- or back-
side exhaustion. Some types of fireplace inserts have a rotary exhaust flue pipe throat. The fireplace insert
design may include a single coating or be supplemented with an external coat of zinc-coated sheet metal with
outlets for connection to the heat system. Installation of a support fan is recommended for vertical heat pipes
longer than 4m.
Fireplace inserts equipped with a separate intake of primary and secondary combustion air include the
appropriate control elements. The primary air is taken to the burning fuel (usually through the ashpan and grate)
and is used for primary combustion. The secondary air supports combustion of residual combustible gases in the
exhaust, increasing the output of the heater and significantly reduces the amount of pollutants escaping into the
atmosphere. The secondary air is mostly taken to the area above the burning fuel. Its presence causes the cold
air to roll around the inner side of the front glass. This process simultaneously prevents the blackening of the
front glass. The secondary air also participates in the primary combustion process when the primary air intake is
partially or completely sealed. Keep the primary air intake fully open at the beginning of the combustion
process, when the chimney draft is still weak. After the chimney heats up, you can partially or even completely
close the primary air intake, based on the target output of the fireplace insert. It is also possible to reduce the
fueling or limit the chimney draft by attaching a smoke shutter (a manual shutter in the flue pipe limiting the air
intake to at most 75%) to reduce the output of the fireplace insert. This is recommended especially for chimney
draft around and above 20Pa. The secondary damper is intended to fully close the stove when it is not in
operation. The fireplace and ashpan covers must always be closed except for starting operation, adding fuel and
removing solid combustion remnants to prevent exhausts entering the room.
It is possible to install heat and accumulation exchangers behind certain fireplace inserts, increasing the
efficiency of the whole stove and maximally utilizing fuel energy. Heat exchangers can be built into certain
types of fireplace inserts, in which case the production of warm service water also utilizes the double external
cover of the fireplace insert.
Some fireplace inserts are manufactured with a external air intake (EAI). This allows air to flow into the
combustion chamber in the fireplace insert from the exterior*, halls, technical rooms etc. Fireplace inserts with a
EAI are not dependant on the amount of air in the heated area. Thus, they not only contribute to a pleasant
atmosphere in your home, but also reduce energy expenses (since heated air already in the room is not

consumed). When installing the External air intake (EAI) outlet to the wall, it is important to make sure that the
pipe runs at a negative angle from the product. EAI lines must be isolated.
Fireplace inserts with a EAI are very convenient for stoves in low-energy houses. It is also possible to equip
the heating system of some fireplace inserts with EAI with electronic combustion regulation to increase
comfort. This can additionally increase the combustion process and stoking intervals, increase operation safety
and prevent uneconomic heating and over-heating of fireplace inserts (the shutter of the central air intake is
controlled by a control unit and servomotor in relation to the current combustion phase and output exhaust
temperature).
Warning: The fireplace inserts are not manufactured to provide continual heating and are intended for
periodic interrupted operation, mostly due to the need to empty the ashpan when the ash has cooled down.
*When connecting to an external air intake (from the outside), it is recommended to install double-acting flap
with a silicone cuff with possibility of closing air intake. This will prevent corrosion due to moisture
condensation when the product is not in use. The warranty does not cover damage caused by corrosion!
Attention, care must be taken to ensure that the damper is always open when the product is in operation!
3. Safety regulations
The fireplace inserts may be used in normal environments in accordance with -1 ed.2/2009. In
case of change of environment that could cause a temporary danger of fire or explosion (e.g. gluing linoleum,
PVC, working with paints, etc), the fireplace insert must be put out of operation in time, i.e. before the
occurrence of the dangerous situation. Furthermore, the fireplace inserts can be used only after the room is
thoroughly aired, preferably by wind draft.
A supply of sufficient amount of combustion air and room ventilation air must be ensured when the fireplace
stoves are in operation, especially with another heat device running simultaneously (approx. 8to 15 m3for
burning 1 kg of fuel)! When doors and windows are tightly sealed, this might not be the case! This is solved by
a CAI connected into a separate room. The regulation grate for combustion, ventilation and heating air must not
be obstructed. When stoking fuel, always open the door very slowly. You will prevent smoke and ash from
escaping into the room. The fireplace inserts require casual attendance and inspection.
Flammable fuels must not be used for stoking or heating! In addition, burning plastic material of any kind,
wood materials with various chemical bonding agents (chipboards, etc) or unsorted domestic waste with
remaining plastics is prohibited by law no. 201/20212.
Make sure to prevent children from handling the fireplace insert during heating. The fireplace insert
may only be operated by an adult person!
During heating all handles and knobs must be operated using a pair of tongs, hook or by a hand protected by
a glove (pot-holder) - there's a danger of burns! Objects made from flammable materials that could be set on fire
must not be stored on the fireplace inserts during operation and while hot. Please pay special attention when
handling the ashpan and when removing hot ash due to danger of burns! The hot ash must not get in contact
with flammable objects - e.g. when throwing in communal waste containers.
When the fireplace insert is used only seasonally and with unfavorable draft or weather conditions, special
attention must be paid when putting the stove into operation. When the fireplace stove is not in operation for a
longer period of time, the flue ways must be checked for obstructions before further operation.
The appropriate safety regulations for fireplace insert operation and installation must be adhered to in
accordance with
3.1 Safe distance:
3.1.1 Safe distance of fireplace inserts from flammable materials
When installing the fireplace insert in a place containing flammable materials belonging to class B, C and D,
the required safe distance in accordance with is 80cm from doors and 40cm in other
directions (see Figure 1), for fireplace inserts with double coating this amounts to 20cm. When installing the
insert in a place containing flammable materials belonging to class E or F, the distance must be doubled.
Information on the degree of flammability of certain building materials is listed in 501-1+A1/2010
and . When the prescribed safe distance of the heater from the flammable materials cannot be
kept, it is necessary to use a protective screen according to
Building materials sorted based on their reactivity with fire
A1 or A2
B akumin, Heraklith, Lignos, Ita
C
D
E or F
3.1.2 Safe distance of chimneys from flammable materials and building constructions
The safe distance from door case covers and similarly located building constructions from flammable
materials and from pipeline installation including its insulation is at least 20cm. The safe distance from other
flammable parts of the building construction at least 40cm (see fig.2) according to . This
includes building materials belonging to classes B, C and D as defined in -1+A1/2010 (see table
no.1) The same applies for walls and especially ceilings with plaster on a flammable surface, e.g. crates, planks,
etc.! When the prescribed safe distances cannot be kept, the danger of fire must be prevented through
construction solutions, non-flammable applications, heat-resistant insulations or protection screens.
3.2 Floor protection
Unless the fireplace is installed on a 100% non-flammable floor, it is necessary to place it on a non-flammable
insulation mat, e.g. metal plate (at least 2mm thick), ceramics, hardened glass, stone, in order to prevent the
flammable floor to exceed a temperature of during operation in accordance with 4.
According to 5.1.3.3 of the insulation mat must exceed the fireplace by at least
-80cm in the vertical direction from the insert stoking door.
-40cm in the horizontal direction from the insert stoking door.

Items made of flammable materials may not be placed on top of or at a less-than-safe distance from the
fireplace insert.
3.3 Chimney fire prevention measures:
Ordinary operation, especially with humid fuel, leads to the settling of ash and tar in the chimney. Neglecting
regular checking and cleaning of the chimney in accordance with the government regulation no. 34/2016
Coll. from 22st January 2016 increases the danger of fire.
In case of ash or tar catching fire in the chimney, please follow this procedure:
- do not under any circumstances extinguish the fire with water as it would create an abnormal amount of
steam and subsequently rip the chimney open
- if possible, the combustion chamber should be covered with dry sand, which will extinguish the fire
- close all intakes of air for combustion; if possible, cover the chimney. However, the smoke must not
accumulate back in the house
- contact your nearest fire fighting brigade to assess the situation and the necessity to report it as a fire
fighting emergency
- do not leave the house until the chimney is burned up; regularly check the chimney temperature and the
course of combustion
- contact a chimney service before starting a new fire in the stove to assess the state of the chimney and also
contact the manufacturer of the fireplace insert for inspection.
4. Assembly regulations
Warning: All local regulations, including regulations concerning national and European standards for
this type of appliances, must be adhered to:
- Fireplaces with open and closable furnace
- Built-in heating appliances and open fire inserts for solid fuel
- Room heaters fired by solid fuel
.2 - Chimneys and connecting flue pipes - Design, construction and installation of
heating appliances
- Chimneys General requirements
-1+A1/2010 - Fire classification of construction products and building elements
/1997 - Fire protection of heating appliances
Decree No. 268/2011 Coll. - Technical conditions of fire protection of buildings
4.1 General
The fireplace insert must be installed on the appropriate stand supplied by the manufacturer or on a brick
pedestal on floors with an appropriate load capacity. In case of fireplace inserts with an enclosure, it is necessary
to also consider the weight of the enclosure! If the existing arrangement does not meet this basic requirement,
necessary steps must be taken (e.g. using a mat for distributing the load). Make sure that there is enough space
for cleaning the fireplace insert, connecting flue pipes and the chimney unless the chimney can be cleaned from
other place, e.g. a roof or through doors designed for this purpose.
4.2 Chimney connection
Before assembling the closed fireplace insert it is necessary to calculate that the chimney construction will be
suitable for the installed fireplace insert nominal output as far as design, vent size and effective height are
concerned.
A suitable chimney (minimum profile, chimney draft, tightness, etc.) is a basic condition for the proper
functioning of the fireplace inserts. You should therefore contact a chimney sweeper before installing the
fireplace insert. Chimney values are included in the attached technical sheet. A smoke shutter or a draft
regulator should be installed for chimneys with too strong a draft. Such a draft can cause problems during
operation, e.g. intensive burning, high fuel consumption and can also lead to permanent damage of the fireplace
insert.
The minimum effective height of the chimney for exhaust gas from the insert is 5m (measured from the hoop
to the chimney mouth). The chimney entry must be equipped with a chimney hoop. Consult the vent connection
with the vent manufacturer. The vents must lead at least 5cm below the lower ceiling. Connect the flue mouth
with the chimney in the shortest possible way so that the flue length is at most 1/4 of the effective height of the
chimney (i.e. 1.5m). Connect the flue tube and the knee together with an overlap in such a way that the
connections always agree with the exhaust gas flow, or abut using the connection rings. If the connecting piece
passes through construction elements with flammable materials, it is necessary to use protective measures in
accordance with . The norm states that the flue pipe needs to rise to the vents in the direction
of exhaust flow with a degree of at least . The tightness and firmness of the joints is crucial. The chimney and
stove connection must adhere to SN 73 4201/2016 ed.2. The casing of the chimney must not exceed a
temperature of during the highest operation temperature of the stove. The cross section of the flue pipe
vents must not be larger than the cross section of the chimney vent and it must not narrow down in the direction
of the chimney. If calculations show that the cross section of the flue pipe and chimney vent could be smaller
than the cross section of the exhaust throat of the fireplace insert, the cross section of the flue pipes will be
lowered immediately behind the exhaust throat of the fireplace insert, either gradually or at a discrete point. The
flexible flue pipe from the materials in accordance with table A.1. may only used in places where it may be
checked in accordance with 7.2.1 SN 73 4201/2016 ed.2, and unless the flue pipe leads through an open air its
checkability must be ensured in accordance with 7.2.5 . A vertical flue pipe may only be
used in the cases listed in 8.3.4 and 8.3.5 .
The fireplace insert may be connected to a shared vent with a gas appliance for multi-layer chimneys in
accordance with SN 73 4201/2016 ed.2.
Leakage of water into the product when using a vertical flue with a chimney function is not a reason
for a complaint!
4.3 Enclosure of fireplace inserts
Special expertise is required for building the fireplace insert into the fireplace. Fireplace construction is
adjusted by norm . Installation of fireplace inserts may only be done by reseller
authorized by Romotop spol. s r. o..
When installing and installing a fireplace insert, follow these guidelines:
1. All security and construction regulations listed above must be followed.
2. After installing the whole fireplace, the inlet and outlet of conventional air through any construction
parts must not be limited. The cross section of the inlet and outlet of convect air is listed in the technical
sheet.
3. To augment the final appearance of the fireplace, the dimensions of the door frames exactly match the
ceramic facing produced by Romotop spol. s.r.o.
4. The enclosure must be made of suitable, designated materials.
5. The warm conventional air outlet must be at least 30cm below the ceiling (figure 2).
6. An inflammable ceiling construction must be present above the conventional warm air outlet. Its
temperature must not exceed . Thus, the lower ceiling must be insulated from the effects of heat coming
from the fireplace by a barrier and at least one not fully closeable grated opening (figure 2) or a sufficient
layer of heat insulation.
7. The same requirements also hold for the walls next to the fireplace and for the floor. A ventilated air
space must remain between the heat insulation and the wall. It is recommended to glue aluminum sheets on
the surface of walls.
8. The wall of the fireplace must not contain electric wiring and water or gas distribution pipes. The wall
nor its surface may contain flammable materials or materials which may release harmful substances when
heated.
9. Minimal free distances must be kept between the fireplace insert and the cover (see technical sheet) for
the whole height and width of the fireplace insert, so that convect air can freely circulate and prevent the

overheating of the fireplace set.
10. Eventual air conditioning piping must be located at least 40 cm from flammable building constructions,
or it must be documented that the heat from the piping cannot cause the construction to catch on fire. Convect
air can reach temperatures of up to near the insert!
11. Do not forget that fireplace inserts also spread heat in the direction of the floor. The floor under the
fireplace and at a distance of at least 80cm in front of the furnace and 40cm to the sides of the furnace must
be made of an inflammable material. The distance is measured from the closer edge of the furnace. The
surface for the fireplace must have an appropriate load capacity.
12. Do not forget that when considering the use of wooden decorative ledges, these must be made of quality
wood with a humidity of at most 15% and that convect cooling air must flow around it with a gap of at least
1cm or they must be heat-insulated from the fireplace, so that their surface temperature does not exceed
13. When distributing hot air via natural air circulation, it is recommended to use horizontal pipes at most
4m long. When distributing hot air via forced air circulation, the length of pipes is not limited.
14. The pipes for distributing hot air must be tight and made of a material resistant to operating
temperatures. We recommend insulating them at the whole length, especially where they traverse walls,
ceilings or around flammable materials.
15. Hot air outlets must not be located at areas with materials susceptible to structural changes caused by
temperature fluctuations (e.g. polyester lining, certain types of wallpapers etc.)
16. No construction changes or adjustments may be performed on the fireplace insert!!!
All local regulations, including regulations concerning national and European standards. Have a specialized
project elaborated before construction.
The project documentation must be elaborated in a scale of 1:10 or 1:20. Before the fireplace enters
operation, it must be inspected by a chimney sweeper and the exhaust path must be inspected in accordance with
Chapter 9 of . Inspection of the flue pipe connection to the insert and chimney vents
should be performed before closing the exhaust path to the hot air chamber. The result of the inspection shall be
recorded in the exhaust gas inspection report including the technical report according to Decree No. 34/2016
Coll. Please keep the Revision Report and the Technical Report carefully!
Vertical cross section of single-coating fireplace with closable furnace
01 chimney vent
02 wall
03 insulation area above the chamber
04 hot air chamber ceiling
05 ventilated air gap
06 heat insulating layer
07 hot air chamber area
08 fireplace insert flue pipe
09 fireplace insert smoke chamber
10 closed fireplace furnace
11 air intake from other rooms (or CAI)
12 ventilation of ceiling insulation areas
13 hot air outlet from the chamber
14 heat insulating layer
15 - wall of hot air chamber
16 fireplace ledge
17 fireplace ledge protection
18 air intake for hot air chamber
19 air intake from the room to under the fireplace insert
20 inflammable floor (pad) in front of the fireplace
21 CAI throat
Figure 2
A chart of the fireplace set holds in general also for double-coating fireplace inserts and fireplace inserts with
a heat-accumulating and warm water exchanger.
5. Operation manual
5.1 Fuel
It is only allowed to burn wood in fireplace inserts in accordance with law No. 201/2012 Coll.. To reach the
nominal parameters of the heater, we recommend using dry logs with a diameter of 5-8 cm and length of 20-30
cm and with a humidity below 20% (ideally 10%). Oven wood and chopped pieces of wood should be used
only when starting the fire. Recommended humidity can be obtained by storing the chopped logs for at least two
years in a ventilated shelter.
The fireplace insert should be heated to a nominal output stated in the technical sheet, i.e. the burning of a
given amount of allowed fuel per 1 hour. Long-term excessive output could damage the fireplace stove.

Never use flammable fluids, coke, coal or any of the following types of waste as fuel: chipboards,
plastics, plastic bags, soaked wood or wood-shavings, saw-dust or pellets!
!!!Burning of the abovementioned material not only highly pollutes our environment but also damages
the fireplace insert and the chimney!!!
5.2 Starting the fireplace insert for the first time
Before the first use all remaining stickers must be removed, all accessories must be taken out of the ashpan or
fireplace and the same applies for the transport safety pins. All plastic cover plugs on threaded connections
are not functional, they are only used for transport. Check that bulk shutters for directing the draft, chamotte
tiles and the barrier are set correctly (as they might have slipped from their correct positions during transport or
installation). Repair any defects you might find in setting, otherwise the proper functioning of the heater is
endangered. After setting the fireplace insert, connecting it to the chimney and, if need be, connecting the
exchanger to the warm-water set and filling it with a heat-carrying medium, start heating slowly and continue
for at least two hour. Leave the stoves and ashpan doors open (approx 10-20mm) before and during the first
heating in order to prevent the sealing material to mix with the paint. The fireplace insert surface is covered with
heat-resistant paint. During the first heating, after becoming temporarily soft, the paint will eventually become
hardened. During the soft phase the paint surface is more vulnerable to being damaged by a hand or other object.
small
amount of fuel with a lower temperature. The entire process of first putting the product into operation is
done with the maximum opening of the air supply. Therefore, the first two loadings of fuel should
correspond to the bottom limit of the recommended fuel batch ( ). All
materials must get used to the heat load. You will prevent cracks in chamotte bricks, damage of the paint or
deformation of the insert materials by a careful first heating. Following loadings of fuel should then
correspond to the maximum allowed fuel batch (
hours. Thanks to these high temperatures (maximum performance), the paint is reinforced. Hardening of
the paint on the fireplace insert might be accompanied by a temporary smell, which will disappear after a while.
Make sure the room is properly aired when burning the paint. Furthermore, ensure that no small
animals or birds are present in the room containing paint exhausts. We also recommend turning off
aquariums air intakes during the first heating.
In general, the heating up and cooling of the fireplace insert is accompanied by a specific sound; this is
intended.
After the fireplace insert and eventually the exchanger cools down, it is possible to begin assembling
the outer coating of the insert.
5.3 Kindling and firing
1. Fireplace inserts with grate - first put crumpled paper into the chamber and then lay chopped wood on it.
You can also used the solid fire-starter to start the fire. After starting fire, let it burn freely with all air regulation
elements open. It is forbidden to use flammable liquid (oil, petroleum, etc.) for starting fire! After the fire
begins to burn and the draft is strong enough, bigger logs might be added without the danger of smoke. Continue
stoking the amount of fuel determined based on the nominal output of the fireplace insert.
2. Fireplace inserts without grate - only secondary air is used for burning; therefore wood logs need to be
stoked first, then chopped wood and finally small cuttings and paper. After starting fire, let it burn freely with all
air regulation elements open. It is forbidden to use flammable liquid (oil, petroleum, etc.) for starting fire!
After the fire begins to burn and the draft is strong enough, bigger logs might be added without the danger of
smoke. Continue stoking the maximum amount of fuel determined based on the nominal output of the fireplace
insert.
Fuel consumption is always stated in the technical sheet. Burning intensity is regulated by air intake controls
or, if a smoke shutter is installed, by limiting the draft in the chimney. Larger amount of fuel or a strong draft
and air take might cause overheating and damage of the fireplace insert. Too weak draft leads to glass
blackening or to a smoke escaping into the room when opening the door and stoking fuel.
Warning: Fireplace doors must always be closed, with the exception of the first heating, stoking fuel and
removing ash. When the fireplace insert is not in operation for a longer period of time, it is necessary to check
that the flue pipes, chimney and combustion chamber are clear.
5.4 Stoking fuel
In order to prevent smoke escaping into the room when stoking fuel, please follow the following procedure:
Approximately 5 or 10 seconds before opening the fireplace doors open the air intake regulators and then only
slightly open the stoking doors, wait for few seconds for the exhaust gas to get sucked into the chimney and only
then fully open the door. When opening the stoking door, a special attention must be paid to the danger of hot
fire-brands falling out. After stocking fuel, close the door again. After the fuel starts burning (with clear fire),
return the regulator back to its original position. The amount of stoked fuel should correspond to an hourly
consumption value for the concrete fireplace insert (see the technical sheet). Overheating can permanently
damage the fireplace insert construction.
Warning: To prevent exhaust gas escaping into the room during stoking add fuel after its burning down on
the glowing base.
5.5 Operation during the transition period
The chimney draft (sucking exhaust gas from the fireplace insert) might be weaker during the transition
period, i.e. when the outside temperature is higher than , during rainy and humid days or during gust airs.
During this period the fireplace insert should be operated with the minimum possible fuel so that the fire, as well
as the chimney draft could be improved by opening the air intakes.
Tip: During this period a so-called atmospheric plug can be created in the chimney mouth due to the draft
conditions. The plug can caused smoke escaping into the room when lighting fuel. We recommend letting a
piece of paper burn down preferably in the upper part of the combustion chamber before lighting the kindling.
This seemingly negligible smoke is enough to break through the atmospheric plug. Afterwards you can freely
light paper (or solid fire-starter) and be sure that even a humid chimney is clear.
In this period it is also possible to use the same lighting method as for the fireplace inserts without grate (with
no ashpan).
5.6 Ash removal
Make sure that the ashpan is cleaned when being half full in order to prevent the ash reaching too close to the
grate and thus damaging it. At the same time the ash would block the intake of air required for burning.
Removing ash from the ashpan should be carried out when the fireplace stove is cold and preferably ready for
the next heating. A vacuum cleaner designed for cleaning ash with a filter for small filth can be also used for
cleaning the cold ashpans or heater without ashpans. Ash from burnt wood can be used for composts or
fertilizing. Store the ash in closed non-flammable containers.
Warning: Make sure that the ash does not contain any glowing remains of wood that could cause fire in the
waste container.

Warning: For some fireplace insert types the ashpan is located in a basin under the grate and cannot be
removed from the side. The ashpan can be removed only when the heater is cold and not in operation. The
ashpan is accessible after lifting the grate.
Be careful when removing hot ash!
6. Cleaning and maintenance
Your fireplace insert is a high-quality product and no significant defects will appear during normal operation.
Fireplace insert and flue system need to be checked and cleaned regularly and thoroughly before and after the
heating season.
For cleaning and maintenance work you always have to make sure that the stove is not warm!
The surface of the fireplace stove is protected by flame-retardant coating. The flame-retardant coating
is not anticorrosive. Avoid direct contact with water, other cleaning agents, abrasives or solvents.
Clean the surfaces of the fireplace stove with a soft, dry cloth!
6.1 Cleaning the glass
The cleanliness of the window is influenced not only by the using of suitable fuel, providing sufficient air
intake and chimney draft but also by the method of operating the fireplace insert. In this respect we recommend
stoking only one layer of fuel and distributing the fuel as evenly as possible and as far from the glass as
possible. If the glass becomes dirty, try increasing the burning intensity by opening the air intake and the glass
will clean itself.
Sooty windows can be cleaned in cold state using newspapers or wet cloth dipped in wood ash. Usually
also liquid cleaning agents are used for cleaning the stove window. But these may in some cases, depending on
the composition of the cleaning agent and its interaction with combustion residues (ash particles, etc.), harm the
gaskets and/or the glass-ceramics and/or the decoration colour of the fireplace viewing panel.
The producer is not responsible for damages, which are caused by attack in using of chemical agents.
6.2 Cleaning the fireplace inserts / disassembly of chamotte
All sediments in flue pipes and combustion space must be removed during cleaning. Repair, ideally by
removing, all fallen-off parts of the chamotte lining. The integrity of the chamotte lining must be monitored also
during the heating season. Spaces between individual chamotte fittings serve as a heat dilatation preventing
cracking of the fittings and must not be filled by filling material as was usual with older types of solid fuel
heaters. Cracked chamotte fittings are still functional until they fall out! Bulk shutter for directing the draft,
if used, should be removed during cleaning (this enables easier access to the space above them). The fireplace
insert cleaning (with the exception of glass) should be done without water cleaner, i.e. using only vacuum
cleaner or steel brushes. Any modifications of the fireplace insert are unacceptable. Use only spare parts
approved by the manufacturer. Disassembly of chamotte (see the Chamotte chamber). From time to time the
friction areas of the door hinge and the closing mechanism should be oiled using carbonic fat or grease designed
for high temperatures. Close the fireplace insert with corresponding slide valves when not in operation.
6.3 Cleaning the chimney
Each user of a solid fuel heater is obliged to ensure regular checkups and cleaning of the chimney in
accordance with the government regulation no. 34/2016 Coll. from 22st January 2016.
7. Disposal of covers and the discarded product
Packaging and the discarded product should be liquidated in accordance with law no. 125/1997 Coll. and
related regulations.
Packaging:
a) wooden parts can be used for heating
b) plastic package is to be placed into a container for sorted waste
c) screws and handles are to be taken to a waste collection station
d) bag with the separator of air humidity is to be placed to separated waste
Discarded product:
a) dismantled glass is to be placed into a container for sorted waste
b) sealing and chamotte boards are to be placed into communal waste
c) metal parts are to be taken to a waste collection station
8. Warranty
Remember to read the attached guarantee certificate before you put your stove in operation. It contains
information about obligations that must be met for possible guarantee claims to be recognized.
The guarantee does not cover damage caused by incorrect operation.

DE Allgemeine Einbau-
der Firma Romotop GmbH
- n der Firma Romotop GmbH
iligen Kamineinsatztyps
Die Montage, der Anschluss und die Inbetriebnahme des darf nur von autorisiertem
Es ist nich
1. Einleitung
2. Technische Beschreibung
3. Sicherheitsvorschriften
3.1
3.1.1 Sicherheitsabstand eines Kamineinsatzes im Raum von brennbaren Werkstoffen
3.1.2 eitungen von brennbaren Werkstoffen und Baukonstruktionen
3.2
3.3
4. Montagevorschriften
4.1 Allgemein
4.2 Anschluss an den Kamin (Schornstein)
4.3 Umbau des Kamineinsatzes
5. Bedienungsanleitung
5.1 Brennstoff
5.2 Erste Inbetriebnahme des Kamineinsatzes
5.3 Einheizung und Heizung
5.4 Brennstoffzulegung
5.5
5.6 Beseitigung der Asche
6. Reinigung und Instandhaltung
6.1 Reinigung der Glasscheibe
6.2
6.3 Reinigung des Kamins
7. Entsorgung der Verpackung und des ausgesondertes Produkts
8. Die Garantie
1. Einleitung
Wir bedanken uns bei Ihnen, dass Sie eben unseren Kamineinsatz beschafft haben und gratulieren Ihnen
s der Firma Romotop GmbH, eines
Heims bzw. Ihres Erholungsobjekts steigert, sondern auch als
staublosem Betrieb und vollkommener, umweltfreundlicher Verbrennung. Alle von unserer Firma hergestellten
240/2002 bzw. 229/2002
er
Einrichtung zu informieren. Bewahren Sie die Anleitung und das technische Datenblatt auf, um zu Beginn jeder
2. Technische Beschreibung
Wochenendh Romotop GmbH werden aus hochwertigen
Werkstoffen hergestellt - Gusseisen, CORTEN-
belasteten Bauteile werden aus HARDOX-Stahl produziert. Die Stahlk
Vollblech-
verbunden sind, um
Glas verhindert zugleich das Herausfallen von Teilen des brennenden Holzes und Austritt von Rauch in den
Raum. Der Feuerraumboden ist in der Regel mit einem herausnehmbaren Eisengussrost versehen. Vor dem Rost
ist in d
ggf. eine Blech-
4 m
einzubauen. -
g. Die
von Rauchgasemissionen in die
Teil bzw. ganz sperren
einer Rauchklappe (manuelle Sperrklappe in der Rauchabfuhr, die den Luftkanal max. zu 75% versperrt)
20 Pa empfehlenswert. Der
die Aschekastenabde
Brennstoffzulegung und Beseitigung fester Verbrennungsreste, um den Rauchgasaustritt in den Raum zu
verhindern.

ebaut werden, was
Warmwasseraufbereitung zus
ZLZ) *, aus Fluren und
ZLZ
leisten somit nicht nur einen Beitrag zur Erhaltung eines angenehmen Klimas in Ihrem Heim, sondern
reduzieren auch die Energiekosten (im Haus wird die be Bei der
Installation des zentralluftzufuhr (ZLZ) an der Wand ist darauf zu achten, dass das Rohr in einem negativen
Winkel -Lei .
Ein Kamineinsatz mit ZLZ
Komforts kann das Heiz mit elektrischer Verbrennungsregelung
versehen werden.
Kamineinsatzes zu verhindern (die Klappe der zentralen Luftzufuhr wird mit einer Steuerungseinheit mit
Rauchgase gesteuert).
Hinweis:
Bet
vorzunehmen ist.
*
aufgrund von Feuchtigkeitskondensation, wenn das Produkt Die Garantie bezieht sich nicht
3. Sicherheitsvorschriften
-1 ed.2/2009 benutzt werden. Bei
-, bzw. Explosionsgefahr entstehen
u setzen. Der Kamineinsatz darf danach erst nach
sicherzustellen, 8bis 15 m3
Problem wird mittels der aus einem getrennten Raum angeschlossenen CPV geregelt. Ebenfalls das Gitter der
Verbrennungs- -
Brennstoffs stets langsam. Sie verhindern somit den Austritt von Rauch und Asche in den Raum. Der
Kamineinsatz erfordert zeitweilige Bedienung und Beaufsichtigung.
beliebige Kunststoffteile, Holzwerkstoffe mit chemischen Bindemitteln (Holzspanwerkstoffe, usw.) und
Gesetz 201/20212 zu verbrennen.
Achten Sie beim Heizen darauf, dass mit dem Kamineinsatz keine Kinder manipulieren. Der
Kamineinsatz darf nur von Erwachsenen bedient werden!
behandschuhten Hand -
solange er warm ist, beliebige bren
- z. B.
Bei saisonbedingter Benutzung und bei schlechten Zug- eren Betriebsunterbrechung
vor allem:
3.1
3.1.1 Sicherheitsabstand eines Kamineinsatzes im Raum von brennbaren Werkstoffen
Beim Einbau des Kamineinsatzes im Raum der Klasse B, C und Dist der
80 cm und in sonstigen Richtungen 40
cm 20 cm einzuhalten. Beim Einbau des Kamineinsatzes
der Klasse E oder F 501-1+A1/2010 und 73
0810/2016 glich, den von der Norm vorgeschriebenen Sicherheitsabstand des
Kamineinsatzes von brennbaren Stoffen einzuhalten, ist eine Schutzblende lt. zu
verwenden.
Einstufung von Baustoffen nach der Brennbarkeitsstufe
A1 oder A2
B
C
D Weichholz
E oder F Ho
3.1.2 Baukonstruktionen
Werkstoffen und von Rohr 20 cm. Von sonstigen
Konstruktionsteilen aus brennbaren Werkstoffen mind. 40 cm . Es

handelt sich um Baustoffe der Klasse B, Cund Dlaut -1+A1/2010 (siehe Tabelle Nr. 1). Das
unbrennbar
vorzubeugen.
3.2
Ist der Kamin nicht auf 100%
stellen, z. B. Blech (Dicke mind. 2 mm), Keramik, Hartglas, Stein, so dass die Temperatur des brennbaren
4 beim Betrieb nicht
-80 cm in senkrechter Richtung zur Kami
-40 cm
brennbaren Stoffen gestellt/gelegt werden.
3.3 (Schornstein):
Regierungsverordnung Nr. 34/2016 Slg. vom 22.1.2016
Kamin.
-
-
-
Ansammlung von Raum im Haus nicht zur Folge haben,
- die lokale Feuerwehr informieren, um zu beurteilen, ob das Ereignis der Feuerwehrbereitschaft zu melden
ist,
- bis zum Ausbrennen des Kamins das Haus nicht verlassen, die Kamintemperatur und den
Verbrennungsverlauf
- nach dem Ausbrennen vor erneutem Einheizen mit dem Kaminfegerdienst Kontakt aufnehmen und den
Kaminzustand beurteilen lassen, mit dem Kaminofenhersteller Kontakt aufnehmen und den Kamineinsatz
untersuchen lassen.
4. Montagevorschriften
Vorschriften, die nationale Normen und EU-
allem:
- Kamine mit offener und gesc
-
-
- e -
Brennstoffverbrauchern
- Kamine - Allgemeine Anforderungen
-1+A1/2010 - Brandschutzklassifikation von Bauprodukten und Baukonstruktionen
Brandsicherheitseinrichtungen
Dekret Nr. 268 / 2011 Slg. -
4.1 Allgemein
ung einer
Kamineinsatzes, des Rauchabzugs und des Kamins (Schornsteins), falls dieser nicht von einer anderen Stelle, z.
B. vom Dach bzw. mit Hilfe einer zu
4.2 Anschluss an den Kamin (Schornstein)
Vor der Montage eines geschlossenen Kamineinsatzes ist anhand einer Berechnung nachzuweisen, dass die
einzubauenden Kamineinsatzes entspricht.
- Sie sich daher vor der Anordnung Ihres
Kamineinsatzes einen Rat bei Ihrem Kaminfeger. Die erforderlichen Kaminwerte sind dem anliegenden
technischen Datenblatt zu entnehmen. Bei zu starkem Kaminzug ist es angebracht, eine geeignete Kaminklappe
bzw. einen
des Kamineinsatzes zur Folge haben.
Die niedrigste 5 m (gemessen
Anschluss an den Rauchgaskanal ist mit dem Rauchgaskanalhersteller abzustimmen. Der Rauchgaskanal ist
mindestens 5 cm 1/4
darstellt (d. h. 1,5 m)
brennbaren Baustoffen, sind
die Dichtigkeit und aufweisen. Der Querschnitt der Rauchabzugska
anhand einer Berechnung nachgewiesen, dass der Querschnitt des Rauchabzugkanals und des Kamins kleiner
sein kann, als der Querschnitt des Rauchabzugstutzens des Kamineinsatzes, ist der Querschnitt des Rauchabzugs
unmittelbar hinter dem Rauchabzugsstutzen des Kamineinsatzes mit Hilfe eines kurzen Anlaufs bzw. eines
Sprungs zu reduzieren. Ein flexibler Rauchabzug aus dem Werksto A.1. darf nur an Stellen
7.2.1 der
7.2.5 sicherzustellen. Ein senkrechter Rauchabzug darf nur in den in 8.3.4 und
8.3.5
Ein Kamineinsatz kann an einen gemeinsamen Luftkanal mit einem Gasverbraucher bei mehrschichtigen
Kangeschlossen werden.

Das Austreten von Wasser in das Produkt bei Verwendung eines vertikalen Rauchkanal mit
erde!
Es
4.3 Umbau des Kamineinsatzes
Kamin wird in der Norm .Die Montage, der Anschluss und die Inbetriebnahme des
darf nur von autorisierte
Bei der Installation und Installation eines Kamineinsatzes folgende Richtlinien beachten:
1. - und Montagevorschriften einzuhalten.
2. Nach dem Einbau des ganzen Kamins darf weder der Eintritt noch Austritt der Konvektionsluft durch
- sowie Austrittsquerschnitt der Konvektionsluft sind
3.
den von der Firma Romotop s.r.o. hergestellten keramischen Verkleidungen angepasst.
4.
5. Der Austritt der erhitzten Konvektionsluft ist mind. 30 cm unter der Decke anzuordnen (Abb. 2).
6.
Temperatur darf den Wert
7.
-Folie zu kleben.
8. In der Wand, an der sich der Kamin befindet, darf sich keine Strom-, Wasser- und Gasleitung befinden.
Weder in der Wand noch auf deren O
9. und Breite des Kamineinsatzes einzuhalten, dass die Konvektionsluft frei
10. 40 cm
entfernt sein, b
Temperatur bis erreichen!
11. Vergessen Sie nicht, dass sich von 80 cm vor der
40 cm der
12. Vergessen Sie nicht - eit hergestellt sein muss und dass um den Sims
ebenfalls Konvektionsluft durch einen Zwischenraum von mind. 1 cm
13. Bei der 4 m lange
14. Die Rohre der Warmluftvert
- n
brennbaren Materialen.
15.
16. Bei dem Ka
der Kamineinsatz in irgendeiner Art angepasst werden!!!
nationale Normen und EU-Normen betreffen, vor allem: Lassen Sie sich vor dem Einbau ein Fachprojekt
anfertigen.
1:10 bzw. 1:20 erstellt werden. Vor der Inbetriebnahme des
Kamineinsatzes ist eine Kontrolle vom Kaminfeger durchzu
Kapitel 9 . Die Kontrolle des Kaminanschlusses mit dem Rauchkanal an
Das Ergebnis der Inspektion ist im Abg
technischen Berichts nach dem Dekret Nr. 34/2016 Slg.
Vertikaler Schnitt eines Einmantel-
Abb. 2

01 - Kaminluftkanal 11 - Luftzufuhr aus einem anderen Raum (bzw. CPV)
02 - 12 -
03 - 13 -
04 - Decke der Warmluftkammer 14 -
05 - 15 - Wand der Warmluftkammer
06 - 16 - Kaminsims
07 - Raum der Warmluftkammer 17 - Kaminsimsschutz
08 - Rauchabzug des Kamineinsatzes 18 - Luftzufuhr in die Warmluftkammer
09 - Rauchkammer des Kamineinsatzes 19 - Luftzufuhr vom Bereich unter dem Kamineinsatz
10 - 20 -
21 - CPV-Stutzen
Das Schema der Kaminzusammenbauanordnung gilt allgemein -
- sowie Warmwassertauscher.
5. Bedienungsanleitung
5.1 Brennstoff
darf nur Holz Nr. 201/2012 Slg. verbrannt werden.
Zum Erreichen der Nennwerte des Kaminofens ist es empfehlenswert, trockene Holzscheite mit dem
Durchmesser 5-8 cm 20-30 cm und mit niedrigerer Feuchtigkeit, als 20% (optimal sind 10%).
Reisig und klein gespaltenes Holz ist lediglich beim Anheizen zu verwenden. Um das Holz richtig zu trocknen,
Verbrennung der gegebenen Menge des erlaubten Brennholzes in 1 Stunde.
Pellets benutzt werden!
auch den Kamineinsatz und den Kamin (Schornstein)!!!
5.2 Erste Inbetriebnahme des Kamineinsatzes
Alle Kunststoff-Abdeckstopfen
an den Gewindeverbindun
Sie nach der Abbildung aus dem technischen Datenblatt, ob die lose gelagerten Zugumlenkungsblenden,
ichkeit, dass sie beim Transport
bzw. bei der Installation in die falsche Position gerutscht sind). Falls Sie deren fehlerhafte Anordnung
feststellen, bringen Sie die Bauteile in die richtige Position, andernfalls ist die richtige Funktion der
Heizvorricht
heizen Sie ein und heizen sie mindestens zwei Stunde "mit kleiner Flamme". Lassen Sie vor sowie im Laufe des
ca. 1-2 cm), damit das
feuerfeste Farbe
einem Gegenstand. Beim ersten Einheizen ist der Kamineinsatz mit kleiner Flamme, mit einer kleineren
Brennstoffmenge und bei niedriger Temperatur zu beheizen. Der ganze Prozess der Inbetriebnahme des
Produkts bei voll Luftzufuhr. Erste zwei Nachlegen sollten der Mindestgrenze des
es Lacks und Deformation von Materialen der Einsatzkonstruktion.
5 6 Nachlegen sollten Maximalmenge des Brennstoffs (siehe
. Das Ausbrennen des
hrleisten, ggf.
empfehlenswert, die Luftversorgung von Aquarien auszuschalten.
delt sich um keinen
Mangel.
Kamineinsatzes eingebaut werden.
5.3 Einheizung und Heizung
1. Bei einem Kamineinsatz mit Rost - geben Sie in den Feuerraum zuerst zerknittertes Papier und schichten
dem Einheizen das Feuer bei offenen Luftregulierungselementen frei aufbrennen. Es ist verboten, zum
Sobald das Feuer aufbrennt und
austritt. Legen Sie stets die festgelegte Brennstoffmenge nach der Nennleistung des Kamineinsatzes zu.
2. Bei einem Kamineinsatz ohne Rost -
Papier. Lassen Sie nach dem Einheizen das Feuer bei offenen Luftregulierungselementen frei aufbrennen. Es ist
Sobald das Feuer
scheite zugelegt werden, ohne dass der Rauch
in den Raum austritt. Legen Sie stets die festgelegte Brennstoffmenge nach der Nennleistung des
Kamineinsatzes zu.
Verb
ng des Kamineinsatzes zur Folge haben. Zu kleiner Zug
beim Zulegen in den Kamineinsatz.
Hinweis: nahme der Inbetriebnahme,
Feuerraums zu kontrollieren.
5.4 Brennstoffzulegung
Zur Verhinderung des Austritts von Rauchgas in den Raum beim Zulegen empfehlen wir: Etwa 5 bis 10
nden warten, solange das Rauchgas nicht in den Kamin abgezogen wird und erst danach die

zugelegten Brennstoffs soll dem informativen Stundenverbrauch des jeweiligen Kamineinsatzes entsprechen
werden.
Hinweis: ende Asche verhindert werden.
5.5
, an regnerischen und
es Rauchgases
aus dem Kamineinsatzes) verschlechtern. Es ist empfehlenswert, den Kamineinsatz in diesem Zeitraum mit der
auch den Kaminzug verbessern z
Tipp:
verursachen. Es ist daher empfehlenswert, v - am besten
en )
(ohne Aschekasten) benutzt werden.
5.6 Beseitigung der Asche
Achten Se
nungsluft behindern. Der Aschekasten ist am
Reinigung des Aschekastens in kaltem Zustand ist ebenfalls ein Aschesauger mit Kleinpartikelfilter geeignet.
Hinweis:
die Feuer im Abfallbe
Hinweis: Bei bestimmten Kamineinsatztypen befindet sich der Aschekasten im Raum unter dem Rost, ohne
herauszunehmen. Der Zugang zum Aschekasten ist nach dem Abklappen des Rosts frei.
6. Reinigung und Instandhaltung
hen
Es ist notwendig den Kamineinsatz
Hei
der Kamineinsatz vor!
Die Kamineinsatzes obe Vermeiden Sie direkten Kontakt
Die Obe Kamineinsatzes reinigen Sie mit einem weichen, trockenen Tuch!
6.1 Reinigung der Glasscheibe
ausreichenden Verbrennungsluftzufuhr und des entsprechenden Kaminzugs auch die Art, wie der Kamineinsatz
bedient wird, Einfluss. Wir empfehlen in diesem Zusammenhang nur eine Brennstoffschicht zuzulegen, so dass
ng des
mit Holzasche.
die Glaskeramik und/oder die Dekorationsfarbe der Kaminsichtscheibe angreifen.
chemischen Stoffen entstehen.
6.2
Herausgefallene Teile der Schamottausmauerung sind zu reparieren, am besten auszutau
ganz herausfallen! Wir empfehlen, bei der Kamineinsatzreinigung die losen Zugumlenkungsblenden
herauszunehmen, falls sie bei dem Kamineinsatz vorhanden sind (zur Erleichterung des Zugangs zu dem Raum
vorgenommen, z. B. mit Hilf
6.3 Reinigung des Kamins
Je Slg. vom 22.1.2016 sicherzustellen.
7. Entsorgung der Verpackung und des ausgesondertes Produkts
Wir empfehlen im
Art der Entsorgung der Verpackung und des unbrauchbaren, ausgesonderten Produkts.
Verpackung
a) Holzteile der Verpackung zum Heizen benutzen

b) die Kunststoffverp
c) Schrauben und Halter beim Altstoffhandel abliefern
Ausgesondertes Produkt:
a) das Glas ausbauen und in einen Container mit getrenntem Abfall geben
c) Metallteile beim Altstoffhandel abliefern
8. Garantie
Wichtig ist, dass Sie vor Inbetriebnahme des Kaminofens den beiliegenden Garantieschein durchlesen.
n
anerkannt werden.

FR S.A.R.L.
- entreprise Romotop
S.A.R.L..
La fiche technique
1. Introduction
2. Description technique
3.
3.1
3.1.1
3.1.2 construction
3.2 Protection du plancher
3.3
4.
4.1 ales
4.2
4.3
5.
5.1 Combustible
5.2
5.3 Allumage et chauffage
5.4 Chargement de combustible
5.5
5.6 endres
6. Nettoyage et entretien
6.1 Nettoyage de la vitre
6.2
6.3
7.
8. Garantie
1. Introduction
Nous vous remercions d
S.A.R.L.
rendement thermique
240/2002 ou 229/2002.
Dans votr
correctes de ce dispositif. Veuillez conserver l
Nous ne fournissons une garantie pour nos produits
2. Description technique
i
S.A.R.L. - fonte, acier CORTEN et aciers de
ombe ou
4 m, on conseille
thermique du dispositif chauffa -dessus du
umage,
75 %).
20Pa. La vanne