Ronix RP-0101C User manual

HIGH PRESSURE WASHER
INDUCTION MOTOR
RP-0101C

USER MANUAL 3
SPECITICATIONS
model RP-0101C
motor induction
power 1000W
voltage 220-240V
frequency 50-60HZ
protection class I
degree of protection IPX5
max pressure 100bar
max flow 5.2L/min
rated tempreture 0-40 °C
max inlet pressure 7 BAR
sound pressure level 67±3dB(A)
sound power level 80dB(A)
vibration value: 3.3m/s2
weight 6.03KG
accessories
Gun/Adjustable nozzle/5m PVC
hose/cleaning pin/ 1/2 quick
connector/ 2m self_suction hose
PARTS LIST switch handle
water inlet
pump
water outlet
stand
motor

HIGH PRESSURE WASHER
INDUCTION MOTOR
4
PRODUCT DESCRIPTION
.PURFPOSE
- The high pressure cleaner is designed to clean vehicle, machines,
buildings, facades, etc. in the private sector.
.AREAS OF APPLICATION
- Never use the machine in potentially explosive areas under any
cirummstances!
- The operating temperature must be between 0 and +40˚C
- The machine consists of an assembly with a pump, which is encased
in a shock absorbing housing. For an optimal working position the
machine come with a lance and a non-slip handle grip, whose shape
and configuration comply with the applicable regulations.
- Do not cover or modify the lance or the spray nozzles in any way.
- The high pressure cleaner is designed to be used with cold or lukewarm
(The ideal storage temperature is between 10 °C and 30 °C but water
temperature should be between 0-40˚c); higher temperatures can
damage the pump.
- Do not use water that is dirty, gritty or contains any chemical products,
as these could impair operation and shorten the life of the machine.
- Accessories can be used to carry out work with foam cleaners, sand spraying.
IMPORTANT:
This machine is not suitable for connection to the potable water mains.
IMPORTANT SAFETY INSTRUCTIONS
WARNING!
This appliance is not intended to use by children or other persons without
assistance or supervision if their physical, sensory or mental capabilities
prevent them from using it safely.
Children should be supervised to ensure that they do not play with the appliance.
Before starting up your machine please check it carefully for any defects.

USER MANUAL 5
If you find any, do not start up your machine and contact your distributor.
.ESPECIALLY CHECK
The insulation of the power cord should be faultless and with out any cracks.
If the power cord is damaged, an authorized distributor should replace it.
WARNING!
- Do not use this appliance without reading this instruction sheets.
- The electric supply connection shall be made by a qualified electrician
and comply with IEC60364-1.
- The electric supply to this appliance should include either a residual
current device that with interrupt the supply if the leakage current to earth
exceeds 30Ma for 30ms or device that will interrupt the earth circuit.
WARNING!
This appliance has been designed for use with the cleaning agent supplied
or recommended by the manufacturer. The use of other cleaning agents
or chemical may adversely affect the safely of the appliance.
WARNING!
Do not use the appliance within range of person unless they wear
protective clothing.
WARNING!
- High pressure jets can be dangerous if subject to misuse. The jet mast
not be directed at persons, live electrical equipment or the appliance itself.
- Do not direct the jet against yourself or others in order to clean clothes
or foot-wear,
- Risk of explosion – do not spray flammable liquids.
- Disconnect from the electrical power supply before carrying out user
maintenance.
- High pressure cleaners shall not be used by children or untrained personnel.
- To ensure appliance safety, use only original spare parts from the

HIGH PRESSURE WASHER
INDUCTION MOTOR
6
manufacturer or approved by the manufacturer.
WARNING!
Water that has flown through backflow preventers is considered to be
non-potable.
WARNING!
The machine shall be disconnected from its power source during
cleaning or maintenance and when replacing parts for mains operated
machines by removing the plug from the socket-outlet.
WARNING!
High pressure hoses, fittings and couplings are important for safety of
the appliance. Use only hoses, fitting and couplings recommended by
the manufacturer.
- Do not use the appliance if a supply cord or important parts of the
appliance are damaged, e.g. Safety devices, high pressure hoses,
trigger gun.
WARNING!
If an extension cord is used, the plug and socket must be of watertight
construction.
WARNING!
Inadequate extension cords can be dangerous.
- This high pressure washer must not be used at temperatures below 0˚C.
WARNING!
- Cord on drums should always be completely un winded to prevent the
cord from overheating.
- If an extension cord is used, the plug and socket must be of watertight
construction.
- Inadequate extension cords and be dangerous.

USER MANUAL 7
- Comply with the below-mentioned requirements for length and cored
dimensions.
1.0mm max.12.5m
1.5mm max.20m
2.5mm max.30m
- Power cord connections should be kept dry and off the ground.
- If the power cord is damaged, it must be replaced by the manufacturer
or his service agent or similarly qualified person in order to avoid a
hazard.
- All keep the machine on a stable and flat surface during operation,
handling, transportation and storage. Sudden overturn of machine will
cause injury to body.
- In the event of accident or breakdown, switch off the machine
immediately. (e.g. contact with detergent: rinse with an abundance of
clean water.
ATTENTION:
Through poor conditions of the electrical MAINS, shortly voltage
drops can appear when starting the EQUIPMENT. This can influence
other equipment (e.g. Blinking of a lamp). If the MAINS-IMPEDANCE
Zmax<0.335 OMH, such disturbances are not expected. (in case of
need, you may contact your local supply authority for further information.)
WARNING!
ELECTRICAL SHOCK HAZARD
Improper connection of the equipment – grounding conductor can result
in a risk of electrical shock. Check with a qualified electrician or service
person if you are unsure if an outlet is properly grounded. DO NOT
modify the plug provided with the appliance to fit an outlet, have a proper
outlet installed by a qualified electrician.
.MAINS POWER CONNECTION
The following should be observed when connecting the high pressure

HIGH PRESSURE WASHER
INDUCTION MOTOR
8
washer to the electric installation:
- The electric installation shall be made by a certified electrician and
comply with IEC 60364.
It is recommended that the electric supply to this appliance should
include either a residual current device that will interrupt the supply if
the leakage current to earth exceeds 30 mA for 30 ms.
IMPORTANT:
Only use water without any impurities. If there is a risk of running sands
in the inlet water (i.e. from your own well), an additional filter should be
mounted.
- Safety devices
- The unloader valve can reduce pressure if it exceeds preset values.
The spray gun features a looking device. When the pawl is activated,
the spray gun cannot be operated.
- Thermal sensor
A thermal sensor protects the motor against overloading. Machine will
restart after a few minutes when the thermal sensor has cooled.
ASSEMBLY
- Position the washer as NEAR as possible to the water supply.
- The washer must be used standing on a secure, stable, positioned as shown.
1. Installing the spray wand Fit the spray wand into the gun and rotate
it until the two parts are completely locked
2. Connect the high pressure hose to the trigger gun. Connect the sliver
end of the high-pressure hose to the trigger gun and twist the nut as
indicated to secure the connection.

USER MANUAL 9
3. Connect the high-pressure hose to the water outlet
Connect the other end of the high-pressure hose to the water outlet
on the washer and twist the black rotatable end-piece as indicated to
secure the connection.
4. Connect the garden hose to the water inlet
Connect the garden hose adaptor(female coupler) to the water inlet of
the pressure washer, then thread your garden hose(male end) into the
garden hose adaptor.
NOTE:
The machine not suitable for connection to the potable water main.
WARNING!
The intake water temperature must not exceed 40. The water supply
must not exceed 7 Bar .

HIGH PRESSURE WASHER
INDUCTION MOTOR
10
CAUTION:
The washer must only be used with clean water; use of unfiltered water
of corrosive chemicals will damage the washer.
- Push the motor switch to “OFF” position.
Check the electrical supply voltage and frequency (Volt/Hz) correspond
to those specified on the washer rating plate. If the power supply is
correct, you may now plug in the washer.
OPERATION
- Turn on the water supply tap fully.
- Release the safety lock then press the trigger for a few seconds to
allow air to escape and discharge residual pressure in the hose.
- Keeping the trigger pressed push the switch to start the motor.
- when restarting the motor, always keep the trigger pressed.
NOTE:
THE MOTOR ONLY RUNS WHEN THE TRIGGER IS OPERATED
CORRECT USE OF STANDARD ACCESSORIES

USER MANUAL 11
- The washer is equipped with adjustable nozzle.
- Jet adjustment from pencil to fan.
WARNING!
Do not adjust the nozzle while the triggter is squeezed.
RECOMMENDED CLEANING PROCDURE
- Dissolve dirt by applying detergent with the fan jet to the dry surface. On
vertical surfaces. Work from the bottom upwards. Leave the detergent
to act for 1 to 2 minutes, but do not allow to dry out. Apply the high from
the surface, working from the bottom upwards.
- Avoid allowing the rinsing water to run on the unwanted surfaces.
STORAGE
- Switch off the washer.
- Turn off the water supply tap.
- After use, the detergent residuals should be removed from the tank.
- Discharge residual pressure by pressing the trigger until no more water
comes out of the lance nozzle.
- Engage the gun safety lock.
- Remove the plug from the socket.
- Operate the washer with non-corrosive/non-toxic antifreeze before
storing for the winter.

HIGH PRESSURE WASHER
INDUCTION MOTOR
12
WARNING!
BEFORE REUSING, COMPLETELY FLUSH THE UNIT OUT WISH
PLAIN WATER. ANTI-FREEZE CAN DAMAGE PAINTWORK SO YOU
MUST ENSURE THERE IS NO ANTI-FREEZE LEFT IN THE SYSTEM
BEFORE USING IT AGAIN.
MAINTENANCE
CAUTION:
Before working on the washer, disconnect the lug from the power supply
socket.
- to ensure good performance. Check and clean the suction and
detergent filters after every 50 hours of operation.
- clean the nozzle with tool provided. Remove the lance from the gun,
remove any dirt from the nozzle hole and rinse.
TROUBLESHOOTING
Disconnect from the electrical power supply before carrying out user
maintenance of checking is correct functioning. To avoid unnecessary

USER MANUAL 13
disappointments, you should check the following before contacting the
service organization.
In case problems other than the above occur, please contact your local distributor.
Recommended ActionCauseSymptom
- Plug in machine
- Try another socket
- Replace fuse
- Switch off other machine
- Try without the extension cord
- Machine not
plugged in
- Defective socket
- Fuse has blown
- Defective
extension cord
Machine refuses to
start
- check that hoses and connections are
airtight
- Clean and replace or refer to local
distributor
- Clean and replace or refer to local
distributor
- Pump sucking air
- Valve is dirty, worn
out or stuck
- Pump seals worn
out
Fluctuating pressure
- Replace fuse
- Switch off other machines
- Check that the main voltage
corresponds to specification on the
model tag
- leave the washer for 5 minutes to cool
down
- Clean the nozzle
- Fuse has blown
- Incorrect mains
voltage
- Thermal sensor
activated
- Nozzle partially
blocked
Machine stops
- change to an installation higher than the
amp consumption of the machine
- You may try without the extension cord
Fuse too smallFuse blows
Allow machine to run with open trigger
until regular working pressure resumes
- Check the water cupply corresponds to
specifications required
- Avoid using long, thin hoses (min. 1/2:”)
- Clean the nozzle
- Clean the filter
- Straighten out hose
- Air in inlet hose
Inadequate supply
of mains water
- Nozzle partially
blocked water filter
blocked
- Hose kinked
Machine pulsating
Contact your nearest Service
Pump/spray gun is
leaking Centre
Machine often starts
and stops by itself
- Wait fir Pump/hoses or accessory to
thaw
- Connect inlet water
- Clean the filter
- Clean the nozzle
- Pumpt/hoses or
accessory frozen
- No water supply
- Water filter
blocked
- Nozzle blocked
Machine starts, but
No water comes out