Roper Rhodes DC14025 User manual

DC14025 - UNIVERSAL
WASHSTAND
Chrome Universal Washstand
FITTING INSTRUCTIONS
Please make sure your basin’s width and depth does not exceed 1000 X 500mm.
Maximum height of legs are 860mm.
Please make sure the warnings and after-care instructions are made available for
the end user to read.
Position the basin such that the main surface is 860mm from the floor.
Ensure the basin is firmly secured to the wall using appropriate basin fixings before
proceeding with the installation of the Washstand,
fix the basin in accordance with the manufacturers instructions.
COMPONENT LIST
x8 Screws
M4 x 26mm
x8 Wall / Floor Plugs
M5 x 27mm
FITTING GUIDE
x2 Legs
x2 Side Bars
x2 Wall Fixing Brackets
x2 Wall Fixing Bracket
Covers
x2 Floor Fixing Brackets
x2 Floor Fixing Bracket
Covers
x1 Front Bar
ADJUSTING YOUR WASHSTAND PRIOR TO FIXING
860mm Max
860mm Recommended
500mm Max
1000mm Max
x 1 Hex Key 2mm
1 2
Xmm
Measure Distance Xmm
CUTTING THE LEGS
Only follow this section if you want to lower the height of the legs.
3
Xmm
Cut distance X from the base of the leg.
Cut the same distance on both legs.
Base Of Leg
CUTTING THE SIDE BARS
1
Only follow this section if you want to shorten the depth of the Side Bars.
Loosely assemble one Side Bar onto a
leg joint. 2
Ymm
Measure from the position you
want your leg to be located, to the
centre of the current leg position.
Ymm
3
CUTTING THE FRONT BAR
Only follow this section if you want to shorten the width of the front bar.
1
Zmm
900mm Loosely assemble the front bar
into the leg joints.
Align the washstand centrally.
Measure a suitable width for your
washstand (Zmm).
Measure the distance between
leg centres this should be 900mm
+/- 5mm
Subtract Zmm from 900mm
900mm -Zmm = Measurement Σ
Please read completely before starting.
The Legs, Side Bars and Front Bar can all be cut down to suit the basin you are installing.
Use a metal pipe cutter with an adjustable cutting diameter. To accommodate Ø28 +
Ø26mm tube.
Slide the knuckle joint onto the leg
and fix the grub screws using the
provided hex key to secure it.
Loosely locate the floor
fixing brackets and covers
onto the legs.
The leg has an adjustable
component that makes contact
with the underside of the basin.
This can be extended up 26mm if
necessary.
x2 Knuckle Joints - with
pre assembled Grub
Screws
Remove the side bar from the joint and cut distance Y on both bars.
IMPORTANT - Do not cut the end with the flange. Only cut the plain end.

AFTERCARE INSTRUCTIONS
• The fittings pack contains small items which should be kept away from young
children.
• The washstand can be dangerous if incorrectly installed. Assembly should be carried
out by a competent person. No liability will be accepted for damage or injury caused
by incorrect product installation or assembly.
WARNINGS
BLEACH
CLEANER
CREAM
CLEANER
Clean surfaces with a soft
damp cloth and mild
soap solution
Do not scrub or scour
Do not use abrasive
cleaning agents.
Do not stand or climb on
the washstand
Do not use abrasive cleaning agents.
For Technical Help Call:
01225 787 870
Brassmill Lane Trading Estate | Bath | BA1 3JF ref: RH 0719 V1
1 2
Σ
mm
3Remove the front bar from the leg joints
and cut Measurement Σon one side.
FIXING AND SECURING YOUR WASHSTAND
The washstand should now fit under
your basin to your desired
dimensions.
Slide the side bars into the leg
joints and fix the grub screws with
the Hex key provided.
3
4Adjust the height of the front bar and
side bars by sliding the leg joint up and
down until you have the desired height.
5
6
Once you have your
desired height, level both
joints using a Spirit level.
Fix the joint to the leg
securely using the pre
assembled grub screws
and the Hex key.
Slide the front bar into the remaining leg joints.
Secure with Hex key provided.
Make sure your floor fixing brackets and
covers are located on the bottom of the legs.
Align the washstand centrally with the basin
and adjust the extension as required.
7
The Washstand should now fit
your basin and be secured to the
wall and floor.
Slide the wall fixing brackets and
the wall fixing bracket covers
onto the side bars to cover the flanged
edge.
Once the washstand is aligned and level, mark out and drill the pilot holes using
a suitable drill bit. Insert the wall / floor plugs.
Using the screws provided fix the washstand to the wall and the floor.
Place the fixing bracket covers over the fixing brackets.
• The washstand is not suitable for hanging heavy items on.
IMPORTANT
Wear suitable eye protection
when drilling. Take care when
using power tools near water.
The use of a residual current
device (RCD) is advised.
Beware of hidden cables or
pipes. Take care if drilling on
tiled surfaces in case the drill
slips. Use masking tape to help
prevent drill from moving out of
alignment.