Roper Rhodes Beat MLE420 Parts list manual

Beat Mirror Installation & aftercare instructions
Please retain for future reference
22
2
OUTSIDE
ZONES
2
ZONE
1
0.75m
2.25m
3.0m
0.6m
0.6m
0.75m
Bathroom Zones Diagram
Distances from a bath tub or shower tray
TB.RR.MLE420 | 09.15 V3 .00
Roper Rhodes, Brassmill Lane Trading Estate, Bath, BA1 3JF
TEL: [phone] | FAX: [phone]
www.roperrhodes.co.uk
Product code
MLE420
ELECTRICAL SAFETY INSTRUCTIONS
(Applicable to UK Installations only)
All ttings must be installed by a competent person, in
accordance with current IEE wiring regulations. If in doubt
consult a qualied electrician
IMPORTANT
Always switch o the electrical supply at the mains during
installation and maintenance. It is recommended that the
fuse is withdrawn or the circuit breaker is switched o for the
necessary circuit before installation commences.
Fitting in Bathrooms is subject to the appropriate zone in
accordance with IEE Regulations. This product is suitable for
zone 2 and outside zones. IT IS NOT suitable for installation in
Zone 0 or Zone 1. It is also not suitable for installation in
saunas, steam rooms or shower cubicles. This product is only
suitable for permanent installation. DO NOT connect to a
trailing plug and socket outlet. Although this product has an
Ingress Protection rating of IP44 it is only suitable for indoor
use. Do not attach the product to surfaces that are damp or
otherwise electrically conductive.
INSTALLATION CARE & SAFETY
Wear suitable eye protection when drilling. Take care when
using power tools near water - the use of a residual current
device (RCD) is advised. Beware of hidden cables or pipes.
Take care if drilling on tiled surfaces in case the drill slips. A
piece of masking tape applied to the wall before marking out
the xing holes will stop the drill from wandering.
IMPORTANT
DO NOT strike glass components with
hard or pointed items. DO NOT place
very hot or very cold items against or in
close proximity to glass surfaces unless
an adequately thick insulation material
is used to prevent such items coming in
contact with the glass.
The nominal thickness of the mirror
glass used in this product is 5mm and is
lm backed for safety. If the glass
becomes chipped or broken replace
immediately.
This product should be positioned well
away from curtains and other fabrics.
Never cover the mirror. This product is
heated, we recommend that it is turned
o after use and should never be left on
for prolonged periods of time
This product could be dangerous and is
only to be installed by a competent
person.
“There is no sound from my Beat Mirror.”
- The volume on either device is muted or turned down.
- There is a problem with the Bluetooth
®
connection - try erasing the connection on the audio device
and then re-pairing.
- There may be interference from other nearby Bluetooth
®
enabled devices - try turning them o.
- The connected devices are too far apart and out of range - try moving the devices closer together.
“I cannot pair the mirror with my Bluetooth
®
device.”
- The mirror may not be in pairing mode - to do this press the button. There will be a short lag
with no visible activity while the device powers on. The indicator light will ash and the mirror will beep
to conrm pairing mode.
- The Bluetooth
®
capability of your chosen device is turned o or out of range.
- There was a problem during pairing - some devices will pair automatically when selected some will
require a pass code or acceptance of the connection before they will nalise the pairing.
- Refer to your Bluetooth
®
device’s instruction manual to ensure it supports the A2DP (stereo Bluetooth
®
)
prole.
- If attempting to connect to a PC or Mac computer, ensure that your Beat Mirror is set as the audio
output device within the audio settings menu of the device. You may need to play a track to nalise the
connection.
“The sound quality is poor.”
- Your Bluetooth
®
device may be close to being out of range and should be moved closer to the mirror.
- For those devices that support the use of Applications, there may be too many running in the
background which can aect the amount of internal resources available on the device to transmit
audio. Closing any non-essential applications may improve audio quality.
- Similarly, if the selected device has Wi-Fi capabilities, turning this o may improve audio quality.
- There could have been a problem during the initial pairing of devices. Erase the connection using your
Bluetooth
®
device and re-pair.
- For those devices with in-built sound equalisation, adjusting these settings can greatly improve the
sound quality of any audio played through your Beat Mirror.
“My Beat mirror is not automatically reconnecting with my Bluetooth
®
device.”
- The mirror will automatically reconnect with paired devices when both devices Bluetooth
®
capabilities
are turned on. Depending on the manufacturer of the Bluetooth
®
device, the order in which the devices
are turned on to automatically connect may vary. In some cases it will be necessary to turn on
Bluetooth
®
capabilities on the audio device before turning on the mirror.
The Bluetooth
®
word mark and are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by
Roper Rhodes is under license. Other trademarks and trade names are those of their respective owners.
with Bluetooth
®
wireless technology
Troubleshooting
C
M
Y
CM
MY
CY
CMY
K
MLE420 _ RR_Beat Illuminated Mirror Instructions v4.pdf 1 03/09/2015 09:12:21

COMPLIANCE
This product complies with all relevant British and European safety standards:
WIRING
This product is manufactured to class I category and must have an earth connection.
COLOUR CODING:
L - Live = Brown
N - Neutral = Blue
- Earth = Green & Yellow
LIGHTS.
To obtain a replacement LED lamp if faulty or broken contact customer services (see details at
foot of page) quoting product code ML420.
OUTSIDE
ZONES
Installation Procedure
The wall surface must be of suitable strength and construction.
1) Measure the distance between the two xing holes on the back of the mirror frame.
2) Draw a horizontal line on the wall using a spirit level approximately 60mm from the desired
position of the top of the mirror.
Mark the drill positions on the horizontal line using the dimension taken from step 1. Accurately mark
the 2 hole positions with a pencil, drill and t the wall plugs.
NOTE: The wall plugs supplied are only suitable for solid stone / brick walls. For plasterboard walls use
specialist wall plugs.
3) The next step is to make the electrical connection from the mirror to the mains supply. Use the
connection wire found at the rear of the mirror to make the necessary connections in accordance with
the current IEE regulations. A second person will need to hold the mirror in place whilst electrical
connections are made.
4) Insert the wall screws supplied into the wall plugs. Leave approximately 5-10mm of the screw
standing proud of the wall. Mount the mirror onto the screws tted to the wall. Ensure mirror is
securely mounted. before leaving unattended.
Strip wires to a suitable
length. DO NOT connect
to a plug & socket outlet.
THIS PRODUCT IS MANUFACTURED TO CLASS I
CATEGORY AND MUST HAVE AN EARTH CONNECTION.
! IF IN DOUBT CONSULT YOUR ELECTRICIAN !
Colour Coding:
L - Live = Brown
N - Neutral = Blue
- Earth = Green & Yellow
The heated pad is on when the light is on. DO NOT leave on for prolonged periods of time.
CLEANING
It is recommended that the unit is cleaned with a soft, dry, non abrasive cloth when turned o. Never
use cleaning agents or abrasive materials on any type of surface nish. Do not allow moisture to come
into contact with the electrical components.
Operating & Aftercare Instructions
Bluetooth
®
Connection and Controls
LIGHT ON / OFF
PREVIOUS TRACK
VOLUME UP
BLUETOOTH ON / OFF
NEXT TRACK
VOLUME DOWN
Pairing Bluetooth
®
enabled devices:
Pairing occurs when two Bluetooth
®
wireless technology enabled devices communicate with each other
and establish a connection. This information is then stored in the memory of each device meaning that
once initially connected, the two devices will not need to pair again.
Your Beat Mirror can link with up to seven separate devices. When this limit is reached any additional
devices paired will erase previous connections to accomodate the new pairing.
Connecting your Bluetooth
®
enabled device to your Beat Mirror:
1. It is recommended that the Bluetooth
®
connectivity of the device you want to pair with your Beat Mirror
is turned on rst to make connection easier.
2. Press the button to put your Encore Mirror into pairing mode. There will be a short lag with no
visible activity while the device powers on, do not press the button again. The LED indicator light will start
to ash quickly and a beep indicates that pairing mode has been turned on and the mirror is discoverable.
3. On the selected Bluetooth
®
enabled device select ‘Bluetooth Mirror’ from the Bluetooth
®
device list to
connect to the mirror.
Note: Devices running Bluetooth
®
Version 2.0 or earlier may need to enter a pairing code before a
connection is made. This code is a device default of 0000 or 1234. These devices will not need to enter a
pairing code again after the initial set-up. Some devices may also ask for the connection to be accepted,
which will be prompted on the device screen.
4. The mirror will beep twice to signal that a connection has been made between the two Bluetooth
®
enabled devices and the indicator light will ash slowly.
5. Once connected, any music played on the paired device will play through the Beat
Mirror.
Tracks can be changed using the and buttons, paused with and volume can be adjusted
with and
6. The lights and heated demister pad can both be turned on with the button. The Bluetooth
®
functions on the mirror will work regardless of whether the light is turned on.
The Bluetooth
®
connection will automatically cease when the two paired devices are out of range.
To manually turn o the Bluetooth
®
functions on the mirror, press and hold the button for 3
seconds. A long beep will conrm that Bluetooth
®
functions have been turned o.
C
M
Y
CM
MY
CY
CMY
K
MLE420 _ RR_Beat Illuminated Mirror Instructions v4.pdf 2 03/09/2015 09:12:21