Rosemount 3051S Series User manual

Reference Manual
00809-0100-4803, Rev GA
September 2017
Rosemount™3051S MultiVariable™Transmitter

i
Reference Manual
00809-0100-4803, Rev GA
Contents
September 2017
Contents
1Section 1: Introduction
1.1 Using this manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Product recycling/disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2Section 2: Configuration
2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3 Engineering Assistant installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3.1 Engineering Assistant version 6.3 or later . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3.2 Installation and initial setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.4 Flow configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4.1 Rosemount 3051SMV Engineering Assistant 6.3 or later . . . . . . . . . . . . . . 7
2.4.2 Basic navigation overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4.3 Launching Engineering Assistant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.4.4 Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.4.5 Fluid selection for database liquid/gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4.6 Fluid properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4.7 Primary element selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4.8 Save/send. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.4.9 Other fluid configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.5 Basic device configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2.6 Detailed device configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.6.1 Model identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.6.2 Alarm and saturation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.6.3 Variable mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.6.4 LCD display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.6.5 Communication setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.6.6 Materials of construction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.6.7 Flow configuration parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.7 Variable configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.7.1 Flow rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.7.2 Energy rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
2.7.3 Totalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
2.7.4 Differential pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
2.7.5 Static pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
2.7.6 Process temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
2.7.7 Module temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
2.7.8 Analog output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

ii
Reference Manual
00809-0100-4803, Rev GA
Contents
September 2017
Contents
2.8 Menu trees and Field Communicator Fast Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
2.8.1 Field Communicator Fast Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
3Section 3: Installation
3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
3.2 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
3.3 Installation considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
3.3.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
3.3.2 Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
3.3.3 Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
3.4 Installation procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
3.4.1 Configure security (write protect) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
3.4.2 Configure alarm direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
3.4.2 Mounting considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
3.4.3 Mount the transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
3.4.4 Process connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
3.4.5 Connect wiring and power up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
3.4.6 Conduit electrical connector wiring (option GE or GM). . . . . . . . . . . . . . . 79
3.4.7 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
3.5 Rosemount 305 and 304 Manifolds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
3.5.1 Rosemount 305 Integral Manifold installation procedure . . . . . . . . . . . . 81
3.5.2 Rosemount 304 Conventional Manifold installation procedure . . . . . . . 81
3.5.3 Manifold operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
4Section 4: Operation and Maintenance
4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
4.2 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
4.3 Transmitter calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
4.3.1 Calibration overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
4.3.2 Sensor trim overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
4.3.3 Differential pressure sensor calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
4.3.4 Static pressure sensor calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
4.3.5 Process temperature sensor calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
4.3.6 Analog calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
4.4 Transmitter functional tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
4.4.1 Flow/energy calculation verification (test calculation) . . . . . . . . . . . . . . . 97
4.4.2 Configuring fixed process variables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
4.4.3 Analog output loop test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

iii
Reference Manual
00809-0100-4803, Rev GA
Contents
September 2017
Contents
4.5 Process variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
4.5.1 Process variable tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
4.5.2 All variables tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
4.6 Field upgrades and replacements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
4.6.1 Disassembly considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
4.6.2 Housing assembly including feature board electronics . . . . . . . . . . . . . . 100
4.6.3 Terminal block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
4.6.4 LCD display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
4.6.5 Flange and drain vent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
4.6.6 SuperModule assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
5Section 5: Troubleshooting
5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
5.2 Device diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
5.2.1 HART host diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
5.2.2 LCD display diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
5.3 Measurement quality and limit status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
5.4 Engineering Assistant communication troubleshooting . . . . . . . . . . . . . . . . . . 113
5.5 Measurement troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
5.6 Service support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
6Section 6: Safety Instrumented Systems Requirements
6.1 Safety Instrumented Systems (SIS) Certification . . . . . . . . . . . . . . . . . . . . . . . . . 119
6.2 Rosemount 3051SMV safety certified identification. . . . . . . . . . . . . . . . . . . . . . 119
6.3 Installation in SIS applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
6.4 Configuring in SIS applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
6.4.1 Damping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
6.4.2 Alarm and saturation levels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
6.5 Rosemount 3051SMV SIS operation and maintenance . . . . . . . . . . . . . . . . . . . 121
6.5.1 Proof test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
6.5.2 Partial proof test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
6.5.3 Comprehensive proof test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
6.6 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
6.6.1 Visual inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
6.6.2 Special tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
6.6.3 Product repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
6.6.4 Rosemount 3051SMV SIS reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
6.6.5 Failure rate data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

iv
Reference Manual
00809-0100-4803, Rev GA
Contents
September 2017
Contents
6.6.6 Failure values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
6.6.7 Product life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
AAppendix A: Specifications and Reference Data
A.1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
A.1.1 Performance specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
A.1.2 Functional specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
A.1.3 Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
A.2 Dimensional drawings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
A.3 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
A.3.1 Rosemount 3051S MultiVariable Transmitter. . . . . . . . . . . . . . . . . . . . . . 138
A.3.2 Rosemount 300SMV housing kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
A.4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
A.4.1 Rosemount Engineering Assistant (EA) software packages . . . . . . . . . . 147
A.5 Spare parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
BAppendix B: Product Certifications
B.1 European Directive Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
B.2 Ordinary Location Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
B.3 Installing Equipment in North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
B.4 USA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
B.5 Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
B.6 Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
B.7 International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
B.8 Brazil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
B.9 China. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
B.10EAC – Belarus, Kazakhstan, Russia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
B.11Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
B.12Republic of Korea. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
B.13Combinations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
B.14Additional Certifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
B.15Installation drawings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

v
Reference Manual
00809-0100-4803, Rev GA
Title Page
September 2017
Title Page
Rosemount™3051S MultiVariable™
Transmitter
NOTICE
Read this manual before working with the product. For personal and system safety, and for optimum
product performance, make sure the contents are fully understood installing, using, or maintaining this
product.
For technical assistance, contacts are listed below:
Customer Central
Technical support, quoting, and order-related questions
United States: 1-800-999-9307 (7:00 am to 7:00 pm CST)
Asia Pacific: 65-777-8211
Europe/Middle East/Africa: 49-(8153)-9390
North American Response Center
Equipment service needs
1-800-654-7768 (24 hours—includes Canada)
Outside of these areas, contact your local Emerson™representative.

vi
Reference Manual
00809-0100-4803, Rev GA
Title Page
September 2017
Title Page
Failure to follow these installation guidelines could result in death or serious injury.
Make sure only qualified personnel perform the installation.
Explosions could result in death or serious injury.
Do not remove the transmitter cover in explosive atmospheres when the circuit is live.
Before connecting a Field Communicator in an explosive atmosphere, make sure the instruments in
the loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.
Both transmitter covers must be fully engaged to meet flameproof/explosion-proof requirements.
Verify the operating atmosphere of the transmitter is consistent with the appropriate hazardous
locations certifications.
Electrical shock could cause death or serious injury.
If the sensor is installed in a high-voltage environment and a fault or installation error occurs, high
voltage may be present on the transmitter leads and terminals.
Use extreme caution when making contact with the leads and terminals.
Process leaks could result in death or serious injury.
Install and tighten all four flange bolts before applying pressure.
Do not attempt to loosen or remove flange bolts while the transmitter is in service.
Replacement equipment or spare parts not approved by Emerson for use as spare parts could reduce
the pressure retaining capabilities of the transmitter and may render the instrument dangerous.
Use only bolts supplied or sold by Emerson as spare parts.
Improper assembly of manifolds to traditional flange can damage the device.
For safe assembly of manifold to traditional flange, bolts must break back plane of flange web
(i.e., bolt hole) but must not contact the sensor module.
Improper installation or repair of the SuperModule™assembly with high pressure option (P0)
could result in death or serious injury.
For safe assembly, the high pressure SuperModule assembly must be installed with ASTM A193 Class 2
Grade B8M bolts and either a Rosemount 305 Manifold or a DIN-compliant traditional flange.
Static electricity can damage sensitive components.
Observe safe handling precautions for static-sensitive components.
The products described in this document are NOT designed for nuclear-qualified applications. Using
non-nuclear qualified products in applications that require nuclear-qualified hardware or products may
cause inaccurate readings.
For information on Rosemount nuclear-qualified products, contact your local Emerson Sales
Representative.

1
Reference Manual
00809-0100-4803, Rev GA
Introduction
September 2017
Introduction
Section 1 Introduction
1.1 Using this manual
The sections in this manual provide information on installing, operating, and maintaining the
Rosemount™3051S MultiVariable™Transmitter (Rosemount 3051SMV). The sections are organized as
follows:
Section 2: Configuration provides instruction on commissioning and operating Rosemount 3051SMV.
Information on software functions, configuration parameters, and online variables is also included.
Section 3: Installation contains mechanical and electrical installation instructions.
Section 4: Operation and Maintenance contains operation and maintenance techniques.
Section 5: Troubleshooting provides troubleshooting techniques for the most common operating
problems.
Section 6: Safety Instrumented Systems Requirements contains identification, commissioning,
maintenance, and operations information for the Rosemount 3051S MultiVariable Safety
Instrumented System (SIS) Safety Transmitter.
Appendix A: Specifications and Reference Data supplies reference and specification data, as well as
ordering information.
Appendix B: Product Certifications contains intrinsic safety approval information, European ATEX
directive information, and approval drawings.
Models covered
The following Rosemount 3051SMV Transmitters are covered in this manual:
Table 1-1. Rosemount 3051SMV Measurement with Fully Compensated Mass and Energy Flow
Output
Measurement type Multivariable type - M
1Differential pressure, static pressure, temperature
2Differential pressure and static pressure
3Differential pressure and temperature
4Differential pressure
Table 1-2. Rosemount 3051SMV Measurement with Direct Process Variable Output
Measurement type Multivariable type - P
1Differential pressure, static pressure, temperature
2Differential pressure and static pressure
3Differential pressure and temperature
5Coplanar static pressure and temperature
6In-line static pressure and temperature

2
Reference Manual
00809-0100-4803, Rev GA
Introduction
September 2017
Introduction
1.2 Product recycling/disposal
Recycling of equipment and packaging should be taken into consideration and disposed of in accordance
with local and national legislation/regulations.

3
Reference Manual
00809-0100-4803, Rev GA
Configuration
September 2017
Configuration
Section 2 Configuration
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
Engineering Assistant installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
Flow configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7
Basic device configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 24
Detailed device configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 27
Variable configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 38
Menu trees and Field Communicator Fast Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 57
2.1 Overview
This section contains information for configuring the flow and device configuration for the Rosemount™
3051S MultiVariable™Transmitter (Rosemount 3051SMV). Engineering Assistant installation and Flow
configuration instructions apply to Engineering Assistant version 6.3 or later. Basic device configuration,
Detailed device configuration, and Variable configuration are shown for AMS Device Manager version 9.0
or later, but also include Fast Key sequences for Field Communicator version 2.0 or later. Engineering
Assistant and AMS Device Manager screens are similar and follow the same instructions for use and
navigation. For convenience, Field Communicator Fast Key sequences are labeled “Fast Keys” for each
software function below the appropriate headings. The functionality of each host as show in Table 2-1:
Note
Coplanar transmitter configurations measuring gage pressure and process temperature (measurement
5) will report as the pressure as differential pressure. This will be reflected on the LCD display, nameplate,
digital interfaces, and other user interfaces.
Table 2-1. Host Functionality
• Available
— Not available
Multivariable
type Functionality
Rosemount 3051SMV
Engineering Assistant
AMS Device
Manager
Field
Communicator
Fully
compensated
mass and energy
flow (M)
Flow Configuration • • —
Device Configuration • • •
Test Calculation • • •
Calibration • • •
Diagnostics • • •
Direct process
variable output
(P)
Device Configuration — • •
Calibration — • •
Diagnostics — • •

4
Reference Manual
00809-0100-4803, Rev GA
Configuration
September 2017
Configuration
2.2 Safety messages
Procedures and instructions in this section may require special precautions to ensure the safety of the
personnel performing the operation. Information that raises potential safety issues is indicated with a
warning symbol ( ). Refer to the following safety messages before performing an operation preceded
by this symbol.
2.3 Engineering Assistant installation
2.3.1 Engineering Assistant version 6.3 or later
The Rosemount 3051SMV Engineering Assistant 6.3 or later is PC-based software that performs
configuration, maintenance, diagnostic functions, and serves as the primary communication interface to
the Rosemount 3051SMV with the fully compensated mass and energy flow feature board.
Failure to follow these installation guidelines could result in death or serious injury.
Make sure only qualified personnel perform the installation.
Explosions could result in death or serious injury.
Do not remove the transmitter cover in explosive atmospheres when the circuit is live.
Before connecting a Field Communicator in an explosive atmosphere, make sure the instruments in
the loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.
Both transmitter covers must be fully engaged to meet flameproof/explosion-proof requirements.
Verify the operating atmosphere of the transmitter is consistent with the appropriate hazardous
locations certifications.
Electrical shock could cause death or serious injury.
If the sensor is installed in a high-voltage environment and a fault or installation error occurs, high
voltage may be present on the transmitter leads and terminals.
Use extreme caution when making contact with the leads and terminals.
Process leaks could result in death or serious injury.
Install and tighten all four flange bolts before applying pressure.
Do not attempt to loosen or remove flange bolts while the transmitter is in service.
Replacement equipment or spare parts not approved by Emerson™for use as spare parts could
reduce the pressure retaining capabilities of the transmitter and may render the instrument
dangerous.
Use only bolts supplied or sold by Emerson as spare parts.
Improper assembly of manifolds to traditional flange can damage the device.
For safe assembly of manifold to traditional flange, bolts must break back plane of flange web
(i.e., bolt hole) but must not contact the sensor module.
Improper installation or repair of the SuperModule™assembly with high pressure option (P0)
could result in death or serious injury.
For safe assembly, the high pressure SuperModule assembly must be installed with ASTM A193
Class 2 Grade B8M bolts and either a Rosemount 305 Manifold or a DIN-compliant traditional flange.
Static electricity can damage sensitive components.
Observe safe handling precautions for static-sensitive components.

5
Reference Manual
00809-0100-4803, Rev GA
Configuration
September 2017
Configuration
The Rosemount 3051SMV Engineering Assistant software is required to complete the flow
configuration.
2.3.2 Installation and initial setup
The following are the minimum system requirements to install the Rosemount 3051SMV Engineering
Assistant software:
Pentium-grade Processor: 500 MHz or faster
Operating system: Windows™Professional 7, 8.1, 10
–32-bit
–64-bit
256 MB RAM
100 MB free hard disk space
RS232 serial port or USB port (for use with HART®modem)
CD-ROM
Installing the Rosemount 3051SMV Engineering Assistant version 6.3
or later
Engineering Assistant is available with or without the HART modem and connecting cables. The
complete Engineering Assistant package contains the software CD and one HART modem with cables
for connecting the computer to the Rosemount 3051SMV (See “Ordering information” on page 138.)
1. Uninstall any existing versions of Engineering Assistant 6 currently installed on the PC.
2. Insert the new Engineering Assistant disk into the CD-ROM.
3. Windows should detect the presence of a CD and start the installation program. Follow the on-screen
prompts to finish the installation. If Windows does not detect the CD, use Windows Explorer or My
Computer to view the contents of the CD-ROM, and then double select the SETUP.EXE program.
4. A series of screens (Installation Wizard) will appear and assist in the installation process. Follow the
on-screen prompts. It is recommended the default installation settings are used.
Note
Engineering Assistant version 6.3 or later requires the use of Microsoft®.NET Framework version 4.0 or
later. If .NET version 4.0 is not currently installed, the software will be automatically installed during the
Engineering Assistant installation. Microsoft .NET version 4.0 requires an additional 200 MB of disk
space.

6
Reference Manual
00809-0100-4803, Rev GA
Configuration
September 2017
Configuration
Connecting to a PC
Figure 2-1 shows how to connect a computer to a Rosemount 3051SMV.
Figure 2-1. Connecting a PC to the Rosemount 3051SMV
A. Power supply
B. HART modem
1. Remove the cover from the field terminals side of the housing.
2. Power the device as outlined in “Connect wiring and power up” on page 75.
3. Connect the HART modem cable to the PC.
4. On the side marked “Field Terminals,” connect the modem mini-grabbers to the two terminals
marked “PWR/COMM.”
5. Launch the Rosemount 3051SMV Engineering Assistant. For more information on launching
Engineering Assistant, see “Launching Engineering Assistant” on page 9.
6. Once the configuration is complete, replace cover and tighten until metal contacts metal to meet
flameproof/explosion-proof requirements. See “Cover installation” on page 69 for more information.
Rosemount 3051SMV without
optional process temperature
connection
Rosemount 3051SMV with optional
process temperature connection
A
RL ≥ 250Ω
B
A
RL ≥ 250Ω
B

7
Reference Manual
00809-0100-4803, Rev GA
Configuration
September 2017
Configuration
2.4 Flow configuration
2.4.1 Rosemount 3051SMV Engineering Assistant 6.3 or later
The Rosemount 3051SMV Engineering Assistant is designed to guide the user through the setup of the
flow configuration of a Rosemount 3051SMV. The flow configuration screens allow the user to specify
the fluid, operating conditions, and information about the primary element including the inside pipe
diameter. This information will be used by the Rosemount 3051SMV Engineering Assistant to create the
flow configuration parameters that can be sent to the transmitter or saved for future use.
Figure 2-2 shows the path in which the Rosemount 3051SMV Engineering Assistant will guide the user
through a flow configuration. If a natural gas, custom liquid, or custom gas option is chosen, an extra
screen will be provided to specify the gas composition or fluid properties.
Figure 2-2. Flow Configuration Flowchart
NOTICE
To ensure correct operation, download the most current version of the Engineering Assistant software
at Emerson.com/Rosemount-Engineering-Assistant-6.
Start
Process fluid
selection
Natural gas Custom liquid
Custom gas
Custom gas or
custom liquid
fluid properties
Natural gas
composition
Fluid properties
(optional)
Database liquid
Database gas or
steam
Primary
element
selection
Save/Send
flow
configuration
Ideal gas

8
Reference Manual
00809-0100-4803, Rev GA
Configuration
September 2017
Configuration
Online and offline mode
The Engineering Assistant software can be used in two modes: online and offline. In online mode, the
user can receive the configuration from the transmitter, edit the configuration, send the changed
configuration to the transmitter, or save the configuration to a file. In offline mode, the user may create a
new flow configuration and save the configuration to a file or open and modify an existing file.
2.4.2 Basic navigation overview
Figure 2-3. Engineering Assistant Basic Navigation Overview
The Engineering Assistant software can be navigated in a variety of ways. The numbers below correspond to the numbers shown in
Figure 2-3.
A. The navigation tabs contain the flow configuration information. In offline mode, each tab will not become active until the
required fields on the previous tab are completed. In online mode, these tabs will be functional unless a change on a preceding
tab is made.
B. The Reset button will return each field within all of the flow configuration tabs (Fluid Selection,Fluid Properties,and Primary
Element Selection) to the values initially displayed at the start of the configuration.
a. If editing a previously saved flow configuration, the values will return to those that were last saved.
b. If starting a new flow configuration, all entered values will be erased.
C. The Back button is used to step backward through the flow configuration tabs.
D. The Next button is used to step forward through the flow configuration tabs. The Next button will not become active until all
required fields on the current page are completed.
E. The Help button may be selected at any time to get a detailed explanation of the information required on the current
configuration tab.
F. Any configuration information that needs to be entered or reviewed will appear in this portion of the screen.
G. These menus navigate to the Configure Flow, Basic Setup, Device, Variables, Calibration, and Save/Send tabs.
H. These buttons navigate to Config/Setup, Device Diagnostics, or Process Variables sections.
A
BCDE
G
H
F

9
Reference Manual
00809-0100-4803, Rev GA
Configuration
September 2017
Configuration
2.4.3 Launching Engineering Assistant
Flow configuration for the Rosemount 3051SMV is achieved by launching the Engineering Assistant
Software from the START menu. The following steps show how to open the Engineering Assistant
Software, and connect to a device:
1. Select the Start menu > All Programs > Engineering Assistant. Engineering Assistant will open to
screen as shown in Figure 2-4.
2. If working offline, select the Offline button located on the bottom of the screen as shown in
Figure 2-4.
OR
If working online, select the Search button located on the lower right corner of the screen as shown in
Figure 2-4. Engineering Assistant will begin to search for online devices. When the search is
completed, select the device to communicate with and select Receive Configuration button.
The HART Master Level can be set to either primary or secondary. Secondary is the default and should be
used when the transmitter is on the same segment as another HART communication device. The COM
Port and device address may also be edited as needed.
Figure 2-4. Engineering Assistant Device Connection Screen
2.4.4 Preferences
The Preferences tab, shown in Figure 2-5 on page 10, allows the user to select the preferred engineering
units to display and specify flow configuration information.
Select the preferred engineering units. If units are needed other than the default U.S. or S.I. units, use
the Custom Units setting. If Custom Units are selected, configure the Individual Parameters using the
drop-down menus.
Unit preferences selected will be retained for future Engineering Assistant sessions. Check the box to
prevent the Preferences tab from being automatically shown in future sessions. The Preferences are
always available by select the Preferences tab.

10
Reference Manual
00809-0100-4803, Rev GA
Configuration
September 2017
Configuration
Figure 2-5. Preferences Tab
2.4.5 Fluid selection for database liquid/gas
The Fluid Selection tab (see Figure 2-6) allows the user to select the process fluid.
Figure 2-6. Fluid Selection Tab

11
Reference Manual
00809-0100-4803, Rev GA
Configuration
September 2017
Configuration
Note
The following example will show a flow configuration for an application with database gas air as the
process fluid and a Rosemount 405C Conditioning Orifice Plate as the primary element. The procedure
to configure an application with other fluids and other primary elements will be similar to this example.
Natural gases, custom liquids, and custom gases require additional steps during the configuration. See
“Other fluid configurations” on page 18 for more information.
1. Engineering Assistant may open to the Preferences tab. Using the tabs at the top of the screen,
navigate to the Fluid Selection tab.
2. Expand the Gas category (select the +icon).
3. Expand the Database Gas category.
4. Select the appropriate fluid (Air for this example) from the list of database fluids.
Figure 2-7. Fluid Selection Tab - Database Gas Air
5. Enter the Nominal Operating Pressure, select the Enter or Tab key.
Note
The nominal operating pressure must be entered in absolute pressure units.
6. Enter the Nominal Operating Temperature, select the Enter or Tab key. Engineering Assistant will
automatically fill in suggested operating ranges, as shown in . These values may be edited as needed
by the user.
7. Verify the Reference Conditions are correct for the application. These values may be edited as needed.
Note
Reference pressure and temperature values are used by Engineering Assistant to convert the flow rate
from mass units to mass units expressed as standard or normal volumetric units.
8. Select Next > to proceed to the Fluid Properties tab.

12
Reference Manual
00809-0100-4803, Rev GA
Configuration
September 2017
Configuration
Table 2-2. Liquids and Gases Database
1,1,2,2–Tetrafluoroethane Acrylonitrile Formaldehyde Nitrous Oxide
1,1,2–Trichloroethane Air Formic Acid Nonanal
1,2,4–Trichlorobenzene Allyl Alcohol Furan n–Butane
1,2–Butadiene Ammonia Helium–4 n–Butanol
1,2–Propylene Glycol Aniline Hydrazine n–Butyraldehyde
1,3–Propylene Glycol Argon Hydrogen n–Butyronitrile
1,3,5–Trichlorobenzene Benzene Hydrogen Chloride n–Decane
1,3–Butadiene Benzaldehyde Hydrogen Cyanide n–Dodecane
1,4–Dioxane Benzyl Alcohol Hydrogen Peroxide n–Heptadecane
1,4–Hexadiene Biphenyl Hydrogen Sulfide n-Heptane
1–Butene Bromine Isobutane n–Hexane
1–Decanol Carbon Dioxide Isobutylbenzene n-Nonane
1–Decene Carbon Monoxide Isohexane n–Octane
1–Dodecanol Carbon Tetrachloride Isoprene n–Pentane
1–Dodecene Chlorine Isopropanol Oxygen
1–Heptanol Chlorotrifluoroethylene Melamine Pentafluoroethane
1–Heptene Chloroprene Methane Phenol
1–Hexadecanol Cycloheptane Methanol Propane
1–Hexene Cyclohexane Methyl Acrylate Propadiene
1–Octanol Cyclopentane Methyl Ethyl Ketone Pyrene
1–Octene Cyclopentene Methyl Vinyl Ether Propylene
1–Nonanol Cyclopropane m–Chloronitrobenzene p-Nitroaniline
1–Pentadecanol Decanal m–Dichlorobenzene Sorbitol
1–Pentanol Divinyl Ether Neon Styrene
1–Pentene Ethane Neopentane Sulfur Dioxide
1–Undecanol Ethanol Nitric Acid Toluene
2,2–Dimethylbutane Ethylamine Nitric Oxide Trichloroethylene
2–Methyl–1–Pentene Ethylbenzene Nitrobenzene Vinyl Acetate
Acetic Acid Ethylene Nitroethane Vinyl Chloride
Acetone Ethylene Glycol Nitrogen Vinyl Cyclohexane
Acetonitrile Ethylene Oxide Nitrogen Trifluoride Vinylacetylene
Acetylene Fluorene Nitromethane Water