Rosenberger 60S1C7-C03 User manual

Installation Instruction
for ½” annular corrugation cable
MA_1C7-C03_U
Rosenberger Hochfrequenztechnik GmbH & Co. KG
P.O.Box 1260 D-84526 Tittmoning Germany
www.rosenberger.de
Tel. : [phone]
Email : [email protected]
Page
1 / 2
RF_35/06.10/1.0 Dieses Dokument ist urheberrechtlich geschützt ● This document is protected by copyright ● Rosenberger Hochfrequenztechnik GmbH & Co. KG
60S1C7-C03
60K1C7-C03 53S1C7-C03 53K1C7-C03 64S1C7-C03
64K1C7-C03
Torque Wrench
acc. to series
A)
SLZ0002-000
SLT001-C03
 Cut your cable with tool of picture A)
 Straighten the first 200mm of the cable.
SLZ0009-000
SLZ0009-001
SLZ0009-003
1) Insert the cable into the jacket stripping
tool and remove about 20 mm of the
cable jacket.
2) Insert the cable into the jacket cutter,
annular nose in cable groove and cut
the
j
acket and cable outer conducto
r
.
3) Remove cable jacket until the mark
done by the jacket blade.
4) Control the cut surfaces 5) Remove the cable outer conductor and
dielectric. Tool: 99W057-000
-001
6) If needed, clean the cable inner
conductor with stripper, avoid any
damages, scratches on the inner
contact. Tool: SLT004-000
7) mark inner conductor by means of
gauge : SLT009-000
8) cut the inner conductor at the marked
position. Tool: 99W057-003
9) Sharpen the inner conductor of the
cable with the striping tool.

Installation Instruction
for ½” annular corrugation cable
MA_1C7-C03_U
Rosenberger Hochfrequenztechnik GmbH & Co. KG
P.O.Box 1260 D-84526 Tittmoning Germany
www.rosenberger.de
Tel. : [phone]
Email : [email protected]
Page
2 / 2
RF_35/06.10/1.0 Dieses Dokument ist urheberrechtlich geschützt ● This document is protected by copyright ● Rosenberger Hochfrequenztechnik GmbH & Co. KG
10) Deburr the inner conductor with brush
and control the roundness of outer
conductor
11) Check the dimensions
Serie X
N and 7-16 7
4.3-10 4
12) Slide back nut onto the cable until it is
completely seated. Please loose sealing
nut slightly (not complete) in order to
easily install the back nut.
13) Press clamp ring on outer conductor. 14) Expanding outer conductor on one
point with a screwdriver.
15) Insert center conductor into flaring tool´s
hole marked with ½”, start in expanded
point then press and spin the tool to
flare outer conductor.
16) Proper shape after flaring operation.
Please don´t hurt inner contact. Push
back nut until clamp ring slides into
the back nut.
17) clean the cable end with brush,
alcohol and compressed air.
18) Put connector head by hand onto the
cable and fix it with the back nut by
hand.Only turn the back nut, not the
connector head.
19) Tighten connector head and back nut
with wrenches until stop.
(Recommended torque: 18-22Nm;
Proof torque 25Nm)
20) Tighten sealing nut with wrenches
(Recommended torque: 5-8Nm;
Proof torque: 15Nm)
Link for Video: https://www.youtube.com/watch?v=yMMhysZPvB0
Draft Date Approved Date Rev. Engineering change number Name Date
J. Gramsamer 13.08.2017 R. Fang 14.11.2018 c00 18-2094 Fl. Öllerer 14.11.2018