Rosslare ME-1015 User manual

ME-1015
Enclosure for Networked Access Controllers
Installation Manual
1
1. Introduction
The ME-1015 power management enclosure is a lockable metal
cabinet for indoor use supporting Rosslare’s AC-215x, AC-225x, and
AC-425x, networked control panels.
The ME-1015 enclosure has a Universal Power Socket (UPS) with a
C14 standard plug for the VAC switcher power supply, as well as an
audio speaker sounder for chime, bell, and siren.
The ME-1015 has a VDC power management board with charger for
a 12 V / 7 Ah lead acid battery, and output power supply.
The unit has a LED illumination bar that is connected to the
controller boards and lights when the enclosure door is open. The
illumination bar includes a green power status LED and a tamper
switch at the front of the enclosure. With the built-in pre-wired
tamper switch, an event is generated and sent to the AxTraxNG™
server any time the main cover is opened.
Figure 1: ME-1015 Door Open and Locked
2. Technical Specifications
2.1 Electrical Characteristics – Power
Enclosure Input: 100 to 240 VAC, 1.6 A, 50–60 Hz,
switch mode power management board
C13 power cord
Switching Power Supply Output: 15 VDC,
4 A
PM-10 PCBA Input Power 15 VDC, 2 A, regulated power
management board
Backup Battery 12 V sealed lead acid (SLA) up to 7 Ah
Automatic Charging Circuit @ 300mA
Power switches to UPS Mode when mains
fail
PM-10 PCBA Output Power Channel 1: 13.8 VDC @ 2 A for
panel/readers
Channel 2: 13.8 VDC @ 2 A for locks
Channels are physically isolated and
fused with PTC resettable fuse
LED Indicators 1 red LED for each power output, lights
when the power is active
2.2 Electrical Characteristics – Others
Lightbar™ Current Consumption 10 mA – 10 LED light (white LED) – 0.3 W
Built-In Speaker 0.5 Watt – 8 Ohm
Tamper Switch
Normally Open (closed when cover is
closed)
2-Wires – Built in to the light bar
Power Logic States
Main Power – Restored
Main Power – Failed
UPS Battery – No UPS battery detected
UPS Battery – UPS mode started
UPS Battery – UPS mode ended
UPS Battery – UPS low battery (30%)
2.3 Environmental Characteristics
Operating Environment Indoor
Operating Temp. Range 0°C to 50°C (32°F to 122°F)
Operating Humidity Range 0 to 85% (non-condensing)
2.4 Physical Characteristics
Enclosure Dimensions
(H x W x D)
364 x 264 x 87.4 mm
(14.3 x 10.4 x 3.4 in.)
Enclosure Weight* 3.4 kg (7.5 lb)
* For weight purposes, the ME-1015 enclosure includes the metal box, AC
input, DC output and LED bar.

2
3. Installation
The installation shall be in accordance with US National Electrical
Code NFPA 70.
3.1 Mounting the ME-1015
When selecting an area for mounting, ensure the location is flat.
To mount the ME-1015:
1. Drill holes in the wall, using the hole locations on the back cover
of the enclosure as a guide (Figure 2).
Figure 2: ME-1015 Drill Holes
2. Insert masonry anchors into the drilled holes.
3. Mount the enclosure onto the wall.
4. Once the ME-1015 is mounted, it can house a controller along
with an expansion.
3.2 Connecting a Control Panel or Expansion
The ME-1015 is compatible with the following control panels.
AC-215x
AC-225x with MD-D02B
AC-425x with MD-D04B
To connect the networked control panel:
1. Make sure the main power is disconnected and the backup
battery is disconnected.
2. Mount the control panel in the mounting holes and secure it with
the provided screws.
3. Conect the power black (-) output from the PM-10 power output
to the control panel (-) and thr red (+) to the (+) terminal of the
control panel.
4. Connect the power monitoring outputs from the ME-1015 to the
control panel inputs.
5. Connect the speaker connector to the speaker output port of the
control panel.
For best practice, make sure that power is completely turned off
when installing peripherals, locks, and other accessories to the
control panels.
3.3 9BConnecting the Battery
Once the control panel connections are completed, you can install
the battery.
To connect the battery:
1. Make sure the main power is disconnected when installing the
battery.
2. Use a 7 Ah sealed lead acid battery with crimp terminals (Yuasa
Model NP7-12FR or equivalent).
3. Connect the backup battery red/black wires.
If there is residual power in the battery, the system should turn
on. If the battery is totally empty, the system will not power on.
4. Plug the power cord in to the slot located on the bottom left of
the ME-1015 casing and secure it if needed.
3.4 10BPowering on the ME-1015
To power on the ME-1015:
1. Make sure that all of the connections are secure.
2. Plug the power cord in to the slot located on the bottom left of
the ME-1015 casing and secure it if needed.
3. Check that the green power status LED lights.
4. Thread the wires through the designated holes in the rear and
sides of the enclosure.
5. Wire the board to its inputs/outputs according to the wiring
instructions for the relevant board (see Appendix A.)

3 0706-0960650+01
A. Related Documents
AC-215x-B Series Hardware Installation and User Manual (PN: 0706-0960661+00)
AC-225x-B Series Hardware Installation and User Manual (PN: 0706-0960660+00)
AC-425x-B Series Hardware Installation and User Manual (PN: 0706-0960668+00)
Limited Warranty
The full ROSSLARE Limited Warranty Statement is available in the
Quick Links section on the ROSSLARE website at
www.rosslaresecurity.com.
Rosslare considers any use of this product as agreement to the
Warranty Terms even if you do not review them.
Contact Information
United States and Canada
Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]
Europe
Rosslare Israel Ltd.
22 Ha'Melacha St., P.O.B. 11407
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]
Latin America
Rosslare Latin America
Buenos Aires, Argentina
[e-mail]
China
Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]
Asia Pacific, Middle East, Africa
Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]
India
Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]
CERT
ISO 9001
ISO 14001