Rototherm AM60 User manual

Instruction Manual
CO2 Monitor-AM60
CO2/TEMP/RH
www.rototherm.co.uk

1
1
1
2
3
4
3
5
6
7
8
9
14
15
17
Contents
Getting Started
Packing List
Features at a Glance
Overview
General Operation and Settings
Restore Factory Defaults
Switch On/Off
Power Source
LCD Display
Trend Chart Display
Max/Min
Main Menu Functions
RH/TEMP Calibration
Specifications
Appendix

Features at a Glance
- Large Display
- Touch Button Operation
- 15° Bevel Design, Easy to Read
- Low Drift NDIR Sensor, Long Lifespan
- Audible Alarm
- Chart with Variable Time Zoom Levels
- CO2/RH/Temperature Monitor Tracer
- CO2 Auto-Calibration and Manual Calibration
- Temp and RH Manual Calibration
- Max/Min Value Display in Certain Time
- Built-in Backup Battery
Thanks for purchasing our desktop CO2 monitor! This product is used to monitor
CO2 concentration, RH, and temperature for indoor air quality monitoring.
Getting Started
Packing List
CO2 Monitor Unit
USB Cable for Power
User’s Manual
AC Adapter (Optional)
1

Overview
Drawing Sketch and Components List
1
3
4
5
6
8
7
10
11
9
2
1
3
4
5
6
8
7
2
11
12
13
14
15
16
10
9
Front Panel
LCD
UP Button
Down Button
Menu Button
Enter/OK Button
Battery Indicator
Red Condition Indicator
Orange Condition Indicator
Green Condition Indicator
USB Port
Hole for Buzzer
Hole for Rope
Hole for Screws
ON/OFF Switch
Label
Item ItemDescription Description
12 13 14
16
15
2

- Press down the switch on the back to activate this monitor. After 3 minutes'
warm-up, your device is ready for use. See details in Page 4.
- Use the provided USB cable to connect the device for charging. See detail in Page 5.
- Use and buttons to switch timeline and CO2/RH/TEMP. The trend chart
displays the history records for any of the three parameters. See detail in Page 7.
- Press once will bring up the main menu. To select the function, press /
button. See detail in Page 9.
- Select to switch human and plants modes. See detail in Page 10.
- Enter to switch alarm and mute . See detail in Page 10.
- Select to change the high/low alarms for human and plant . See detail in
Page 13.
- Enter to switch temperature units C and F. See detail in Page 12.
General Operation and Settings
Restore Factory Defaults
In Detection Panel , hold for 4 seconds until an audible beep is heard.
3

Press down the switch to activate this monitor, wait for 3 minutes for warm-up.
Press the switch again to switch it off.
Switch On/Off
Switch on:
Switch off:
Switch it off if you don't use it for more than 1 week.
4

Power Source
Plug in USB power
When the device is ON, plug in USB cable power
Battery
Battery indicator
Charging: flashing green indicator
Fully charged: steady green indicator
Battery recharging
When the device is ON, plug in USB cable power
Charging time: 6 hours (Charge extra 30 minutes after the indicator turning from red to green)
Working time: ≥12 hours
5

19
20
21
22
23
24
25
26
27
ItemItem Name Name
CO2/RH/TEMP Chart
Max Reading of Chart
Min Reading of Chart
RH Reading
Main Menu
CO2 Reading
Time per Division- indicates the
Plant Mode
Human Mode
Audible Alarm On/Off
17
18
Temperature Reading C / F
o o
LCD Display
chart’s span of time
17
18
19
20
21
22
23
24
25
26
27
6

The below chart displays the past readings for any of the three parameters (CO2/RH
/Temp). There are 4 modes that can be toggled by using key: CO2, TEMP, RH,
and Cycle(automatically cycles through CO2/Temp/RH).
Press will toggle the available Zoom Levels for each parameters.(Minute/Hour/
Day/Week)
Trend Chart Display
Press Press Press
Press
Press
Press
Press
Press
7

Zoom Level (Time Span) Time per Division
1M(minute) 5sec /div
1H(hour) 5m/div
1D(day) 2h/div
1W(week) 0.5d/div
Max/Min
Below is a table that shows the available Zoom Levels for all parameters CO2/RH/
Temp,as well as the duration of each division for corresponding Zoom Levels:
At the top right corner of the display, there are two numerical indicators: MAX and
MIN.As the Zoom Level is changed, the MAX and MIN values will reflect the
maximum and minimum values on the chart of the selected parameter(CO2, RH
and Temp).
8