Roule RL-09IDP1 User manual

Version 1.0
MODEL:RL-09IDP1
VIDEO DOORPHONE
USER MANUAL

1 2
Product Description
Features
The RL-09IDP1 can be used to call, intercom, monitor and unlock etc.
It is a product that is very suitable for single house, villa, hotel and
office etc, giving you the combined benefit of security and convenience.
Package Contents
Indoor unit x1 Outdoor unit x1 Embedded box
Rain shade
Adapter x1 Bracket x1 15m cable x1 Screw pack x1
1. 7 inch TFT screen with low power consumption, no radiation and
high definition.
2. Ultra thin designed touch key pad indoor unit for fashionable and
luxury life.
3. Touch pad operation on outdoor unit, ID card unlocking function.
4. Electric lock release function.
5. Photo taking and photo browsing function.
6. Monitoring the outside.
7. 16 pieces of chord ringtones for option.
8. Chinese and English for language option.
9. Melody volume, talking volume, brightness and chroma are adjustable.
10. The indoor unit can be hung on the wall.
Enclosed with an adapter and 15m cable for DIY installation.
CONTENTS
Product Description..................................... 2
Features..................................................... 2
Technical Specification................................. 9
Wiring Diagram........................................... 5
Function Keys and Operation Instruction....... 6
Package Contents.................................. 2
Safety Instruction........................................ 3
System Installation...................................... 3
Trouble Shooting ......................................... 10
ID cards

34
B.Outdoor Unit
1). Install the foam on the back of the box, and then fasten embedded
the box on the wall with screws (4x30BA). The size is embedded
85(W) ×148(H) ×42(D) mm
2). Install the outdoor unit on the door at 1.4m~1.7m high from the ground
(according to the camera's effect), avoid direct sunlight.
3). Fasten the outdoor unit on the wall with enclosed screws.
1. 4～1 .7米
对讲距离约40cm内
1. Embedded box installation
1) Fasten the rain shade on the wall with the enclosed screws.
(screw size: 4x30BA)
2. Rain shade installation
1. 4～1 .7米
对讲距离约40cm内
2) Install the outdoor unit at the height of 1.4m~1.7m up from the ground
(according to the camera's effect), avoid direct sunlight.
3) Install the square nut (M3) into the groove on the bottom of the rain shade,
and then put the outdoor unit into the rain shade, use the hex screws
(M3X10) to fasten the outdoor unit in the rain shade and then tighten it with
a spanner.
2. Finish wire connection according to the wiring diagram, and then hang
the indoor unit on the bracket.
System Installation
A. Indoor Unit
1. Fasten the bracket on the wall with screws.Use 4x40PM screws to install
it on the 86 standard box.Use 4x30BA screws to install it on the wall.
Safety Instruction
1. Do not install the indoor unit in high temperature or high humidity
environment.
2. Keep the indoor unit away from the TV, otherwise the signals the TV
and the intercom use may interfere with each other.
3. Do not touch the unit with wet hands.
4. Clean the camera or screen with a soft cloth. Do not use detergent,
thinner, volatile or corrosive liquid.
5. Avoid throwing, dropping or hitting the units.
6. Do not expose the camera of the outdoor unit under direct sunlight.
7. Use the products under the circumstance of barrier-free and no
interference.
Caution
1. To prevent damage, the units should be fastened on the wall
according to instruction.
2. Power plug as disconnecting device should be kept convenient to
operate.

5 6
Function Keys and Operation Instruction
A. Indoor unit
B.Outdoor unit
Speaker
Melody volume
(H/M/L)
Melody Selection
Brightness
Chroma
Talking volume
Microphone
Down
Unlock
Up
Monitor/Talk
Wiring terminal
Menu
Microphone
Call
Infrared light
Rain shade
Speaker
Card
swiping
area
Camera
Adjust lever
Wiring terminal
1. The enclosed cable is 15m, RVV6x0.5m㎡ cable can be used if you
want to lengthen it to . Please use RVV2x1.0m㎡ cable to 15m~30m
connect the electric lock.
2. Connect the terminal 1\2\3\4\5\6 of the indoor unit with the terminal
1\2\3\4\5\6 of the outdoor unit respectively. Connect the 7\8 terminal
of the indoor unit with the electric lock through RVV2x1.0m㎡ cable.
The unlock cable shall be no longer than 15m; otherwise the unlocking
function may be interfered.
Wiring Diagram
Diagram A：
Diagram B：
Wiring instruction
1、Audio
2、Ground
3、Video
4、Power
5、Card reader power
6、Unlock
1 2 3 4
5 6
DC12V AC100-240V
50HZ/60HZ
Indoor Unit
1 2 3 4 5 6 7 8
Electric lock
7 8
Wiring instruction
1、Audio
2、Ground
3、Video
4、Power
5、Card reader power
6、Unlock
1 2 3 4
5 6
DC12V AC100-240V
50HZ/60HZ
1 2 3 4 5 6 7 8
7 8
Indoor Unit
Electric lock
Electric lock

7 8
Menu Operation
Press the MONITOR/TALK( ) button to turn on the screen, press the
MENU button to enter OSD menu.
Menu
Melody volume
Language
Date
Time
Delete All
Exit
Melody selection
Brightness
Chroma
Talking volume
1. Visitors press the CALL button on the outdoor unit, the indoor unit will
ring and display the picture of the visitor, and photos will be taken and
saved automatically. Press the MONITOR/TALK( )button on the
indoor unit to talk with the visitor, the talking time is about 120s.
2. Max 50 photos can be saved, the former photos will be overwritten
automatically by the new taken photos when the storage is full.
3. Under monitoring or talking state, press the UNLOCK( ) button on
the indoor unit to release the electric lock.
4. Press MONITOR/TALK( ) button to monitor the outside, the
monitoring time is about 40s, press it again to talk with the visitor, the
talking time is about 120s, press MONITOR/TALK( ) button again
to exit after finishing the conversation.
5. Adjust the BRIGHTNESS( ), CHROMA( ) and TALKING
VOLUME( ) through the buttons on the indoor unit respectively.
The MELODY VOLUME can be set to H/M/L through the button on the
indoor unit.
6. Under monitoring state, press MELODY SELECTION( ) to choose
the chord ringtone, there are 16 pieces ringtones for option.
7. Cards Instruction:
a. Two administrative cards (one add card and one delete card) and five
user cards have been set when delivery.
b. Add a user card: under normal mode, swipe the authorized “Add card”--
a “BI” sound ( the green point will be on)—swipe the card need to be
added—swipe the “Add card”—a “BI“ sound， then a user card is added
successfully.
c. Delete a user card: under normal mode, swipe the authorized “Delete
card”-- a “BI” sound ( the red point will be on)—swipe the card need to be
deleted—swipe the “Delete card”—a “BI” sound， then a user card is
deleted successfully.
Photo Browsing
1. Under standby mode, press UP/DOWN button to browse the photos.
2. It will exit automatically if no operation is done in 10s.
Time
01:01:46
Language
Language
Press Menu button to the select the interface. Press
Up/Down button to select Chinese or English as the language.
Date
Press Menu button to select the interface. Press Up/Down
button to enter Date Setting . the selected one to be set will be
flashing, press the MENU button to move to next setting one and press the
UP/DOWN button to adjust the value.
Date
2013-01-01
Time
Delete All
Exit
Press Menu button to select the interface . Press Up/Down
button to enter time Setting . The selected one to be set will be
flashing, press the MENU button to move to next setting one and press the
UP/DOWN button to adjust the value.
Press Menu button to select the interface. Press
Up/Down button to enter Delete state . It will exit automatically after
finished.
Delete All
Deleting
>.......
Press Menu button to select the interface. Press Up/Down
button to exit OSD menu.
Exit

910
B.Outdoor unit
Infrared working Distance
Working Temperature
Resolution
Illumination
Viewing Angle
>4m
-15℃～+50℃
>500 TV lines (CMOS)
2LUX
60° wide angle
Outline Dimension 11220051 mm
Technical Specification
Indoor Unit
Adapter Input Voltage
Adapter Output
Voltage & Current
AC110~240V 50Hz/60Hz
Screen Size
Resolution
Pixel Dimension
Effective Area
7 inch
800(H)*480(V)
154.08 (H)86.58 (W) mm
0.0642(H)  0.1790(V) mm
Outline Dimension 22812921 mm
120S±10%
30m (4x0.5m㎡)
Static State<2.5W, Talking state<7.5W
40S±10%
Relative Humidity 10%~90% (RH)
-10+40
Talking Time
Monitoring Time
Effective Distance
Power Consumption
Working Temperature
DC12V 1100mA
Trouble Shooting
Problem
No Picture/Signal
·Make sure all the connections are secure and
properly connected.
·Make sure your monitor is plugged into a power
source.
·Make sure there is nothing obstructing the view
o f t he c amera.
Solutions
No Picture,
but intercommunication
is normal
No audio when calling
The outdoor unit cannot
call the indoor one
Door Unlock not
Functioning
No one can hear me
outside but I can hear
them after calling
No one can hear me
outside but I can hear
them when monitoring
·Make sure all the connections are secure and
properly connected.
·Make sure there is nothing obstructing the view
of the camera.
·Make sure the volume noch on the indoor unit is
turned up.
·Make sure there is nothing interfering with
the speaker or microphone on the indoor unit
or the camera.
·Make sure all the connections are secure and
properly connected.
·Make sure all the connections are secure and
properly connected.
·Make sure the connections with the locks are
secure and properly connected.
·Make sure you have the lock wired to a power
source which is enough to make it operate.
·Press TALK key for two-way intercom.
·Make sure all the connections are secure and
properly connected.
·Press TALK key for two-way intercom Since
simple touch MONITOR allows you to see and
hear outside but prevents the outside from
hearing you
·Make sure all the connections are secure and
proper ly connected