Rowley R-TEC Automation ARC Motor Programming User manual

© 2021 Rowley®Company. All rights reserved. R-TEC Automation®is a registered trademark of the Rowley®Company, LLC. 1
ARC Motor Programming - Quick Start Guide
Please read these instructions prior to starting. The instructions for the hard wired and battery ARC motor are the same.
Check if the remote is unlocked. Limits cannot be changed with a locked remote.
SETTING MODESOVERVIEW -
Hold P1 button on motor head.
The P1 button is utilized to administer motor configurations as described below.
Drapery Large Tubular
P1 Locations on Motors
Internal Tubular
Hold P1 button on motor head.
Select a channel (15)
on the controller. Hold STOP on controller.
Motor Response
Approx.
Motor Response
PAIR MOTOR WITH CONTROLLER
Approx.
1
Reset to Factory Settings
Reverse Direction
Sleep Mode
Activate Pairing Mode Approx.
Approx.
Approx.
Approx.

© 2021 Rowley®Company. All rights reserved. R-TEC Automation®is a registered trademark of the Rowley®Company, LLC. 2
Motor Response
Approx.
CHANGE MOTOR DIRECTION
To reverse travel direction, hold both UP and DOWN on controller.
SET TOP LIMIT
To save upper limit,
hold UP and STOP.
To save lower limit,
hold DOWN and STOP.
Approx.
Motor Response
5
ADJUST LOWER LIMIT
4
3
Move shade to the desired lowest
position by pressing the DOWN button.
To save lower limit,
hold DOWN and STOP.
Hold DOWN and STOP
on the controller.
Approx.
Motor Response
5
Approx.
Motor Response
5
ADJUST UPPER LIMIT
5
Move shade to the desired highest
position by pressing the UP button.
To save upper limit,
hold UP and STOP.
Hold UP and STOP
on the controller.
Approx.
Motor Response
5
Approx.
Motor Response
5
2

© 2021 Rowley®Company. All rights reserved. R-TEC Automation®is a registered trademark of the Rowley®Company, LLC. 3
SET / DELETE A FAVORITE POSITION
6
Press STOP on controller. Press STOP on controller.Press P2 on controller.
Motor ResponseMotor Response Motor Response
STEP MODE
7
Default motor mode is Roller after initial Limits have been set, use following steps to change to Step Mode.
If motor is in Step Mode, use following steps to change to Roller Mode.
Hold UP and DOWN on the controller.
Hold UP and DOWN on the controller.
Press STOP.
Press STOP.
Approx. 5
Approx. 5
Motor Response
Motor Response
Motor Response
Motor Response

© 2021 Rowley®Company. All rights reserved. R-TEC Automation®is a registered trademark of the Rowley®Company, LLC. 4
ADJUST MOTOR SPEED
9
Press UP on controller. Press UP on controller.Press P2 on controller.
Motor ResponseMotor Response Motor Response
CREATE / DELETE GROUPS USING P2
8
A = Existing switch or channel (to keep). B = Switch or channel to add or remove.
Press P2 on
existing switch.
Press P2 a second time on
existing switch.
Press P2 on new switch
or remote controller.
Motor ResponseMotor ResponseMotor Response
LOCK REMOTE
10
Response
LED solid on when locked
LED blinking when unlocked
Response
LCD displays “L” when locked
LCD displays “U” when unlocked
1 Channel15 ChannelTo switch modes hold
right button
for 5 Seconds Pressing the right button for 1 second or less will display the current mode

© 2021 Rowley®Company. All rights reserved. R-TEC Automation®is a registered trademark of the Rowley®Company, LLC. 5
Any Questions?
Contact our R-TEC Automation®in-house experts at 866.985.3423. Email us at [e-mail].
HIDE CHANNELS - 15 CHANNEL REMOTE ONLY
11
Your multi channel remote can be configured to have anywhere between 1 or 15 visible channels.
Inactive channels will not be visible when scrolling through the CH selection.
Hold STOP and CH.
Continue holding CH or
Continue holding CH and
press STOP to confirm.
Continue holding CH and select required
channel quantity by pressing UP or DOWN.