Rowlinson Garden Products 4x6 Overlap Double Door Shed User manual

Assembly Instructions
4’x6’ Overlap
Double Door Shed English SS470B
Before assembly
• We recommend that time is taken to read
the instructions before starting assembly,
then follow the easy step by step guide.
The instruction sheet is only a guide to the
assembly. Certain items may not be shown
to scale.
• Check all components prior to assembly
• This product should be assembled by no less
than two people
• Drill all components where indicated
• Gloves are recommended when handling
components
x 2 Drill Gloves
Recommended tools for assembly
• Power Drill/Screwdriver
• Cross-head drill bit
• 3mm diameter drill bit
• 6mm diameter drill bit
• 12mm diameter drill bit
• Hammer
• Sharp knife
• Spirit level
• Step ladder
No. Components Qty.
1 Floor 1
2 Side wall panel (Width 1174mm) 2
3 Back wall panel (Width 860mm) 2
4 Front panel 2
5 Apex panel 2
6Roof purlin/felt batten (Length 1200mm) 4
7 Roof panel 2
8 Roof felt roll (4m) 1
9 Door header rail (28x28x1330mm) 1
10 Door rebate strip (12x22x1715mm) 2
11 Left door (tower bolt mounting blocks) 1
12 Right door 1
13 Door coverstrip (16x45x830mm) 2
14 Coverstrips 5
15 Bargeboard 4
16 Finial 2
No. Fixing Kit Qty.
17 T-Hinge 6
18 Pad bolt 1
19 Tower bolt 2
20 Turn button 1
21 50mm coach bolt 4
22 Nut 4
23 Washer 4
24 50mm screws 34
25 32mm screws 20
26 25mm screws 55
27 19mm round head screws 12
28 30mm nails 49
29 10mm felt nails 70
1
13
1
2
1
6
1
16
1
8
1
12
1
9
1
11
1
17
1
18
1
19
1
20
1
10
1
15
1
1
1
3
1
14
1
7
1
4
1
5

1. Floor
2. Wall panels
3. Apex panels
Use this diagram to check the correct
orientation of the corners
Continue adding the remaing panels
using 3 x 50mm screws for each join.
Prepare a firm level area that is slightly larger than the floor, for the shed to sit.
To protect the floor and validate the anti-rot guarantee, adequate provision
must be made to ensure ground contact is avoided. The building must not be
allowed to sit in pooled water during wet conditions and air must be able to
circulate underneath the building. Recommended base options include either:
• Concrete pad
• Slabs
• Decking
• 50x50mm pressure treated timber bearers (minimum requirement)
Important
Important
Side panel
Back panels
Side panel
Front panels
Back panel
Side panel
Floor
Panel cladding
overhangs floor edge
Panel frames rest on
the floor
Back apex panel
Front apex panel
Drill pilot holes with a 3mm drill for
each screw in this section.
Drill pilot holes with a 3mm drill for
each screw in this section.
Drill
Apex
panel
Apex
panel
Back
panel
Front
panel
50mm
50mm
50mm
Drill
3mm
1
1
1
3
1
3
1
2
1
2
1
1
1
4
1
4
1
5
1
5

4. Door header rail & door rebate strips
6. Attach roof panels
Apex panel
bottom frame
Header rail
Fits flush to the
apex bottom
frame and wall
panel frame.
Door header rail
Door rebate
strips fit under
the header rail.
Drill pilot holes with a 3mm drill for
each screw in this section.
Drill
3mm
5. Roof panel, felt battens & purlins
30mm
Construct 2 identical
roof panel assemblies
Felt batten must be set flush to
the lower edge of the roof panel.
10mm
1
6
1
6
1
7
50mm
30mm
32mm
32mm
x7 per panel
Purlin MUST be set 10mm from
the upper edge of the roof panel
Important Important
1200mm
x7 per panel
32mm
1
9
1
10
1
10

Back panel
Side panel
7.Secure walls to floor
8.Doors & door coverestrips
Side panel
Back panels
Side panel
Front panels
Secure door coverstrips
to Right-hand door only.
Important
Drill pilot holes with a
3mm drill for each screw
in this section.
Drill pilot holes with a
3mm drill for the door
coverstrip screws.
Drill
3mm
Drill
3mm
Tower bolt
mounting block
Tower bolt
mounting block
50mm
50mm
50mm
25mm 25mm
25mm 25mm
25mm 25mm
x7 x7
x7 x7
x7 x7
25mm
25mm
1
12
1
17
1
11
1
17
1
13
1
13
1
17
1
17
1
17
1
17

10.Roof felt
Fold the felt over the
roof edge and nail to
the felt batten.
9. Padbolt, turn button & Tower bolts
ROOF FELT ROLL
must be cut into
three equal lengths.
Leave felt over hang
at front and rear.
Leave felt over hang
at front and rear.
Leave felt over hang
at front and rear.
Fold felt down at the front and rear.
Nail to the ends of the felt batten
and apex panels.
Drill hole in the floor for bolt to fit in
10mm
Felt
Nails
10mm
Felt
Nails
10mm
Felt
Nails
10mm
Felt
Nails
10mm
Felt
Nails
10mm
Felt
Nails
10mm
Felt
Nails
10mm
Felt
Nails
25mm
25mm
50mm
2”
Washer Drill
6mm
Nut
x6
x4 x4 x4
x13
x6
x6
x13
x13
x13
19mm
19mm
Drill
12mm
x4
x4
1
20
1
19
1
19
1
18
1
8

Important information - retain for future reference
Pressure treated overlap buildings require no further preservative treatment, However they can be painted or stained if required. To protect the floor and validate the
anti-rot guarantee, adequate provision must be made to ensure ground contact is avoided. The building must not be allowed to sit in pooled water during wet conditions
and air must be able to circulate underneath the building. Recommended base options include either concrete pad, slabs, decking. The minimum requirement is 50x50mm
pressure treated timber bearers.
Timber Information.
As timber is a natural material, there are certain weather conditions that may affect the materials properties. In times of excessive dry spells the material may lose some
of its internal moisture causing a certain degree of shrinkage on a panel and in periods of excessive rain there will be a certain amount of swelling throughout the wooden
panels. This process can not be avoided. If you have problems with certain boards shrinking in dry spells try to decrease the amount of direct sunlight on the building or
the amount of air passing over the building. During hot spells spray water directly onto the panels with the aid of a garden hose.
If in doubt of any aspect regarding the assembly, use or safety of your garden Building please contact us:
Help Line: (Normal Office Hours) 01829 261 121
Email: [e-mail]
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
www.rowgar.co.uk
We constantly improve the quality of our products,
occasionally the components may differ from the
components shown and are only correct at time
of printing. We reserve the right to change the
specification of our products without prior notice.
2020 © Rowlinson Garden Products Ltd
11.Coverstrips, bargeboards & finials
Coverstrips are positioned, one in
each corner and one over the join
of the two back panels.
Fit two bargeboards and a finial on
the back in the same way.
If necessary trim off any
excess roof felt.
30mm
30mm
30mm
30mm
30mm
30mm
30mm
30mm
x3
1
14
1
14
1
14
1
14
1
15
1
15
1
16
1
15
1
16
1
16
1
14