Rowlinson Garden Products Keswick Arbour User manual

2012 © Rowlinson Garden Products Ltd
290mm
445mm
1600mm
1286mm
1150mm
2074mm
600mm
800mm
90mm
90mm
1322mm
736mm
68mm 68mm
Keswick Arbour PRODUCT DIMENSIONS
DRAWING DATE: 05.04.12
DRAWING REF: PERKES PD 1

1. Seat to uprights
Drill four holes in each seat slat bearer as shown in the diagram. Position the
seat between the two uprights, 345mm from the bottom of the upright.
Secure through the drilled holes into the upright legs using 8 x 60mm screws.
2
1
3
4
5
6
2012 © Rowlinson Garden Products Ltd
Drill
7
60mm
Drill
60mm
Drill
x 2 Drill
345mm
Seat slat bearer
2. Seat back to uprights
Drill four holes in the seat back as shown in the diagram. Place the seat back
on the seat between the two uprights. Secure through the drilled holes into
the legs of the uprights using 4 x 60mm screws. Attach the seat back to the
seat bearer using a flat bracket and 4 x 25mm screws at each side.
Drill
Drill 40mm
Rafter
Roof slat
40mm
40mm
Spread slats
evenly Top view
25mm
5. Roof to uprights
Lift the rafter sections onto the rebates of the uprights. Drill two holes at each
corner of the roof as shown in the diagram, then secure the roof to the uprights
using 2 x 60mm screw per corner. Drill two holes in each diamond finial. Secure
the finials over the joins between the rafter and the uprights using 2 x 40mm
screws per finial.
60mm
Drill
6. Roof slats
Evenly spread the roof slats over the rafters and secure using 2 x 40mm nails
per slat, nail through the slats and into the rafters.
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle, Nr. Nantwich
Cheshire
CW5 6BN
Help Line (Normal Office Hours) 01829 261 121
English SS286
Assembly Instructions
Keswick Arbour
No. Components Qty.
1 Seat 1
2 Seat back 1
3 Back lattice 1
4 Uprights 2
5 Roof rafter (with dowels) 2
6 Roof rafter 2
7 Roof slat sections 2
8 Diamond finials 4
9 Triangular finials 2
No. Fixing kit Qty.
10 Flat brackets 4
11 60mm screws 24
12 40mm screws 12
13 25mm screws 16
14 40mm nails 60
We constantly improve the quality of our products, occasionally the
components may differ from the components shown and are only
correct at time of printing. We reserve the right to change the
specification of our products without prior notice.
Before assembly
•We recommend that time is taken to read the instructions before
starting assembly, then follow the easy step by step guide.
The instruction sheet is only a guide to the assembly.
Certain items may not be shown to scale.
•Check all components prior to assembly
•Drill all components where indicated.
•This product should be assembled by no less than two people.
•Never attempt to erect the assembly in high winds.
Recommended tools for assembly
•Cross head screw driver
•Drill with 2mm diameter drill bit
•Step Ladder
8
60mm
Drill
3. Back lattice to uprights
Drill four holes in the back lattice as shown in the diagram. Sit the back lattice
on the top of the seat back. Secure through the drilled holes into the legs of
the uprights using 4 x 60mm screws
IMPORTANT: RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
Periodically check all fastenings for tightness
For domestic use only
9
25mm
4. Roof rafter Assembly
Slot together one of each of the rafters using the pre-fitted dowels. join on the
back using a flat bracket and 4 x 40mm screws. Drill two holes in a triangular
finial. Secure to the front of the rafters centrally over the join using 2 x 40mm
screws. Create a second rafter section in the same way.