Rowlinson Garden Products winchester arbour User manual

Before assembly
•We recommend that time is taken to
read the instructions before starting
assembly, then follow the easy step
by step guide.The instruction sheet
is only a guide to the assembly.
Certain items may not be shown to
scale.
•Check all components prior to assembly
•This product should be assembled
by no less than two people.
•Never attempt to erect the assembly
in high winds.
•Drill all components where indicated.
Recommended tools for assembly
•Cross head screw driver
•Drill with 3mm diameter drill bit
•Step ladder
7. Finials
Hold the apex of the roof together by securing an L-bracket using 4 x 40mm screws to the underside of the front
two rafters. se the flat bracket to join the back two rafters, secure across the join on the inside of the roof using
4 x 40mm screws. Drill two holes in four finials as shown below. Attach finials over each roof and upright join, two
on the front and two on the back. Drill four holes in the remaining finials, position one on the front and one on the
back over the join of the two roof panels at the apex. se 4 x 40mm screws per finial. Attach the metal roof to the
upright legs using 2 x 30mm screws per leg as shown in the diagram.
inchester Arbour
Assembly Instructions
English SS121F
No. Components Qty.
1 Floor 1
2 Seat front 1
3 Left-hand upright 1
4 Right-hand upright 1
5 Seat 1
6 Seat back 1
7 Triangular panel 1
8 Left roof panel 1
9 Right roof panel 1
10 Coverstrip 1
11 Finial 6
No. Fixing kit Qty.
12 70mm screws 4
13 50mm screws 10
14 40mm screws 62
15 25mm black screws 16
16 L-bracket 9
17 Flat bracket 1
2
1
4
5
6
7
3
8
9
10
11
x 2 Drill
Gloves
40mm
Drill
Drill four holes in two finials and attach at
the roof apex.
40mm
40mm
25mm
Caution
Some of the arbour
components may
have sharp edges.
Wear protective
work gloves while
handling these
components.
Drill
Drill two holes in four finials and attach
over each roof and upright join.
I MPORTANT, RETAIN FOR F T RE REFERENCE: READ CAREF LLY
Periodically check all fastenings for tightness
For domestic use only
Safety information
2015 © Rowlinson Garden Products Ltd
If in doubt of any aspect regarding the assembly, use or safety of your arbour please contact us :
Help Line: (Normal Office Hours) 01829 261 121
Email: [e-mail]
ROWLINSON GARDEN PROD CTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
www.rowgar.co.uk
We constantly improve the quality of our products, occasionally
the components may differ from the components shown and are
only correct at time of printing. We reserve the right to change the
specification of our products without prior notice.

1. Seat back to uprights
Fit the back panel into the slots of the left-hand upright. Make sure the seat bearer is on the inside and that the
rebated rail is at the top. Secure together by using 3 x 40mm screws, screw through the leg of the upright, ensuring
the screw goes through the rebate in the leg and back panel, secure the seat bearers of the two panels with
L-brackets and 4 x 40mm screws per bracket. Repeat for the right-hand upright.
4. Seat
Place seat on the seat bearers with the hinges at the back. Make sure it is square and is able to open freely. Screw to
the back panel seat bearer using 4 x 50mm screws.
3. Secure floor
Secure the floor using 4 x 50mm screws, screw two through each upright into the ends of the floor framing. sing
4 x 70mm screws, screw two through the front and two through the back panel into the floor framing.
2. Seat front and floor
Fit L-brackets flush to the front end of the seat bearer on each upright as shown using 2 x 40mm screws per bracket.
Prior to fitting the seat front, have the floor in place. Lift the seat front between the uprights, ensure the inset top
frame is at the top see below diagram. Ensure the top of the panel is level with the top of the seat bearers and secure
with the L-brackets using 2 x 40mm screw per bracket. Fix the panel at the bottom by screwing through the upright
panel into the end of the framing at the bottom of the front panel using 1 x 50mm screw at each end.
40mm
Seat bearer
Rebated rail
Bottom frame
pright top frame
40mm
Top view
40mm
50mm
50mm
50mm 70mm 50mm
50mm
6. Coverstrip
Place the coverstrip on the roof apex, Drill four holes in each side and secure using 4 x 30mm black screws and
4 x 25mm black screws as shown below.
25mm
40mm
40mm
40mm
Gloves
wear protective gloves while
handling roof sections.
5. Roof assembly
Lift the triangular panel into the rebate of the seat back. Lift on the roof panels with the rebated rafters at the back of
the arbour ensure the triangular panel fits into the rafter rebates. Mark the position of each L-bracket. Remove the
roof and secure the L-brackets to the top of the uprights using 2 x 40mm screws per bracket. Replace the roof and
secure through the brackets into the roof panels using 2 x 40mm per bracket.
Drill
Drill
40mm
Important Note:
Front panel orientation. It is
important that the front
panel when in place has the
inset frame at the top to
allow for the seat to close
properly.
Inset top
frame
Bottom
frame flush
with cladding
End view of front panel
Important
Have the floor panel
resting in place as the
front panel is fitted.