Rowlinson Garden Products Haven Arbour User manual

Before assembly
•We recommend that time is taken to read the
instructions before starting assembly,then
follow the easy step by step guide.
The instruction sheet is only a guide to
the assembly.Certain items may not be
shown to scale.
•Check all components prior to assembly
•This product should be assembled by no
less than 2 people.
•Never attempt to erect the assembly in
high winds.
•Drill components where indicated.
Recommended tools for assembly
•Cross head screw driver
•Drill with 4mm diameter drill bit
•Tape measure
•Step ladder
x 2 Drill
No. Components Qty.
1Seat back 2
2Seat leg 2
3Left-hand seat 1
4Right-hand seat 1
5Left-hand seat facia rail 1
6Right-hand seat facia rail 1
7Left-hand upright 1
8Right-hand upright 1
9Centre post 1
10 Centre roof rafter support 1
11 Back lattice panel 2
12 Left-hand roof rafter 1
13 Right-hand roof rafter 1
14 Centre roof rafter 1
15 Roof panel 2
16 Front coverstrip 2
17 Left-hand top coverstrip 2
18 Right-hand top coverstrip 2
19 Left finial 1
20 Right finial 1
No. Fixing kit Qty.
21 40mm screws 32
22 60mm screws 20
23 70mm screws 36
24 130mm screws 5
25 150mm screws 2
12
68
5
4
7
11
10
9
13
14
15 16
32
1
17
18
Haven Arbour English SS124A
Assembly Instructions
19 20

70mm
Angled rebate
70mm
Drill
70mm 70mm
Angled end of left-hand seat Angled end of Right-hand seat
Note: Ensure that the leg
on the left-hand seat is
positioned near the front
of the seat and the leg on
the right-hand seat is
positioned near the back of
the seat.
Drill Drill
40mm
1. Back latice panels to uprights
Using 2 x 70mm screws, fix the shorter side of a back panel to the left upright, ensure that the top of the back panel is aligned with the bottom of the angled rebate of
the upright.Create a second upright and back panel section using the right-hand upright and a second back panel.
2. Seat backs to uprights
At each end of the 2 seat backs drill 2 holes in seat back frame as shown in the diagram.Position the seat back below the back panel,ensuring the seat back frame is flush
with the back of the back panel,screw through the drilled holes in the seat back frame into the upright using 2 x 70mm screws.Repeat for the other upright section.
3. Seats to uprights
Before fitting the seats to the upright sections,fit a seat leg to the angled end of each seat using 4 x 70mm screws per leg as shown below.Attach the seat fascia rails to
the front of the seats using 3 x 40mm screws per fascia.Drill holes in the seat bearers as shown below. Position the seat below the seat back, 360mm from the bottom
of the upright,screw through the seats drilled holes into the upright using 4 x 70mm screws.Attach the second seat in the same way to the other upright section.
Drill
left-hand seat Right-hand seat
Angled ends
of facias
70mm
360mm
Drill

4. Securing the centre post
Fix the centre post to 1 upright section,note orientation of drilled holes at the top of the post see diagram below.So that the seat is level make sure the post measurement
below the seat is 360mm.Secure using 2 x 70mm screws through the back panel,2 x 70mm screws through the drilled holes in the seat back frame and 2 x 70mm screws
through the seat bearer. Fit the other upright section to the centre post in the same way.
5. Centre roof rafter support
Drill 2 holes in each upright panel where indicated in the diagram below.Sit the centre support in the rebates of the 2 uprights and secure using 4 x 60mm screws,through
the drilled holes and into the centre roof rafter support. Drill 2 holes in each finial where indicated in the diagram. Fit the finials as shown using 2 x 40mm screws per
finial to the centre roof rafter support.
6. Roof rafters
Drill 2 holes in each upright panel where indicated in the diagram below.Place the roof rafters on top of the back panels make sure the roof bearers face inwards as shown
in the diagram,secure through the drilled holes of the upright into the roof rafters using 2 x 60mm screws per rafter.
DrillDrill
70mm
Seat slat bearer
Seat slat bearer
Centre post Upright
360mm
Hole orientation
DrillDrill
Drill
Roof rafter
Roof bearer
60mm 40mm 40mm
60mm
60mm

7. Centre roof rafter
Fix the centre roof support to the support block using 1 x 130mm screw as shown.Make sure that the back end of the centre roof rafter is touching the centre post and
is at the same height as the outer roof rafters.Secure the outer rafters using 4 x 130mm screws through the holes in the centre post and into the ends of the roof rafters.
Secure the centre rafter in the same way using 2 x 150mm screws.
Drill
Make sure this is at the
same height as the outer
roof rafters and touches
the centre post.
8. Roof panels
Lay the roof panels on the roof rafters and secure using 6 x 60mm screws per panel,screw through the panel and into the roof rafters as shown below.
9. Coverstrips
Drill 4 holes in each top coverstrip as shown below.Lay cover strips in place and secure with 4 x 40mm screws per strip,screw through the drilled holes of the coverstrip
into the roof panel.Fix the front coverstrips to the ends of the roof panel bearers with 3 x 40mm screws per coverstrip as shown.
Right-hand top coverstrip
Right-hand top
coverstrip
Left-hand top
coverstrip
Left-hand top
coverstrip
Drill
2006 © Rowlinson Garden Products Ltd
We constantly improve the quality of our products,
occasionally the components may differ from the
components shown and are only correct at time of
printing. We reserve the right to change the
specification of our products without prior notice.
If in doubt of any aspect regarding the assembly, use or safety of your swing seat please contact us :
Help Line (Normal Office Hours) 01829 261121
ROWLINSON GARDEN PRODUCTS LIMITED
Unit 2 Green Lane
Wardle Nr.Nantwich
Cheshire
CW5 6BN
Tel :[phone]
Fax :[phone]
130mm
130mm 130mm
150mm
60mm 60mm
40mm
40mm