Rowlinson Garden Products SS198G User manual

HD Wallstore English SS198G
No. Components Qty.
1 Floor 1
2 Left side panel 1
3 Right side panel 1
4 Back panel 2
5 Door frame Uprights (29x45x1345mm) 2
6 Door header panel 1
7 Front panel coverstrip (92x12x1365mm) 2
8 Roof panel (this part may come in 1,2 or 3 pieces) 3
9 Felt batten (29 x 35 x 1790mm) 1
10 Left-hand door 1
11 Right-hand door 1
12 Door weatherstrip (40 x 12 x 660mm) 2
13 Roofing felt (2m) 1
14 Side bargeboard (40x12x820mm) 2
15 Front bargeboard (40x12x1825mm) 1
1
2
3
12
6
9
Before assembly
•We recommend that time is taken to
read the instructions before starting
assembly, then follow the easy step by
step guide. The instruction sheet is only
a guide to the assembly.
Certain items may not be shown to scale.
•Check all components prior to assembly
•This product should be assembled
by no less than two people
•Drill all components where indicated
Recommended tools for assembly
•Powered cross head screw driver
•Hammer
•Spirit level
•Sharp knife
•Drill
•3mm drill bit
•12mm drill bit
5
4
7
11
10
13
14
15
16
No. Fixing kit Qty.
16 T-hinges 4
17 Hasp and staple 1
18 Tower bolts 2
19 Turn button 1
22 50mm screws
11
23 32mm screws 14
24 25mm screws 44
25 20mm screws 7
26 19mm roundhead screws 17
27 30mm nails 32
28 13mm felt nails 30
17
2014 © Rowlinson Garden Products Ltd
If in doubt of any aspect regarding the assembly, use or safety of your building please contact us:
Help Line (Normal Office Hours) 01829 261 121
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
18
We constantly improve the quality of our products, occasionally the
components may differ from the components shown and are only
correct at time of printing. We reserve the right to change the
specification of our products without prior notice.
19
x 2
Drill
Important information
Shiplap buildings come ready stained but this is only a preparatory treatment. To VALIDATE the guarantee, the building must be properly
treated with a recognised external wood preserver WITHIN 3 MONTHS of assembly and RE-TREATED ANNUALLY thereafter.
Adequate provision must be made to ensure ground contact is avoided and air is able to circulate underneath the building. Placing the
building on a concrete pad or slab base is acceptable provided that the building is not allowed to sit in pooled water during wet conditions.
If the building is to sit on soil or grass it MUST be erected on pressure treated wooden 50mm x 50mm or similar bearers (These are
not supplied in the kit). Rowlinson Garden Products recommend using pressure treated bearers with all buildings on any type of base.
Timber Information.
As timber is a natural material, there are certain weather conditions that may affect the materials properties. In times of excessive dry
spells the material may lose some of its internal moisture causing a certain degree of shrinkage on a panel and in periods of excessive rain
there will be a certain amount of swelling throughout the wooden panels. This process can not be avoided. If you have problems with
certain boards shrinking in dry spells try to decrease the amount of direct sunlight on the building or the amount of air passing over the
building. During hot spells spray water directly onto the panels with the aid of a garden hose.
30mm
Ensure felt batten
overhangs the front
of the wallstore
13mm
30mm
30mm
30mm
9. Bargeboards
Attach a short bargeboard to each side ensure the top and front edges are flush with the roof line and secure each board
in place using 3 x 30mm nails. Attach the long bargeboard to the front of the roof make sure it is flush to the roof line use
5 x 30mm nails as shown.
Assembly Instructions
13mm
13mm
8. Roofing felt
Lay the roofing felt on the roof with an overhang all round. Fold the felt down at the front and secure using 10 x 13mm
felt nails to the felt batten. Tension the felt over the roof and fold down at the back and secure to the back panel using
10 x 13mm felt nails. Dress down each end of the felt and secure to the side panels using 6 x 13mm felt nails per end.
Once the felt is secure trim of any excess.
7. Roof
Secure the three roof panels to the felt batten using 3 x 30mm nails per panel, ensure the roof panels are flush to the
edge of the batten. Position the roof on the assembly and secure down using 14 x 32mm screws. Screw through the roof
panel into the top frames of the side panels, back panel and front header panel.
Important Note:
Roof may come in 1,2
or 3 pieces.
*Important Note:
Roof panels may come
in 1,2 or 3 pieces.
8*
32mm
21 60mm screws 2
20 70mm screws 6

1. Floor section
Prepare a level area for the wallstore to sit and position the floor panel.
5. Doors
Lay the assembly on its back. Place the doors in the door opening, ensure they are sitting centrally. Note the inside of
the left door has the two pre-fitted block for the tower bolts. With the doors in place align the hinges to the door bracing
and secure to the door and the front panels using 7 x 25mm screws per hinge.
Tower bolt mounting
blocks on the inside of
this door.
Mark where the tower bolt
touches the floor and drill a
12mm diameter hole.
12mm
Drill
2. Wall panels
Secure the two back panels together as shown using 3 x 50mm screws. Position the back panel and the left side panel
on the floor. Note how the panel frames sit on the floor with the panel cladding overhanging the floor edge. Ensure
square and secure using 3 x 50mm screws, screw through the frame of the side panel, into the frame of the back panel.
Repeat for other side panel. Secure the door frame uprights to the framing of the side panels as shown using 3 x 70mm
screws per upright. Position the door header panel on top of the door frame uprights and secure using 1 x 50mm screw
at each end. Screw down through the lower rail of the door header panel into the ends of the uprights.
3. Securing the wall panels to the floor
Inside the assembly, secure the side panels to the floor using 1 x 60mm per side. Screw through the panel frame and floor
boards into the centre floor frame. From the outside of the assembly secure the panels to the floor using 3 x 30mm nails
per panel, nail through the panel overhang into the floor.
6. Door fittings
Secure the tower bolts to the mounting blocks using 4 x 19mm roundhead screws per bolt. With the doors shut, position
a door coverstrip so it overlaps both doors and is flush at the top of the doors, secure only to right-hand door using
3 x 20mm screws. In the same way fix the other door coverstrip flush to the bottom of the door using 3 x 20mm screws.
Fit the hasp and staple between the two coverstrips using 7 x 19mm screws as shown below. Attach the turn button to
the door header board just above the right-hand door using 1 x 20mm screw.
50mm
50mm
25mm
25mm
It is recommended to drill pilot
holes for the screws with a 3mm
drill bit before assembly.
3mm
Drill
Back panel
50mm
Side panel
Panel frames
sit on floor.
Panel cladding
overhangs floor
edge.
50mm
70mm
3mm
Drill
30mm 30mm
4. Front panel coverstrips
Secure the ends of the header panel to the side panel framing using 2 x 25mm screws at each end. Attach the front
coverstrips underneath the header panel and flush to the outer edge of the side panels. Secure using 6 x 25mm screws
per coverstrip.
25mm
25mm
19mm
19mm
20mm
20mm
Important note
To " VALIDATE" the guarantee, adequate provision must be made to ensure ground
contact is avoided and air is able to circulate underneath the building.
Placing the building on a concrete pad or slab base is acceptable provided that the
building is not allowed to sit in pooled water during wet conditions.
If the building is to sit on soil or grass it MUST be erected on pressure treated wooden
50mm x 50mm or similar bearers (These are not supplied in the kit).
Rowlinson Garden Products recommend using pressure treated bearers with all
buildings on any type of base.
It is recommended
to drill pilot holes
for the screws with
a 3mm drill bit
before assembly.
Door header
panel
60mm
3mm
Drill