Rowlinson Garden Products SS250C User manual

Before assembly
•We recommend that time is taken to
read the instructions before starting
assembly, then follow the easy step
by step guide. The instruction sheet
is only a guide to the assembly.
Certain items may not be shown to scale.
•Check all components prior to assembly
•This product should be assembled
by no less than two people.
•Never attempt to erect the assembly
in high winds.
•Drill pilot holes for each screw
Recommended tools for assembly
•Power drill/screwdriver
•Cross head screwdriver bit
•3mm drill bit
• 13mm spanner
Double Bin Store
Assembly Instructions
English SS250C
2021 © Rowlinson Garden Products Ltd
We constantly improve the quality of our products, occasionally
the components may differ from the components shown and are
only correct at time of printing. We reserve the right to change the
specification of our products without prior notice.
6. Lids
To each lid fit a lid front board using 2 x 35mm screws. Screw through the front board into the lid rails. Position the
lids between the side panels as shown. Align the predrilled bolt holes and insert a bolt. Secure each bolt with a washer
and a nut. Do not over tighten the nuts. Attach two chains to the inside of each lid using 1 x 15 mm screw per chain.
Position the chains so that they can be looped round the handles of the bin and hooked back on the chain. Attach the
lid stays using 1 x 40mm screws per stay as shown.
Important Note: To determine which roof
panel is which, look at the front edge of each
lid, the overhang of the cladding at each side
is different.
View of the front edges of the two lids
x 2 Drill
Biocidal Products Regulation EU 528/2012
Wolmanit®CX treated wood is a treated article that incorporates biocidal products: cop-
per hydroxide carbonate/II/ and boric acid. They protect wood against fungal decay /rot/
and insect attack. Keep away from food, drink and animal feeding stuffs. Avoid breathing
dust when cutting treated wood.
2
1
3
4
5
6
7
8
No. Components Qty.
1Base plates 4
2Side panel 2
3Centre panel 1
4Back panel 2
5Door 2
6Left lid 1
7Right lid 1
8Lid front board 2
9Front rail 2
10 Lid stay 2
No. Fixing kit Qty.
11 Hinges 4
12 Slide bolt 2
13 150mm bolt 1
14 100mm bolt 2
15 Nuts 3
16 Washers 3
17 Chain 4
18 60mm screws 12
19 40mm screws 16
20 35mm screws 4
21 30mm screws 36
22 15mm screws 4
9
10
11
12
Using the bin store
Position the bin inside
the store, loop the
chains around the
handles of the bin and
attach the S hook to
one of the chain links.
If in doubt of any aspect regarding the assembly, use or safety of your bin store, please contact us:
Help Line (Normal Office Hours) 01829 261 121
Email: [email protected]
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
www.rowgar.co.uk
Drill
35mm
6/7
8
Important:
Drill pilot holes in the
lid front boards for
each screw to avoid
splitting the timber.
Lid rails
Left Lid Right Lid
Large
overhang
Large
overhang
Small
overhang
7
10
6
17
17
17
17
Nut
150mm
100mm
40mm
12mm
10
100mm
Washer
Washer
Washer
Nut

4. Doors
Attach the hinges to the frames of the doors as shown below using 3x30mm screws per hinge. Position the doors
between the side panels leaving a small gap between the bottom of the door and the base plate. Secure the hinges to
the outer side panels using 3x30mm screws per hinge. For each door position the two parts of the slide bolt as shown
below and secure using 6x30mm screws for each bolt set.
Note:
Leave a small gap
between the bottom of
the door and base plate.
Note:
Attach hinges to the other side on
the second door so that the doors
open in the middle of the store.
1. Side, Centre & back panels
Secure the two side panels, centre panel and two back panels as shown below using 3 x 60mm screws for each join. Ensure
all panels are level along the bottom edge.
3. Front rails
Secure the two front rails to the top of the front face of the uprights as shown using 6x40mm screws.
View of how the base plates
are fitted to the bottom of the
three panels.
2. Base plates
Attach the four base plates using 2 x 40mm screws per plate. When attaching the plates, ensure that the end of each
plate is flush with the side panels.
60mm
60mm
2
2
3
4
4
40mm
9
9
1
1
1
1
40mm 40mm
40mm
40mm 30mm
5
11
11
30mm
30mm
12
12