Roxell Dos7 User manual

04007423 *04007423*040-2720
User Guide
EN ENGLISH
Original User Guide
Dos
7
TM

ROXELL - 040 - 2416
Dos7-USER'S GUIDE - EU
0
TABLE OF CONTENTS
TABLE OF CONTENTS
DISCLAIMER
GENERAL INFORMATION
GENERAL SAFETY RULES 1.......................................................
OPERATOR'S GUIDE 2............................................................
MAINTENANCE INSTRUCTIONS 4..................................................
TROUBLE SHOOTING GUIDE 4....................................................
DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY

ROXELL - 2313
DISCLAIMER : The original, authoritative version of this manual is the Dutch version produced by
ROXELLbvba.Subsequentchangestoanymanualmadebyanythirdpartyhavenotbeenreviewednorauthenticatedby
Roxell. Such changes may include, but are not limited to, translation into languages other than Dutch, and additions to or
deletionsfromtheoriginalcontent.Roxelldisclaimsresponsibilityforanyandalldamages,injuries,warrantyclaimsand/or
any other claims associated with such changes, inasmuch as such changes result in content that is different from the
authoritative Roxell--published Dutch version of the manual. For current product installation and operation information,
please contact the customer service and/or technical service departments of Roxell. Should you observe any questionable
contentin any manual,pleasenotifyRoxell immediately inwritingto: ROXELLbvba -- Industrielaan 13,9990 Maldegem --
Belgium.

ROXELL - 2720
1
General information
IMPORTANT: These instructions must be read, understood and all points observed by
the user, the responsible and operating personnel.
Obey the legal regulations and the applicable rules
This concerns, among other things, the European regulations and directives transposed into national legislation
and/or the laws, safety and accident prevention regulations that apply in the user's country.
During assembly, operation and maintenance of the installation the legal regulations concerned and the applic
able technical rules must be obeyed.
Intended use
The installation has been designed solely for intensive livestock use and has been developed according to the
applicable rules of good workmanship. Extra loading of the product is therefore prohibited. Any other use is
considered to be improper use. The manufacturer is not responsible for damage resulting there from. The user
bears sole responsibility.
Not-intended use
All use different than described in ” Intended use” is at the responsibility of the end user.
Liability
The (Extended) Warranty will not apply if any of the following has occurred: failure to conduct incoming goods
inspection with regards to the Products, improper handling, transportation, modification or repair; accident,
abuse or improper use; improper assembly, installation, connection or maintenance (having regard to Roxell’s
most current assembly, installation, connection and maintenance manuals); force majeure; negligence, lack of
supervision or of maintenance on the part of customer; normal wear and tear; use of cleansing agents and
disinfectants that are excluded in Roxell’s most current use and maintenance manuals; use of cleansing agents
and disinfectants in violation with the instructions received from the suppliers; or use of the Products in an
ATEXsurrounding.
The (Extended) Warranty shall not apply in the event of a defect caused either by materials or accessories
supplied by or services rendered by Customer; or by an intervention by a person or entity which is not
authorised or qualified for carrying out such intervention. Furthermore, the (Extended) Warranty will only apply
if the Products are used in livestock houses and if all parts or components of the Products are supplied by
Roxell.
Roxell will not be liable for any damages caused due to improper use, assembly, installation, connection or
maintenance of the Products. In this respect, the Customer expressly acknowledges that (i) all use, assembly,
installation, connection or maintenance must be done in accordance with Roxell’s most current assembly,
installation, connection and maintenance manuals and (ii) the electrical installation on which the Products must
be connected must be done in accordance with applicable local legislation on electrical installations.
Furthermore, the Products must be tested both mechanically and electrically in accordance with state of the art
techniques and applicable local legislation.
Personnel Qualifications
User
The person who uses a function or operation of a product for their work or who works on the product. The user
must be able to read the instructions for use and fully understand them. The user has knowledge of the func
tioning and construction of the installation.
Technically trained person
An expert who can assemble and maintain the installation (mechanically/electrically), and resolve malfunc
tions. On the basis of his/her technical training and experience, he/she has sufficient knowledge to be able to
assess activities, recognise possible dangers and rectify dangerous situations.
Storage
Put all parts to be assembled in a room or at a location where the not yet assembled components are protected
against weather influences.

ROXELL - 2720
2
Transport
Depending on the size of the parts and according to local circumstances and local legislation, the parts of the
machinehavetobetransportedwithaforklift.
The forklift must be operated by a qualified person and in accordance with the rules of good workmanship.
When lifting the load, always check if the center of gravity of the load is stable.
Dismantling
Dismantle the installation and its components in accordance with the environmental legislation of the country or
the local authorities applicable at that time. All functioning products and exchange parts must be stored and
disposed of in accordance with the applicable environmental regulations.
Environmental information for customers in the European Union
The European legislation requires that equipment marked with this symbol on the product or
packaging must not be collected with unsorted household waste. This symbol indicates that the
waste electrical and electronic equipment (WEEE) cannot be disposed of in the regular household
waste. We highly recommend that you bring your product to an official collection point so that an
expert can remove the waste electrical and electronic equipment. Inform yourself of local legisla
tion on separate collection of waste electrical and electronic equipment. Respect the local regula
tions and never dispose of the product together with household waste.
Information about waste disposal - electrical/electronic material for companies
1IntheEuropeanUnion
If you have used the product for commercial purposes and you want to dispose of it, contact Roxell who will
give you information about the return of the product. It is possible that you will have to pay a disposal charge for
the return and recycling. Small products (and small quantities) can be processed by the local collection agen
cies.
2 In other countries outside the European Union
If you want to dispose of this product, contact the local authorities for information concerning the correct dispos
al procedure.
The level of noise emission
The noise level of the installation in operation does not exceed 70dB(A).
LOTOTO = Lock Out - Tag Out - Try Out
Everyone needs his own lock and tag (label), which can’t be removed by other persons. Inform all the persons
who are influenced by the procedure.
1Toblock
•Localize all sources of energy (electric, hydraulic, pneumatic).
•Switch off.
•Take the relevant installation or the process out of operation and lock it against reuse.
You can do it by placing a padlock or other blocking mechanism (Lock Out).
2Tomark
Attach a sign, label or sticker to the padlock or blocking mechanism to reveal the nature and the expected dura
tion of the work to other persons (Tag Out).
3Tocheck
•Check if the source of energy is switched off.
•Remove any remaining energy.
•Check that the installation or process is actually safe (Try Out).

ROXELL - 2720
3
Use personal protective equipment.
Ensure you wear personal protective equipment (gloves, dust masks...).
Illuminance - Sufficient lighting
•A minimum illuminance of 200 lux is necessary during usage, maintenance and installation.
•Provide at the installation (portable) emergency lighting in case of power failure.
Electrical equipment, control panels, components and drive units
•To operate control panels, there must be at least 70 cm of free space.
•Control panels must always remain closed. The key of the control panel must be in possession of an author
ized person.
•The necessary measures must be taken by the user to keep out rats, mice and other vermin from the con-
trol panels.
•If electrical equipment, control panels, components and drive units are damaged, the system must be stopped
immediately!
•Electrical equipment, control panels, components and drive units should never be sprayed with water or oth-
er liquid!
•Electrical equipment, control panels, components and drive units should never be covered with any material.
Information about the residual risks - used safety signs
There are three levels of danger, which you can recognize from the signal word
* DANGER
* WARNING
* CAUTION
The nature and source of the imminent danger and possible consequences of not obeying warnings is stated
here!
Symbol Meaning
DANGER indicates a direct imminent danger that can result in a serious or even
fatal accident if the safety measures are not respected.
WARNING indicates a possible imminent danger that can result in a serious ac
cident or damage to the product if the safety measures are not respected.
CAUTION indicates possible, dangerous situations that can result in minor phys
ical injury or material damage if the safety measures are not respected.
This symbol refers to supporting information.
Allowed
Not allowed
This symbol will be used to draw your attention to matters that are of great
importance for your safety. It means: warning - follow the safety instruc-
tions. Disconnect the current and read the safety rules.
In short: be alert. Ignoring these instructions can cause serious injur-
ies or even death.

ROXELL - 040 - 2416 Dos7-USER'S GUIDE - EU
1
GENERAL SAFETY RULES
Carefully read the following instructions before
USING the system
Dos7 Nr. : 040...
Automatisch voedersysteem voor individueel gehuisveste zeugen
Automatic feeding system for individual sow feeding
DANGER
This SYMBOL will be used to draw your attention to matters that are
of GREAT IMPORTANCE for your SAFETY.
It means : WARNING - follow the safety instructions :
disconnect the current - re-read the safety rules.
In short : BE ALERT.IGNORING these instructions can cause
SERIOUS INJURIES or even DEATH.
IMPORTANT
1. Beforeyoudoanyrepair,ormaintenance works, always disconnect the electri-
city supply by switching off the main switch.
2. Ensure you wear personal protective equipment (gloves, dust masks).
3. With normal use the opening system starts automatically.
Never put your hands on opening tubes or cables before you have completely
switched off the electricity supply andmadesurethatnobody can switch it on
without your knowledge.
4. Never allow unauthorized persons to enter the house in your absence.
5. If the opening system stalls : immediately switch off the system. Carefully read
the trouble shooting guide and strictly follow instructions.
Contact a technically trained person.
Acableunder tension can cause very serious injuries when breaking.
6. Regularly check the cable and tube connections. Tighten if necessary.
7. Regularly check that the motor handy box is properly closed.

ROXELL - 040 - 2416
Dos7-USER'S GUIDE - EU
2
1. If a sow pen is empty or will become empty, shut off
the dispenser with the shut-off slide.
2. Do this when the dispenser is filled for the last meal
or after the last meal, before filling the dispenser
again.
3. You can disconnect the feed supply system (on the
central control panel).
4. If the dispenser is filled and there is no sow : detach
the cord of the opening pear from the opening tube
(or cable). Use a screwdriver to loosen the clamp.
OPERATOR’S GUIDE
1. You can administer solid medicines to each sow.
2. Open the window in the front panel of the dispenser.
3. Add the medicines to the feed in the dispenser.
4. Close the window again.
1. Stop the feed supply system. Switch off the central control panel.
2. Open the window after a meal.
3. Clean the inside and the outside of the dispenser (max. 25 Bar).
4. Hang the pear outside the dispenser.
5. Let the dispenser and the drop tube dry completely.
6. Close the window and restart the feed supply system.
4
5
4
5
04005211
0516
TO ADJUST THE AMOUNT OF FEED
1. First you need to calibrate the scale [liter] with your
special feed, because the scale is an indicative one
(look next page).
2. Use the white scale for pellets and the yellow scale for
mash.
3. Move the slide to the desired amount of feed.
4. Example for pellets : to feed 2 kg pellets, you set the
slide handle at 3,2 litres on the white scale.
5. You adjust the same quantity for each group.
ATTENTION ! DO NOT adjust the amount of feed unless the dispenser is
empty.
ADMINISTERING MEDICINES
TO SHUT OFF THE DISPENSERS
TO CLEAN THE DISPENSER
USING A CONTROL DISPENSER
If you use a control dispenser to stop the feed supply system, take care that there are
always sows in that compartment.

0516 04005211
ROXELL - 040 - 2416 Dos7-USER'S GUIDE - EU
3
The indication of the volume on the ROXELL dispenser for mash and pellets is an indicative scale and can differ from the usage of your specifically used feed.
For an exact feed dosage ROXELL recommends to calibrate the scale of the dosage with your specific feed before production.
1. Use a dispenser which is installed on your feeding system.
2. Choose an indicative scale on the dispenser on the feed (mash or pellets) in use.
3. Place the slide handle on the chosen scale at 1 l and fill the dispenser by the filling system.
4. Empty the dispenser and weigh the feed quantity. Note this on the calibration table (look below).
5. Repeat this procedure 5 times in total for the same volume.
6. The average of these 5 measurements reflects the real dosage of your feed at the chosen scale of the ROXELL dispenser.
7. Repeat with other volumes (1l. 7l) .
REMARK: Repeat this procedure, if you change the type of feed.
OPERATOR’S GUIDE
CALIBRATION OF THE DISPENSER
TABLE OF CALIBRATION
Measurement 1 2 3 4 5 Calibration Weight
Scale Dispenser Average
1l
2l
3l
4l
5l
6l
7l

ROXELL - 040 - 2416
Dos7-USER'S GUIDE - EU
4
MAINTENANCE INSTRUCTIONS
Switch off the main switch first.
Use personal protective equipment.
DANGER
ACTIONS IN GREY BACKGROUND MUST BE DONE BY A TECHNICALLY TRAINED PERSON.
6-monthly
1. Power unit
- Make fan dust-free X
- Check possible damages to electrical wiring X
2. Dos7
- Check possible damages X
TROUBLE SHOOTING GUIDE
Switch off the main switch first.
Use personal protective equipment.
DANGER
ACTIONS IN GREY BACKGROUND MUST BE DONE BY A TECHNICALLY TRAINED PERSON.
PROBLEM CAUSE CORRECTIVE ACTION
1. Opening system
does not
operate.
”On-off” switch not on ”I”. Adjust switch.
”Up” switch does not work. Check switch.
Thermic switching off of the motor. Orange lamp lights. Check thermic
protection. Measure phase current.
2. Opening system
keeps running
upwards.
Striking of end switches has come loose. Check end switches.
3. No feed in the
dispenser.
Shut off slide not open. Open the shut off slide.
4. No feed in the
trough.
Opening system does not operate.
Obstruction in the drop tube.
See 1.
Clean drop tube.
Dispenser not closed (dump ball not on
bottom).
Check and fix the cord to the opening
tube.

Inbouwverklaring betreffende niet voltooide machines (Richtlijn 2006/42/EG, Bijlage II.1.B)
Declaration of incorporation of partly completed machinery (Directive 2006/42/EC, Annex
II.1.B)
Fabrikant/Manufacturer:
Roxell, Industrielaan 13, 9990 Maldegem
Tel: [phone]
Fax: [phone]
Verklaart geheel onder eigen verantwoordelijkheid dat het product:
Declares on its own responsibility that the product:
Dos7 Nr: 040…
Automatisch voedersysteem voor individueel gehuisveste zeugen.
Automatic feeding system for individual sow feeding.
Waarop deze verklaring betrekking heeft, in overeenstemming is met:
-de volgende richtlijnen: 2006/42/EG (Machinerichtlijn); 2014/30/EU (Elektromagnetische
Compatibiliteit).
-de geharmoniseerde Europese Normen: EN ISO 13857; EN 349; EN ISO 12100; EN 60204-1;
EN 61439-1; EN 61439-2
Het is verboden bovengenoemd product in gebruik te stellen voordat de machine waarin het wordt
ingebouwd in overeenstemming met de bepalingen van de Machinerichtlijn is verklaard.
Tevens verbindt de fabrikant (of zijn gemachtigde) zich om op met redenen omkleed verzoek van de
nationale autoriteiten de relevante informatie over deze niet voltooide machine door te geven. De
wijze van doorgifte is digitaal. De wijze van informatieverschaffing laat de intellectueel-
eigendomsrechten van de fabrikant van de niet voltooide machine onverlet.
(NL)
Relating to this declaration, is in accordance with
-The following directives 2006/42/EC (Machinery Directive); 2014/30/EU (Electromagnetic
Compatibility).
-The harmonised European standards: EN ISO 13857; EN 349; EN ISO 12100; EN 60204-1;
EN 61439-1; EN 61439-2
This product must not be put into service until the machinery into which it is to be incorporated
has been declared in conformity with the provisions of the Machinery Directive.
The manufacturer (or its agent) also undertakes, at the duly reasoned request of the national
authorities, to provide the relevant information concerning this partly completed machinery. The
method of transmission will be digital. The manner in which the information is provided does not
prejudice the manufacturer’s intellectual property rights concerning the partly completed
machinery.
(EN)
Plaats, Datum / Place, Date: Maldegem, 01/01/2020
………………………………..
Dhr. Gino Van Landuyt
Managing Director
“This part may only be filled out if all built-in subparts are delivered by Roxell”
EG-verklaring van overeenstemming (Richtlijn 2006/42/EG, Bijlage II.1.A)
EC-declaration of conformity (Directive 2006/42/EC, Annex II.1.A)
Wij/We_________________________________________________
(naam installateur/name fitter)
_____________________________________________________________________
_____________________________________________________________________
(volledig adres en land/complete address)
Verklaren geheel onder eigen verantwoording de
Declare completely on own justification that
________________________________________________________
(naam machine/name machinery) (nummer CE-label/number CE-label)
In een installatie te hebben ingebouwd geheel volgens de Roxell-voorschriften en in
overeenstemming met de bepalingen van de Machinerichtlijn.
Has been incorporated in conformity with the provisions of the Machinery Directive and the
prescriptions of Roxell bvba.
________________________________________________________
(plaats, datum/place, date) (naam, handtekening/name, signature)
De EG-verklaring van overeenstemming / inbouwverklaring betreft uitsluitend de machine of niet
voltooide machine in de toestand waarin zij op de markt is gebracht, met uitsluiting van de later
bijvoorbeeld door de verdeler en/of installateur en/of eindgebruiker toegevoegde componenten
en/of verrichte bewerkingen.
The EC-declaration of conformity / declaration of incorporation relates exclusively to the machinery
or partly completed machine in the state in which it was placed on the market and excludes
components which are added and/or operations carried out thereafter for instance by the distributor
and/or the installer and/or the final user.
04005260
SPECIMEN


























































ROXELLbvba‐Industrielaan13,9990Maldegem(Belgium)
Tel.+3250729172‐[email protected]‐www.roxell.com

ROXELLUSAInc.‐ 720IndustrialParkRoad,AndersonMO64831(USA)
Tel.+14178456065‐[email protected]‐www.roxell.com

ROXELLMalaysia‐No.49,JalanPermata2/KS9,TamanPerindustrianAirHitam,41200Klang,Selangor(Malaysia)
Tel.+60331231767‐[e-mail]‐www.roxell.com

ROXELLРоссия‐ООО«Рокселл»ОГРН1157746055026
125167,Россия,городМосква,Ленинградскийпроспект,дом37,корпус9,помещение653
Телефон:+74959833015‐Адресэлектроннойпочты:info.russi[email protected]‐www.roxell.com