Royal Exclusiv AutoSwitch ON/OFF Manual

Operating and maintenance instructions for AutoSwitch ON/OFF
For all switchable outlets with capacitive sensor and delay release
ENG
v1.0
Royal Exclusiv pumps &skimmers
Since 1986
Klaus Jansen // Richard-Byrd-Str. 7 // 50829 Cologne // Germany
Fon +49(0)221/222886 0 // Fax [phone]
[e-mail] // www.royal-exclusiv.de

Royal Exclusiv pumps &skimmers
Since 1986
Klaus Jansen // Richard-Byrd-Str. 7 // 50829 Cologne // Germany
Fon +49(0)221/222886 0 // Fax [phone]
[e-mail] // www.royal-exclusiv.de
For more information, please visit www.royal-exclusiv.de. Simply enter the part number or name into
the search box or email: [e-mail].
All information subject to change. We try our best, but printing errors reserved.
Operating and maintenance instructions for AutoSwitch ON/OFF
For all switchable outlets with capacitive sensor and delay release
Important Notice
Please read this manual carefully before you install the device. We recommend not to proceed the installation of the
device until you read the manual. This prevents any questions and problems that might occur in installation process. As
soon as you power-on the device for the rst time, you agree that you read and understood this manual. In doubt or if
anything is unclear please contact your supplier/vendor or dealer before you start-up the device.
0.1 Foreword
The capacitive sensor of the switchable outlet recorded
contact-free electro-metals, almost all plastics, glass, ce-
ramics, wood, paper, oils, fats, water and all aqueous ma-
terials. The sensor is equipped with a NC- and C- contact,
which supplied to the socket with voltage / or which sepa-
rates from the voltage.
0.2 Packaging content
- Socket unit with relay
- Connected cable for the power plug
- Connected sensor
- Slide of sensor with plastic knurled screw to
xing of the slide
- Bar to the secure the slide and sensor on the
tank to be monitored
Bars are avaibale in3 different lengths 320, 250, 160mm
0.3 Commissioning
Please see the switchable socket with the capacitive sen-
sor from the packaging and check the product for any ship-
ping damage must appear immediately within 24 hours, at
the competent dealer.
The switchable socket with capacitive sensor is fully pre-
installed and can immediately on a lter sump, etc. to be
installed. !! Max load: 2500 Watts!! The maximum dis-
tance for the function of the senor is 8mm!
0.4 Operating and display elements
Self explanatory. The LEDs shows the status:
The green LED indicates whether there is voltage
The yellow LED shows whether the relay is working
The red LED indicates whether the sensor has tripped
The delay/relay can completely with mode Rel. on / / Rel.
off on or be turned off.
The delay can be controlled either rough (grob) or ne
(fein).
0.5 Installation with the help of the carriage
The supplied slide and bar installed as follows. Super-
glue, mirror tape or double-sided tape can be used for
xing the rail where to monitored containers.
0.6 Maintenance
The operation of the device is maintenance-free. For
proper functioning, it is worth noting:
The active surface and if necessary a freedom from de-
posits and foreign bodies are free to keep.
0.7 Setting non-contact sensor
Please note the following pages.
Bedienungsanleitung
Kapazitive Sensoren
KQ6
DE
80003301 / 00 09 / 2013

Royal Exclusiv pumps &skimmers
Since 1986
Klaus Jansen // Richard-Byrd-Str. 7 // 50829 Cologne // Germany
Fon +49(0)221/222886 0 // Fax [phone]
[e-mail] // www.royal-exclusiv.de
For more information, please visit www.royal-exclusiv.de. Simply enter the part number or name into
the search box or email: [e-mail].
All information subject to change. We try our best, but printing errors reserved.

Royal Exclusiv pumps &skimmers
Since 1986
Klaus Jansen // Richard-Byrd-Str. 7 // 50829 Cologne // Germany
Fon +49(0)221/222886 0 // Fax [phone]
[e-mail] // www.royal-exclusiv.de
For more information, please visit www.royal-exclusiv.de. Simply enter the part number or name into
the search box or email: [e-mail].
All information subject to change. We try our best, but printing errors reserved.
3
UK
1 Preliminary note
1.1 Symbols used
•Operating elements are indicated as follows:
Example: [OUT OFF] = Button “OUT OFF“�
•An instruction is indicated by “►“.
Example: ► Mount the unit as shown.
•A reaction to the action is indicated by “>“�
Example: > Yellow LED on�
Important note
Non-compliance can result in malfunctions or interference�
Information
Supplementary note�
2 Safety instructions
•Please read the product description prior to set-up of the unit� Ensure that the
product is suitable for your application without any restrictions�
•The unit conforms to the relevant regulations and EC directives�
•Improper or non-intended use may lead to malfunctions of the unit or to
unwanted effects in your application�
•That is why installation, electrical connection, set-up, operation and
maintenance of the unit must only be carried out by qualified personnel
authorised by the machine operator�
4
3 Functions and features
•capacitive sensor used as level or proximity sensor
•detects without contact metals, almost all plastics, glass, ceramics, wood,
paper, oils, greases, water and all hydrous materials and indicates their
presence by providing a switched signal
•automatic adjustment to the medium to be detected by means of programming
buttons
•in level applications the sensor detects the medium through the tank wall (only
suitable for non-metallic tanks)
3.1 Application examples

Royal Exclusiv pumps &skimmers
Since 1986
Klaus Jansen // Richard-Byrd-Str. 7 // 50829 Cologne // Germany
Fon +49(0)221/222886 0 // Fax [phone]
[e-mail] // www.royal-exclusiv.de
For more information, please visit www.royal-exclusiv.de. Simply enter the part number or name into
the search box or email: [e-mail].
All information subject to change. We try our best, but printing errors reserved.
4
3 Functions and features
•capacitive sensor used as level or proximity sensor
•detects without contact metals, almost all plastics, glass, ceramics, wood,
paper, oils, greases, water and all hydrous materials and indicates their
presence by providing a switched signal
•automatic adjustment to the medium to be detected by means of programming
buttons
•in level applications the sensor detects the medium through the tank wall (only
suitable for non-metallic tanks)
3.1 Application examples
7
UK
4.2 Use as proximity sensor
4.2.1 Installation and installation remarks
without mounting adapter with mounting adapter
2
1
33
1
2
1: sensing face
2: programming buttons
3: plastic plate
Sn: nominal sensing range (see data sheet)
A: distance = 8 mm
B: width of the mounting adapter = 36 mm
►Align the sensing face (1) to the object� Make sure that the programming but-
tons (2) remain accessible�
►Adhere to the indicated minimum distances to metallic objects opposite and
beside the sensor (free space)�
►Non-metallic objects (e�g� plastic fixtures) are allowed within the lateral free
space�
►Fix the sensor with appropriate fixing screws to the designated location�
►If the sensor is installed behind a plastic plate (3), the object will be detected
through the wall� Depending on the material used and the wall thickness the
sensor characteristics might change slightly� Do not use conductive plastics! If
possible, use thin walls�

Royal Exclusiv pumps &skimmers
Since 1986
Klaus Jansen // Richard-Byrd-Str. 7 // 50829 Cologne // Germany
Fon +49(0)221/222886 0 // Fax [phone]
[e-mail] // www.royal-exclusiv.de
For more information, please visit www.royal-exclusiv.de. Simply enter the part number or name into
the search box or email: [e-mail].
All information subject to change. We try our best, but printing errors reserved.
8
4.2.2 Minimum distances
Installation of several sensors of the same type


Sn: nominal sensing range (see data sheet)
A: sensor distance 50 mm
4.2.3 Sensor bore hole dimensions
3,2
13,4
4,3
4.3 Notes on laying of the connection cable
►Lay the cable as straight as possible and do not coil it�
►If necessary, cut the cable to the required length�
5 Electrical connection
The unit must be connected by a qualified electrician�
The national and international regulations for the installation of electrical
equipment must be adhered to�
►Disconnect power
►Connect the unit
7
UK
4.2 Use as proximity sensor
4.2.1 Installation and installation remarks
without mounting adapter with mounting adapter
2
1
33
1
2
1: sensing face
2: programming buttons
3: plastic plate
Sn: nominal sensing range (see data sheet)
A: distance = 8 mm
B: width of the mounting adapter = 36 mm
►Align the sensing face (1) to the object� Make sure that the programming but-
tons (2) remain accessible�
►Adhere to the indicated minimum distances to metallic objects opposite and
beside the sensor (free space)�
►Non-metallic objects (e�g� plastic fixtures) are allowed within the lateral free
space�
►Fix the sensor with appropriate fixing screws to the designated location�
►If the sensor is installed behind a plastic plate (3), the object will be detected
through the wall� Depending on the material used and the wall thickness the
sensor characteristics might change slightly� Do not use conductive plastics! If
possible, use thin walls�

Royal Exclusiv pumps &skimmers
Since 1986
Klaus Jansen // Richard-Byrd-Str. 7 // 50829 Cologne // Germany
Fon +49(0)221/222886 0 // Fax [phone]
[e-mail] // www.royal-exclusiv.de
For more information, please visit www.royal-exclusiv.de. Simply enter the part number or name into
the search box or email: [e-mail].
All information subject to change. We try our best, but printing errors reserved.
8
4.2.2 Minimum distances
Installation of several sensors of the same type


Sn: nominal sensing range (see data sheet)
A: sensor distance 50 mm
4.2.3 Sensor bore hole dimensions
3,2
13,4
4,3
4.3 Notes on laying of the connection cable
►Lay the cable as straight as possible and do not coil it�
►If necessary, cut the cable to the required length�
5 Electrical connection
The unit must be connected by a qualified electrician�
The national and international regulations for the installation of electrical
equipment must be adhered to�
►Disconnect power
►Connect the unit
9
UK
5.1 Wiring
p-switching (type ���FPKG��� or ���FPOG���)







 





n-switching (type ���FNKG��� or ���FNOG���)












BN = brown, BK = black, BU = blue
BN = OUT / IO-Link 4: OUT / IO-Link
5.2 Unit versions with auto-detect
On power up, unit types with auto-detect (types ���FAKG or ���FAOG���) detect
automatically if the output is connected to L- (p switching) or to L+ (n switching)�
►Disconnect the unit to acknowledge a change of the load connection�
Automatic load detection is only ensured when a resistor is switched in
series to a closed mechanical contact�
load detection is possible load detection impossible











Royal Exclusiv pumps &skimmers
Since 1986
Klaus Jansen // Richard-Byrd-Str. 7 // 50829 Cologne // Germany
Fon +49(0)221/222886 0 // Fax [phone]
[e-mail] // www.royal-exclusiv.de
For more information, please visit www.royal-exclusiv.de. Simply enter the part number or name into
the search box or email: [e-mail].
All information subject to change. We try our best, but printing errors reserved.
10
6 Operating and display elements
12 3
1: sensing face
2: programming buttons
3: LED
7 Settings
7.1 Basic teach empty state
Using the basic teach empty state the unit suppresses the installation environ-
ment� The basic teach empty state resets the unit, an adjustment teach already
carried out is deleted�
►Empty the tank until the level is at least 20 mm
below the sensor�

Set the unit as normally open (output closes when the
tank is full):
►Press [OUT OFF] for min� 2 s (max� 6 s)�
> While pressing the pushbutton the LED flashes
slowly� After releasing the pushbutton, the LED
goes out� 2 - 6 s
Set the unit as normally closed (output opens when
the tank is full):
►Press [OUT ON] for min� 2 s (max� 6 s)�
> While pressing the pushbutton the LED flashes
slowly� After releasing the pushbutton, the LED
lights continuously� 2 - 6 s
The unit is now ready for operation� For the detection of media with a low dielectric
constant (e�g� plastic granulates or oils) no further setting is required�
9
UK
5.1 Wiring
p-switching (type ���FPKG��� or ���FPOG���)













n-switching (type ���FNKG��� or ���FNOG���)












BN = brown, BK = black, BU = blue
BN = OUT / IO-Link 4: OUT / IO-Link
5.2 Unit versions with auto-detect
On power up, unit types with auto-detect (types ���FAKG or ���FAOG���) detect
automatically if the output is connected to L- (p switching) or to L+ (n switching)�
►Disconnect the unit to acknowledge a change of the load connection�
Automatic load detection is only ensured when a resistor is switched in
series to a closed mechanical contact�
load detection is possible load detection impossible











Royal Exclusiv pumps &skimmers
Since 1986
Klaus Jansen // Richard-Byrd-Str. 7 // 50829 Cologne // Germany
Fon +49(0)221/222886 0 // Fax [phone]
[e-mail] // www.royal-exclusiv.de
For more information, please visit www.royal-exclusiv.de. Simply enter the part number or name into
the search box or email: [e-mail].
All information subject to change. We try our best, but printing errors reserved.
10
6 Operating and display elements
12 3
1: sensing face
2: programming buttons
3: LED
7 Settings
7.1 Basic teach empty state
Using the basic teach empty state the unit suppresses the installation environ-
ment� The basic teach empty state resets the unit, an adjustment teach already
carried out is deleted�
►Empty the tank until the level is at least 20 mm
below the sensor�

Set the unit as normally open (output closes when the
tank is full):
►Press [OUT OFF] for min� 2 s (max� 6 s)�
> While pressing the pushbutton the LED flashes
slowly� After releasing the pushbutton, the LED
goes out� 2 - 6 s
Set the unit as normally closed (output opens when
the tank is full):
►Press [OUT ON] for min� 2 s (max� 6 s)�
> While pressing the pushbutton the LED flashes
slowly� After releasing the pushbutton, the LED
lights continuously� 2 - 6 s
The unit is now ready for operation� For the detection of media with a low dielectric
constant (e�g� plastic granulates or oils) no further setting is required�
11
UK
7.2 Adjustment teach full state
Necessary for aqueous media� The sensitivity of the unit is optimised� Later on,
the adjustment teach full state can be repeated at any time, an adjustment teach
empty state already carried out is not affected�
A basic teach empty state must be carried out prior to the adjustment teach full
state (→ 7.1 Basic teach empty state)! If it is not possible to empty the tank, a
basic teach empty state can be carried out by simulating the empty state (e�g�
adjustment when not installed, adjustment at a higher position)� For optimum
function it is necessary to carry out the “modified basic teach empty state“ →
7�3 Modified basic teach empty state) when the tank is emptied the next time�
►Fill the tank until the sensing face of the unit is
covered�
> For NO the LED lights, for NC it goes out�
Set the unit as normally open (output closes when the
tank is full):
►Press [OUT ON] for min� 6 s�
> While pressing the pushbutton the LED first flashes
slowly, after 6 s more quickly� After releasing the
pushbutton, the LED lights continuously� > 6 s
Set the unit as normally closed (output opens when
the tank is full):
►Press [OUT OFF] for min� 6 s�
> While pressing the pushbutton the LED first flashes
slowly, after 6 s more quickly� After releasing the
pushbutton, the LED goes out� > 6 s
7.3 Modified basic teach empty state
Recommended for deposits in the tank� Deposits are largely suppressed� This is
also recommended if it has not been possible to carry out a basic teach empty
state (e�g� if the sensor is set up on a full tank; details: → 7.2 Adjustment teach full
state)

Royal Exclusiv pumps &skimmers
Since 1986
Klaus Jansen // Richard-Byrd-Str. 7 // 50829 Cologne // Germany
Fon +49(0)221/222886 0 // Fax [phone]
[e-mail] // www.royal-exclusiv.de
For more information, please visit www.royal-exclusiv.de. Simply enter the part number or name into
the search box or email: [e-mail].
All information subject to change. We try our best, but printing errors reserved.
12
Later on, the modified basic teach empty state can be repeated at any time, an
adjustment teach full state already carried out is not affected�
►Empty the tank until the level is below the sensing
face of the unit�
> For NO the LED goes out, for NC the LED lights�
Set the unit as normally open (output closes when the
tank is full):
►Press [OUT OFF] for min� 6 s�
> While pressing the pushbutton the LED first flashes
slowly, after 6 s more quickly� After releasing the
pushbutton, the LED goes out� > 6 s
Set the unit as normally closed (output opens when
the tank is full):
►Press [OUT ON] for min� 6 s�
> While pressing the pushbutton the LED first flashes
slowly, after 6 s more quickly� After releasing the
pushbutton, the LED lights continuously� > 6 s
7.4 Locking / unlocking
The unit can be electronically locked to protect it against unintentional setting�
►To lock press [OUT ON] and [OUT OFF]simulta-
neously for 10 s�
> Acknowledgement: LED state (yellow) changes for
a short time (the lit LED goes out briefly or the LED
which is not lit lights briefly)�
►To unlock repeat this step� 10 s
If the unit does not react, it may be locked�
11
UK
7.2 Adjustment teach full state
Necessary for aqueous media� The sensitivity of the unit is optimised� Later on,
the adjustment teach full state can be repeated at any time, an adjustment teach
empty state already carried out is not affected�
A basic teach empty state must be carried out prior to the adjustment teach full
state (→ 7.1 Basic teach empty state)! If it is not possible to empty the tank, a
basic teach empty state can be carried out by simulating the empty state (e�g�
adjustment when not installed, adjustment at a higher position)� For optimum
function it is necessary to carry out the “modified basic teach empty state“ →
7�3 Modified basic teach empty state) when the tank is emptied the next time�
►Fill the tank until the sensing face of the unit is
covered�
> For NO the LED lights, for NC it goes out�
Set the unit as normally open (output closes when the
tank is full):
►Press [OUT ON] for min� 6 s�
> While pressing the pushbutton the LED first flashes
slowly, after 6 s more quickly� After releasing the
pushbutton, the LED lights continuously� > 6 s
Set the unit as normally closed (output opens when
the tank is full):
►Press [OUT OFF] for min� 6 s�
> While pressing the pushbutton the LED first flashes
slowly, after 6 s more quickly� After releasing the
pushbutton, the LED goes out� > 6 s
7.3 Modified basic teach empty state
Recommended for deposits in the tank� Deposits are largely suppressed� This is
also recommended if it has not been possible to carry out a basic teach empty
state (e�g� if the sensor is set up on a full tank; details: → 7.2 Adjustment teach full
state)