Royal Line Onedrous Digital Bidet TH-0111 User manual

Onedrous Digital Bidet by Royal Line
TH-0111 Toilet bowl installation
- This user manual contains the products warranty. Please submit to our warranty department within 15 days of purchase.
“Important safeguards/general cautions”- information that can protect user from safety hazards.
Please read carefully for proper usage.

This product should be installed using the included t-valve
Toilet space requirements:
Minus slot Handle Screw inlet valve
■General inlet valve
(angle valve)
■Screw inlet valve
(angle valve)
■For special plumbing,
you may need a licensed plumber.
- Important Note: All settings have been preset by factory
- This product must plug into a 120V grounded GFCI outlet. (North America standard 120V)
- Do not plug into outlet before installation is complete
- All electrical work must be performed by a licensed electrician
Contents can be found in box 2 of 2.
Attention before installation
Must use fixed angle valve, and not elbow
shaped handle as per the below picture
Fixed angle valve Flange components
2.5"
10"
12"
Check water supply valve in bathroom
Installation method
INCLUDED PARTS ( IN THE BOX OF CHINAWARE )
angle valve
drain hole
nut, washer, T volt
flange packing, flange
Installation Manual and Operating Instructions
2 3
Toilet bowl installation & caution
Installation
21
Before Installation
1) Distance between finished wall and the center of the floor drain must be 12" (305mm)
2) Water supply should be approximately 10"(250mm) to the left (facing the bowl) from the center line of the flange and
approximately 2-1/2"(60mm) above the finished floor.
3) Using the provided template, confirm the installation dimensions of the Rough-in and the mounting blocks.
2.5"
10"
7.5"
12"
16"
Check to make sure you have all these parts from the package
* 12" Pipe Wrench * Screwdriver * 10" Adjustable wrench
* Putty knife * Carpenter's level * Drill
* Tape Measure * Pliers
FLANGE
PART
2 X NUT 2 X WASHER 2 X T-BOLT 1 X PACKING 1 X FLANGE
MOUNTING
BLOCK
PART
2 X CAPS 2 X SCREWS 2 X BUSHINGS 2 X WASHERS 2 X LAGBOLTS 2 X LAGBOLT
ANCHORS
2 X MOUNTING
BLOCKS
OTHERS
1 x WATER
SUPPLY VALVE
COMMON TOOLS NEEDED

- Please check the position and distance for
installation with ruler
- Check the position for concrete anchor and drill
a hole with electric drill.
check the place for installation Install the concrete anchor
- Put the concrete anchor into hole with hammer.
Install concrete anchor Put hanger on the hole and fix it with bolts
- Place the toilet bowl
Fix the toilet bowl
Ruler
Drill
Fix the toilet bowl like below picture.
Installation Manual and Operating Instructions
4 5
5
Toilet bowl installation & caution
Installation
12
14
11
109
13
Hole
Hole
Block
Driver
Hole Hanger
Cap Bolt
Boltguide
Washer
water inlet hose
T-valve
water supply valve
2.5"
10"
7.5"
12"
16"
- Insert flange packing to flange - Insert bolt to flange
(note the direction of the bolt)
Flange packing + flange Flange + bolt
- Insert flange to toilet bowl - Assemble flange to toilet bowl by using nut and
washer
Flange + Toilet bowl Flange + Toilet bowl nut
- Please handle carefully, as this may require more than
one person
Insert to drain hole
flange packing
flange
T bolt
washer
nut
drain hole
When fixing hanger, fix it as picture below.
43
65
87

Installation Manual and Operating Instructions
6 7
Toilet bowl installation & caution
Installation
Adjustment by user (any adjustments by the user is not recommended)
Water quantity is adjusted with the sequence shown in
the figure. (When floating ball is raised, water usage is
increased, and when it is lowered, water usage is
decreased) Unit is set at factory at appropriate water
level. Adjusting the factory settings are not
recommended and will affect operation of the unit.
Adjust the length of ball chain by examining the
functioning state of plug.