Royal Vendors RVV NG Reference manual

SUBJECT: Installation of the RVV Card Reader Adapter Kit
MODELS: RVV NG
KIT NUMBER KIT DESCRIPTION
355102 RVV Card Reader Adapter Kit - Dasani
355103 RVV Card Reader Adapter Kit - Coca-Cola
355105 RVV Card Reader Adapter Kit - Wellness
355106 RVV Card Reader Adapter Kit - Pepsi
TOOLS REQUIRED: 11/32" (9 mm) socket or nut driver
ESTIMATED INSTALLATION TIME: <15 minutes
ANY QUESTIONS? CONTACT ROYAL VENDORS’ CUSTOMER SERVICE DEPARTMENT
IN NORTH AMERICA, CALL TOLL FREE 1 800 931 9214
F0019003.FRM REV.: C
ISSUE DATE: 05 JUN 1995 REV. DATE: 05 DEC 2003
REASON FOR BULLETIN: Beginning in
September 2007 (Coca-Cola equipment) and
November 2007 (all other brands), all new RVV models
are designed to accomodate a separate bill validator and card reader. This bulletin describes the
procedure for installing the RVV Card Reader Adapter Kit, which allows for the installation of both a bill
validator and a card reader.
INSTALLATION INSTRUCTIONS:
1. Remove power by unplugging the vender's power cord from the AC voltage source (wall outlet).
2. Remove the existing select panel decal or fascia from the vender. (Refer to Figure 1.)
3. Unplug the harnessing to the bill validator. Then, using an 11/32" (9 mm) socket or nut driver,
remove the four nuts that secure the bill validator. (Refer to Figure 2.) Once these are removed,
pull the validator straight out of the door.
4. Remove the four nuts that secure the validator filler plate in the vender's door. (Refer to Figure 2.)
Remove the filler plate.
5. Mount the validator adapter plate (from the kit). Secure it with the four nuts that were removed in
Step 4. (Refer to Figure 3.)
6. Affix the select panel decal (from the kit) to the front of the vender's door in place of the decal that
was removed in Step 2.
7. Mount the card reader where the bill validator was previously mounted (lower hole). Secure it with
the four nuts that were removed in Step 3.
8. Mount the bill validator onto the validator adapter plate. Secure it with the four nuts from the kit.
9. Connect all harnessing to the validator and to the card reader as required.
10.Restore power to the vender by plugging the vender's power cord into the AC voltage source (wall
outlet).
R
Page: 1 of 2
Date: 17 Sept 09
Revision: 02
Number of
People
Required
In an effort to provide our customers with the latest information on our equipment, Royal Vendors sends service bulletins to customers using the original ship-to
address or e-mail addresses, if supplied by our customers. We also post all service bulletins on our website at www.royalvendors.com. If for any reason a
vender is moved to another location or is sold to another customer other than to whom Royal Vendors originally sent the machine, it is the responsibility of the
original purchaser of the vender to notify the appropriate personnel of the service bulletin.
287
426 Industrial Boulevard • Kearneysville WV 25430-2776 • USA
Telephone: [phone] • [email protected]
Toll-free in North America: 1 800 931 9214 • Fax: [phone]
Canada: [phone] • Mexico: [phone]
Europe: [phone] • Australia: [phone]
SERVICE BULLETIN
The following areas of this vender contain voltage which
can cause serious injury or even death: the main power
cord, supplying 115-230 VAC to the evaporator, EMI filter,
and refrigeration system; the power line from the EMI filter
to the ballast and transformer; and the ballast, which can
produce upwards of 600 volts. Remove power from vender
before working in any of these areas.

ANY QUESTIONS? CONTACT ROYAL VENDORS’ CUSTOMER SERVICE DEPARTMENT
IN NORTH AMERICA, CALL TOLL FREE 1 800 931 9214
F0019003.FRM REV.: C
ISSUE DATE: 05 JUNE 1995 REV. DATE: 05 DEC 2003
R
SUBJECT: Installation of the RVV Card Reader Adapter Kit
MODELS: RVV NG
Page: 2 of 2
Date: 17 Sept 09
Revision: 02
Figure 1.
Select panel decal or fascia
Remove the existing select panel decal
or fascia from the vender located in the
upper right corner area.
Figure 2.
Remove the four nuts that secure the
validator (two on each side).
Validator ller plate nut (4 nuts total)
Figure 3.
Validator adapter plate
11/32” nut
(9 mm)
Mount the validator adapter plate, as shown, and
secure it with the four 11/32" (9 mm) nuts.
Note: Some parts are removed in this illustration
for clarity.
287
426 Industrial Boulevard • Kearneysville WV 25430-2776 • USA
Telephone: [phone] • [email protected]
Toll-free in North America: 1 800 931 9214 • Fax: [phone]
Canada: [phone] • Mexico: [phone]
Europe: [phone] • Australia: [phone]
SERVICE BULLETIN