RTX RTX8200 User manual

RTX8200 LOCATION GATEWAY GUIDE 4.6 1 |P a g e
Proprietary and Confidential
RTX8200
Location Gateway
Technical Reference Document
Version 1.0
© May-2018 RTX A/S, Denmark

RTX8200 LOCATION GATEWAY GUIDE 4.6 2 |P a g e
Proprietary and Confidential
Trademarks
RTX and the combinations of its logo thereof are trademarks of RTX A/S, Denmark.
Other product names used in this publication are for identification purposes and maybe the trademarks of their
respective companies.
Disclaimer
The contents of this document are provided about RTX products. RTX makes no representations with respect to
completeness or accuracy of the contents of this publication and reserves the right to make changes to product
descriptions, usage, etc., at any time without notice. No license, whether express, implied, to any intellectual property
rights are granted by this publication
Confidentiality
This document should be regarded as confidential, unauthorized copying is not allowed
© Sep-2018 RTX A/S, Denmark, All rights reserved
http://www.rtx.dk

RTX8200 LOCATION GATEWAY GUIDE 4.6 3 |P a g e
Proprietary and Confidential
INDEX

RTX8200 LOCATION GATEWAY GUIDE 4.6 4 |P a g e
Proprietary and Confidential
1About This Document
This document describes the configuration, customization, management, operation, maintenance and troubleshooting
of the RTX8200 Location Gateway in RTX generic mode. For customer, specific modes refer to specific customer
agreements, which describe the software operational deviations from this document.
1.1 Audience
Who should read this guide? First, this guide is intended for networking professionals responsible for designing and
implementing RTX based enterprise networks.
Second, network administrators and IT support personnel that need to install, configure, maintain, and monitor
elements in a “live” SME VoIP network will find this document helpful. Furthermore, anyone who wishes to gain
knowledge on fundamental features in the Beatus system can also benefit from this material.
1.2 When Should I Read This Guide
Read this guide before you install the core network devices of VoIP SME System and when you are ready to setup or
configure SIP server, NAT aware router, advanced VLAN settings, base stations, and Location Gateway’s in a multi cell
setup.
This manual will enable you to set up and connect your RTX8200 Location Gateway in a Multi Cell system.
1.3 Important Assumptions
This document was written with the following assumptions in mind:
•You understand network deployment in general
•You have working knowledge of basic TCP/IP/SIP protocols, Network Address Translation, etc...
•A proper site survey has been performed, and the administrator have access to these plans
1.4 What’s Inside This Guide
We summarize the contents of this document in the table below:
WHERE IS IT?
CONTENT
PURPOSE
CHAPTER 2
TBD
TBD
CHAPTER 3
TBD
TBD
CHAPTER 4
TBD
TBD
CHAPTER 5
TBD
TBD

RTX8200 LOCATION GATEWAY GUIDE 4.6 5 |P a g e
Proprietary and Confidential
1.5 What’s Not in This guide
This guide provides overview on, how-to configure RTX8200 Location Gateway to an RTX Generic System.
It is not intended as a comprehensive reference to all detail and specific steps on how to configure other vendor
specific components/devices needed to make the SME VoIP System functional. For such a reference to vendor
specific devices, please contact the respective vendor for documentation.
Configuration on specific Alarm/Messaging servers are not included in this guide.
1.6 Abbreviations
For this document, the following abbreviations hold:
DHCP: Dynamic Host Configuration Protocol
DNS: Domain Name Server
HTTP(S): Hyper Text Transfer Protocol (Secure)
(T)FTP: (Trivial) File Transfer Protocol
IOS: Internetworking Operating System
PCMA: A-law Pulse Code Modulation
PCMU: mu-law Pulse Code Modulation
PoE: Power over Ethernet
RTP: Real-time Transport Protocol
RPORT: Response Port (Refer to RFC3581 for details)
SIP: Session Initiation Protocol
SME: Small and Medium scale Enterprise
VLAN: Virtual Local Access Network
TOS: Type of Service (policy based routing)
URL: Uniform Resource Locator
UA: User Agent
1.7 References/Related Documentation
RTX8430 Handset_Manual_Operations_v4.6
RTX8630 Handset_Manual_Operations_v4.6
RTX8631_Handset_Manual_Operations_v4.6
RTX8632_Handset_Manual_Operations_v4.6
RTX8633_Handset_Manual_Operations_v4.6
RTX8830_Handset_Manual_Operations_v4.6
How to Deploy SME VOIP System v1.4
Provisioning of SME VoIP System (23)
1.8 Document History
REVISION
AUTHOR
ISSUE DATE
COMMENTS
4.6
HDJ
01-04-2019
Updated to V460 Firmware

RTX8200 LOCATION GATEWAY GUIDE 4.6 6 |P a g e
Proprietary and Confidential
1.9 What is new
What new features have been added.
VERSION
FEATURE
V460
All new product
1.10 Documentation Feedback
We always strive to produce the best and we also value your comments and suggestions about our documentation. If
you have any comments about this guide, please enter them through the Feedback link on the RTX website. We will
use your feedback to improve the documentation.

RTX8200 LOCATION GATEWAY GUIDE 4.6 7 |P a g e
Proprietary and Confidential
2. Introduction –System overview
In a typical DECT telephony system, you have base station, repeaters and handsets, allowing the users to
make/receive calls and messages.
A typical setup could look like this:
Increasing demand for locating equipment, personal or pushing information to specific handset on a specific location,
demands the system to know exactly where the device is located.
This can be done be adding RTX8200 Location gateway devices to the DECT system.

RTX8200 LOCATION GATEWAY GUIDE 4.6 8 |P a g e
Proprietary and Confidential
Wireless Bands
The bands supported in the SME VoIP are summarized as follows:
Frequency bands:
1880 –1930 MHz (DECT)
1880 –1900 MHz (10 carriers) Europe/ETSI
1910 –1930 MHz (10 carriers) LATAM
1920 –1930 MHz (5 carriers) US
System Capacity (in Summary)
SME network capacity of relevant components can be summarized as follows:
DESCRIPTION
CAPACITY
MAX BASE STATION
4.000
MAX LOCATION GATEWAYS
16.000
MAX TERMINALS (SELECT BETWEEN 6 HANDSETS AND 1 HEADSET MODELS
16.000
MAX ACTIVE CALLS (NARROW BAND)
32.000
MAX ACTIVE CALLS (WIDE BAND)
16.000

RTX8200 LOCATION GATEWAY GUIDE 4.6 9 |P a g e
Proprietary and Confidential
Installation of Location Gateways
After planning the network, installing the base stations, the Locations gateways must be added, therefore, we briefly
describe how to install the location gateways. One important thing that must be decided before installing the location
gateways is how to power them.
Package –Contents/Damage Inspection
Before Package Is Opened:
Examine the shipping package for evidence of physical damage or mishandling prior to opening. If there is a proof of
mishandling prior to opening, you must report it to the relevant support center of the regional representative or
operator.
Contents of Package:
Make sure all relevant components are available in the package before proceeding to the next step.
Every shipped base unit package/box contains the following items:
•Location Gateway
Please only use screws and actors with the following dimensions.
Screws: 30,7 mm (L), 2,6 mm (W)
Actors: 24,8 mm (L), 5,8 mm (W)
Damage Inspection:
The following are the recommended procedure for you to use for inspection:
1. Examine all relevant components for damage.
2. Make a “defective on arrival –DOA” report or RMA to the operator. Do not move the shipping carton until
the operator has examined it. If possible, send pictures of the damage. The operator/regional representative
will initiate the necessary procedure to process this RMA. They will guide the network administrator on how
to return the damaged package if necessary.
3. If no damage is found, then unwrap all the components and dispose of empty package/carton(s) in
accordance with country specific environmental regulations.

RTX8200 LOCATION GATEWAY GUIDE 4.6 10 |P a g e
Proprietary and Confidential
RTX8200 Location Gateway Mechanics
The Location Gateway front
How to insert batteries or PoE module
To open the Location gateway, you need to use a screwdriver or other flat tool.
Insert the screwdriver on the left side and press the small metal lock to open the Location gateway.
Now insert the batteries (2xAA) or the PoE module.
If using PoE module remember to remove the small piece of plastic covering the Ethernet plug.
RTX8200 Location Gateway –Tamper Alarm
The RTX8200 Location Gateway is equipped with a tamper alarm, in case someone tries to tamper with the device.
The tamper alarm allows the system admin to receive a warning if tampering is detected. Tampering alarm is activated
if the front is removed.
Vendor Logo