Rush Creek Creations 37-0046 User manual

Item # 37-0046
9-GUN, 12 PISTOL CABINET WITH STORAGE

Tools Needed For Assembly:
Screwdriver
Drill
Assembly Tips:
If you are using an electric screwdriver for assembly, set it at low torque and do not over-tighten the hardware.
Care:
Apply lemon oil with a soft cotton cloth. Do not use products with silicone; these may cause damage to the finish. Do not
allow the wood to come in contact with any type of paint remover.
Changes in temperature and humidity may cause the wood to dry out, which can cause the bolts to loosen. Check the
bolts periodically to make sure they are still tight. DO NOT put your wood rack directly against hot radiators or other
sources of heat. This may cause the wood to dry and crack.
CONNECTIONS:
Safety Recommendations:
Keep the gun cabinet locked at all times for safety.
Store gun cabinet keys in a secure place that is out of reach for children.
Additional anchoring to the floor through the bottom of the cabinet is recommended.
1
If you have any problems with your new product,
DO NOT RETURN IT TO THE STORE!
Please contact us at 1-866-815-4173,
or e-mail us at [email protected]

Parts List
Side panel
Side panel for
bottom cabinet
Butt plates panel
Bottom panel
Barrel rest
Back panel
Top panel
Front door
panel
Door knob
Flat
head
screw
Bolt
Back panel
support
Cap
2
Drawer
Top panel for
bottom cabinet
Pistol cabinet
Pistol rest
47 20
Flat
head
screw
Flat
head
screw
Flat
head
screw
Anchor

Step 1:
Unpack the carton on a smooth surface. Check carefully to
ensure that all parts are included.
Attach the side panels (#1) to the top panel for
the bottom cabinet (#3) using bolts (#13).
Connect the bottom cabinet side panel
(#2) to the top panel for the
bottom cabinet (#3). Attach
the assembled piece to
the bottom panel
(#4) with bolts
(#13).
3
Step 2:
Place the pistol cabinet (#5) in the middle of the gun cabinet. Attach the barrel rest (#6) to the side
panels using bolts (#13).

Step 3:
Insert the butt plate panel (#7).
4
Step 4:
Slide and push the back panel (#8) between the two side panels.

5
Step 5:
Use bolts (#13) to tighten the top panel (#9).
18
Step 6:
At least two people are needed to
carefully lift the cabinet to an upright
position. Use flat head screws (#18)
to screw the back panel support
(#16) to the back panel. Use flat head
screws (#15) to screw the back panel
to the cabinet.

Step 8:
The gun cabinet is fully assembled.
6
19
21
20
Step 7:
Install the front door panel (#10) to the cabinet; tighten bolts (#13) into the holes on the door
panel. Insert the pistol rest (#14) into the pistol cabinet; insert the drawer (#12) into the
bottom section.
Use flat head screws (#19) to screw the door knob (#11) to the door.
Use flat head screws (#20) with anchors (#21) to secure the cabinet to the wall.
Fill the predrilled holes with a cap (#17) when the assembly is complete.

Rush Creek
Aurora, IL 60504
www.rushcreeklogfurniture.com
1-866-815-4173
Rush Creek is a trademark owned by Triumph Sports USA
©2008 Triumph Sports USA. All Rights Reserved.
Warranty:
All of our products come with a one year warranty on all parts.
Manufacturer Defects:
Defective parts will be replaced at no cost to you. Please send an e-mail to [email protected] including photos of the
defective part(s) and we will send replacements. PLEASE NOTE: Cracks in logs are not defects. They may develop during the log drying
process and do not affect the stability of the piece in any way, and add to the rustic appeal of your log furniture.
If your product needs service, please be advised that Rush Creek reserves the right to decline service when the product is found to be
excessively worn, altered in any way, or when damage is caused by acts other than defective workmanship or materials. This warranty
is void if the product has been subject to abuse. For service under this warranty, please contact Rush Creek. Please provide your receipt
as proof of purchase.
Be sure to check out all the exciting products
has to offer. Visit our web site at:
www.rushcreeklogfurniture.com