Russell Hobbs RHCM3 Installation guide

INSTRUCTIONS AND WARRANTY
RHCM3
Russell Hobbs 5 in 1 coffee maker

2
Congratulations on purchasing our Russell Hobbs 5 in 1 coffee maker. Each unit is
manufactured to ensure safety and reliability. Before using this appliance for the first
time, please read the instruction manual carefully and keep it for future reference.
FEATURES OF THE RUSSELL HOBBS 5-IN-1 COFFEE MAKER
5 in 1 coffee maker (filter coffee, espresso, latte, mocha and cappuccino)
1.5 litre water tank
15 bar pressure pump
10 cup filter capacity
4 cup espresso capacity
Permanent filter
Steam nozzle for frothing milk
2 independent thermostats
Warming plate for keeping coffee warm for longer
IMPORTANT SAFEGUARDS
When using any electrical appliance, basic safety precautions should always be followed
including the following:
1. Please read the instructions carefully before using any appliance.
2. Always ensure that the voltage on the rating label corresponds to the mains
voltage in your home.
3. Incorrect operation and improper use can damage the appliance and cause injury
to the user.
4. The appliance is intended for household use only. Commercial use invalids the
warranty and the supplier can not be held responsible for injury or damage
caused when using the appliance for any other purpose than that intended.
5. Avoid any contact with moving parts.
6. This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
7. Children should be supervised to ensure that they do not play with the appliance.
8. Check the power cord and plug regularly for any damage. If the cord or the plug
is damaged, it must be replaced by the manufacturer or a qualified person in
order to avoid an electrical hazard.

3
9. Do not use the appliance if it has been dropped or damaged in any way. In case
of damage, take the unit in for examination and/or repair by an authorised service
agent.
10. To reduce the risk of electric shock, do not immerse or expose the motor
assembly, plug or the power cord to water or any other liquid.
11. Never immerse the unit in water or any other liquid for cleaning purposes.
12. Remove the plug from the socket by gripping the plug. Do not pull on the cord to
disconnect the appliance from the mains. Always unplug the unit when not in
use, before cleaning or when adding or removing parts.
13. The use of accessory attachments that are not recommended or supplied by the
manufacturer may result in injuries, fire or electric shock.
14. A short cord is provided to reduce the hazards resulting from becoming
entangled in or tripping over a longer cord.
15. Do not let the cord hang over the edge of a table or counter. Ensure that the cord
is not in a position where it can be pulled on inadvertently.
16. Do not allow the cord to touch hot surfaces and do not place on or near a hot gas
or electric burner or in a heated oven.
17. Do not use the appliance on a gas or electric cooking top or over or near an open
flame.
18. Use of an extension cord with this appliance is not recommended. However, if it
is necessary to use an extension lead, ensure that the lead is suited to the power
consumption of the appliance to avoid overheating of the extension cord,
appliance or plug point. Do not place the extension cord in a position where it can
be pulled on by children or animals or tripped over.
19. This appliance is not suitable for outdoor use. Do not use this appliance for
anything other than its intended use.
20. DO NOT carry the appliance by the power cord.
21. Do not leave this appliance unattended during use. Always unplug the unit when
not in use or before cleaning.
22. Always operate the appliance on a smooth, even, stable surface. Do not place
the unit on a hot surface.
23. Ensure that the switch is in the “Off” position after each use.

4
24. The manufacturer does not accept responsibility for any damage or injury caused
by improper or incorrect use, or for repairs carried out by unauthorised
personnel.
25. In case of technical problems, switch off the machine and do not attempt to repair
it yourself. Return the appliance to an authorised service facility for examination,
adjustment or repair. Always insist on the use of original spare parts. Failure to
comply with the above mentioned pre-cautions and instructions, could affect the
safe operation of this machine.
ADDITIONAL SAFEGUARDS
PARTS DIAGRAM
A. water tank cover B. water tank C. warming jug facility
D. nylon filter E. removable brew basket F. drip carafe
G. removable shelf H. drip tray I. measuring spoon and
tamper
J. Metal funnel (for Espresso)
K. press bar（press steel filter with it when pour coffee residue to avoid its slipping
out）
L. Espresso jug M. steel mesh N. adjustable steam outlet
O. steam wand P. Control panel (See Fig.1) Q. Transition knob

5
OPERATING INSTRUCTIONS
BEFORE FIRST USE:
Please rinse the coffee maker with warm water as follows:
Pour the water into the water tank according to the gauge, then replace its cover.
Set nylon filter in removable brew basket (add NO coffee ground), then fix
removable brew basket in the coffee maker.
Set steel mesh into the metal funnel (no coffee in the metal filter mesh) then
place them upwards into the snap and you can fix them into coffee maker firmly,
turn it anticlockwise until it is at the lock position.
Place drip carafe on keeping warm plate and espresso jug or the coffee jug on
removable shelf.
CAUTION: there is a tube outlet under the removable shelf, this is the
overpressure release outlet. In the event of pressure being over-generated inside
the appliance, the pressure release device inside the appliance will operate to
discharge the over steam pressure to normal level to prevent the risk of
explosion. The steam will then be released from the tube. NEVER block the tube
outlet. Empty the Drip tray frequently.
Connect to power source, 12:00 will show on display.
Press ON/OFF button once, the red indicator light will be illuminated, and hot
water will come out of the removable brew basket bottom.
After a few seconds, press the ON/OFF button twice again, the red indicator light
will go out and the coffee maker will stop working.
Press down / button, both the yellow and green
indicator will be illuminated and the internal heating element
starts working, the coffee maker begins to pre-heat. When the
Fig. 2
OFF
MIN
HR
ON/OFF PROG
RED INDICATOR: it will be on if
the drip coffee is been made.
12 00
:
Press continuously you can
adjust the hour number.
Press one time the power
for drip coffee can be
switched on or off
YELLOW INDICATOR: The presetting
function is work if the light is on.
Press continuously you can
adjust the minute number.
You can adjust the time set whether it
is present time or presetting time
through press continuously.
YELLOW INDICATOR: The unit is
preheating if it is on; you can turn
the transition switch to froth or
espresso when it goes out.
Power switch for espresso coffee/frothing
YELLOW INDICATOR: Pre-set
function is on.
Press continuously to adjust
the minutes.
Press once to switch
the drip coffee function
ON/OFF
GREEN INDICATOR:
Espresso Coffee/Steam
power is switched on.
Press continuously to
adjust the hours.
RED INDICATOR:
Indicates that drip coffee
has been made.
YELLOW INDICATOR: Indicates
that the unit is pre-heating. You can
turn the transition switch to froth or
espresso when it goes off.
Press button continuously to set
the timer, whether it is to the
present time or pre-set time.

6
yellow is extinguished, you can turn the transition knob to left “ ”position
(see Fig.2) ，the yellow indicator will illuminate again and water will run out of the
metal funnel.
After the water has stopped dripping, you can pour out the water from each
container then clean them thoroughly, now you can start brewing!
NOTE: There may be noise when the machine pumps the water out for the first
time, it is normal; the appliance is just releasing air that is in the appliance. After
about 20s, the noise will stop.
MAKE DRIP COFFEE:
Take off the water tank cover, pour water into the water tank according to the
water level mark in the tank.
Replace the water tank cover, only then must you connect the appliance to the
power supply source, the display will show 12:00.
Add ground coffee to the removable nylon filter with measuring spoon, a spoon of
ground coffee power can make one cup of top-grade coffee, but you can adjust
the taste accordingly ( the max capacity of coffee powder cannot exceed 10
spoons）
Set nylon filter into the removable brew basket and place brew basket into the
coffee maker.
Push drip carafe on the keeping warm plate, make sure that the centre line of the
carafe aligns with that of the brew basket.
Press down the ON/OFF button once, the red indicator will illuminate and coffee
will drip out automatically after a while. NOTE: you can take out the carafe at any
time to serve but the time cannot exceed 20 seconds, otherwise the coffee may
overflow from the edge of brew basket.
The coffee maker will turn to the keep warm function if brewing coffee is finished.
You can switch the power off, otherwise the coffee maker will do
automatically after two hours.
SET THE CLOCK AND PROGRAM AUTOMATIC START-UP (only
fit for making drip coffee)
The appliance has a pre-set function which can be set as follows:

7
Press PROG button once, the word CLOCK will appear at the top-right corner of
the display.
Press the HR and MIN button continuously to set the present time (See fig. 3(1)).
NOTE: if you keep pressing down HR or MIN button more than two seconds, the
hour or minute number on display will increase rapidly.
Press PROG button once again and the word TIMER shows on the bottom left
corner of the display.
You can set the pre-setting time in the same way by pressing HR button and MIN
button continuously, that is 20:15 (see Fig. 3. Note: the word on display will
disappear automatically and enter normal state if no button is touched for more
than 10 seconds at setting state.
Press ON/OFF button two times, the yellow indicator turn on.
The yellow indicator will go off automatically, at the same time the red indicator
will turn on when the time is 20:15 and the unit will start brewing. NOTE：If no
one there, the appliance will cut off power automatically after two hours.
PRE-HEATING FUNCTION:
To make a cup of good hot Espresso coffee, we recommend you pre-heat the
appliance before making coffee, including the funnel, filter and cup, so that the
coffee flavour cannot be influenced by the cold parts.
Take down water tank cover, add water into the water tank. Then replace the
water tank cover.
Set steel mesh into metal filter (WITHOUT coffee powder ), then place them
upwards into the snap and you can fix them into coffee maker firmly by turning it
anticlockwise until it is at the lock position.(See fig. 4).
Place espresso jug on the removable shelf.
Connect the appliance to the power supply. Make sure the transition knob is on
the OFF position.
Press down / button, the yellow and green indicators will both illuminate,
the internal heat element begins to preheat. After about 3 minutes, the yellow
indicator goes out, you can turn the transition knob to now and the yellow will
illuminate again, the coffee will drip down after a few seconds.

8
After making a jug hot water, you must turn the transition
knob to “OFF”position. The preheating process is finished.
MAKE ESPRESSO COFFEE:
Remove the funnel by turning it in clockwise, add ground
coffee to steel mesh with measuring spoon, a spoon of
ground coffee power can make one cup of coffee, then press
the ground coffee powder tightly with the tamper.
Set the steel mesh into metal filter, then place them upwards into the snap and
you can fix them into coffee maker firmly, turn it anticlockwise until it is on the
lock position.
Pour out the hot water in the jug. Place espresso jug on removable shelf. Make
sure that the transition knob is at the OFF position.
At the time, the yellow indicator will go out, you can turn the transition knob to
now and the yellow light will illuminate again, the coffee will start to drip down
after a few seconds. When the jug is filled with coffee, you must turn the
transition knob to “OFF”position.
NOTE: during operating, do not touch the warming jug facility. When moving the
appliance, never carry the handle on the warming jug. The handle is ONLY to
prevent the warming jug from slipping.
If you want to make more coffee, wait for a moment, once the yellow indicator is
extinguished, turn the transition to position and make coffee. You should
press down / button manually when desired coffee is obtained or the colour
of coffee changes, the yellow and green indicator will switch off and the coffee
maker will stop working, at any time, make sure to turn transition knob to the OFF
position, your coffee is ready now!
WARNING: Do not leave the coffee maker unattended while making coffee, as
you may need to operate the machine manually at times!
After making the coffee, you can take the metal funnel out by turning it clockwise,
and then pour the coffee residue out with the steel mesh by pressing the press
bar.
Let the machine cool down completely, before rinsing the parts under running
water.
GENERATE STEAM/ MAKE CAPPUCCINO:
FFig

9
NOTE: Steam function can be used to froth milk(make cappuccino, hot chocolate
and so on) or heat water(make tea and other hot drinks)
Prepare espresso first with espresso jug, make sure that the transition knob is at
the OFF position.
Press down power button / for Espresso coffee, both the yellow and green
indicators below will be illuminated, the internal heat element starts working to
preheat the appliance.
Fill espresso jug/cup with about 100 grams of milk for each cappuccino to be
prepared, you are recommended to use fresh cream milk at refrigerator
temperature (do not heat up the milk)
When the yellow indicator is off, rotate the transition knob on the right side of unit
clockwise to position and the yellow indicator will illuminate again, steam will
come out from the adjustable steam outlet.
Insert the steam outlet into the milk about two centimetre, froth milk by moving
the vessel up and down.
When the required temperature is reached, you can turn the Transition knob to
OFF position to stop the steam generating. NOTE: Clean steam outlet with wet
the sponge immediately after steam stops generating, be very careful when
doing this as the steam may scald you.
Pour the frothed milk into the espresso prepared; now the cappuccino is ready.
Sweeten to taste and if desired, sprinkle the froth with a little cocoa powder.
Press the button / once to cut the power source off.
NOTE: we recommend you allow the coffee maker to cool down for at least 5
minutes otherwise burnt odour may arise in your Espresso coffee and please DO
NOT make drip coffee, espresso coffee or cappuccino at the same time.
CLEANING AND MAINTENANCE
This appliance is for household use only and is not user-serviceable.
Do not open or change any parts by yourself. Please refer to a qualified electrical
service department or return to the supplier if servicing is necessary.
Always remember to unplug the unit from the electrical outlet when not in use
and before cleaning. Ensure that the speed control is set to “0”.

10
It is much easier to clean the accessories directly after they have been used.
Wash them in warm, soapy water, rinse and dry well.
The body of the appliance and the stand should be cleaned with a damp cloth.
Do not let water enter the appliance or the stand.
Do not use bleach or other abrasive substance or solvents to clean your
appliance as it can be damaging to the finish.
Do not immerse the appliance in water or any other liquid, or hold it under a
running tap to clean.
To remove stubborn spots/marks, wipe the surfaces with a cloth slightly
dampened in soapy water or mild non-abrasive cleaner. Rinse and dry a clean,
dry, soft cloth.
STORING THE APPLIANCE
Unplug the unit from the wall outlet and clean all the parts as instructed above.
Ensure that all parts are dry before storing.
Store the appliance in its box or in a clean, dry place.
Never store the appliance while it is still wet or dirty.
Never wrap the power cord around the appliance.
SERVICING THE APPLIANCE
There are no user serviceable parts in this appliance. If the unit is not operating
correctly, please check the following:
You have followed the instructions correctly
That the unit has been wired correctly and that the wall socket is switched on.
That the mains power supply is ON.
That the plug is firmly in the mains socket.
If the appliance still does not work after checking the above:
- Consult the retailer for possible repair or replacement. If the retailer fails to resolve the
problem and you need to return the appliance, make sure that:
The unit is packed carefully back into its original packaging.
Proof of purchase is attached.
A reason is provided for why it is being returned.