Russell Hobbs RHE20 User manual

ESPRESSO MAKER
MODEL RHE20
Instructions & Warranty
RHE20_IB03_300910

Russell Hobbs has been synonymous with life in the kitchen for
over 50 years. Known, owned and proudly on display in
millions of homes across the country. Allow Russell Hobbs to
forge a reputation for timeless, stylish appliances in your home.
Russell Hobbs through and through
Complete range of Russell Hobbs products are available at
www.russellhobbs.com.au | www.russellhobbs.co.nz
Salton (Aust) Pty. Ltd. | P.O. Box 683 Braeside Victoria 3195 Australia | Freecall 1800 427 824
Salton NZ Ltd. | P.O. Box 300 201 Albany Auckland 0752 New Zealand | Freecall 0508 629 777

3
1. ON/OFF switch.
2. ON/OFF lamp.
3. Ready lamp.
4. Steam/Coffee mode switch.
5. Pump START/STOP switch.
6. Filter basket.
7. Handle clip.
8. Filter holder.
9. Drip plate.
10.Drip tray.
11. Measuring spoon/tamper.
12.Milk frother.
13.Steam control.
14.Water tank.
15.Water tank lid.
16.Cup warming tray.
116
11109
14
15
2
4
3
5
6
8
7
13
12

4
Congratulations on the purchase of your Russell Hobbs Espresso Maker. Each unit is
manufactured to ensure safety and reliability. Before using this appliance for the first time,
please read this instruction booklet carefully and keep it for future reference. Pass it on if
you pass on the Espresso Maker.
When using your Espresso Maker, basic safety precautions should be followed.
Carefully remove all contents from the box. As some parts may be packed separately,
check to ensure all items have been removed from the packaging before disposal.
INSTALLATION
 Place the espresso maker on flat, stable surface.
 Ensure the ON/OFF switch is set to the OFF position.
 Connect the plug to the wall power outlet and switch the outlet on.
FILLING THE WATER TANK
 To remove the water tank simply lift upwards off the espresso maker.
 Fill the tank with water at the sink.
 Do not exceed the MAX level on the water tank.
 The tank may also be filled without removing it, simply by pouring water into it directly
from a jug.
 Refit the tank by sliding it down onto the guides at the rear of the espresso maker ensuring
that the valve at the bottom of the tank is located on the water inlet valve of the appliance.
NOTE: Do not operate the espresso maker without water in the tank. Always remember to
top up the water tank with water to keep the water level above the MIN level.
BEFORE FIRST USE
When using this Espresso Maker for the first time, it is very important to flush the unit and
prime the pump.
 Fill water tank to MAX level mark.
 Fit and tighten filter holder in place (refer to the “INSTALLING THE FILTER HOLDER”
section).
 Place a container under the filter holder to catch water.
 Ensure ALL switches are in the outermost position.
 Connect the plug to the wall power outlet and switch the outlet on.
 Press the ON/OFF switch to the ON position.
 Whilst in (coffee) mode, press the pump START/STOP switch to START.
 The pump will start and water from the tank will flow through the system and out of the
filter holder spouts. Watch that the container under the filter holder doesn’t overflow.
 If necessary, press the pump START/STOP switch to stop the pump, then empty container
and continue the procedure until the water tank level nears the MIN level mark.
 Refill the tank.

5
INDICATOR LAMPS
The espresso maker has 2 indicator lamps.
ON/OFF lamp - This lamp illuminates to indicate the unit is on.
Ready lamp - This lamp illuminates only when the water has reached operating
temperature. It will cycle on and off as the thermostat maintains optimum water
temperature.
SELECTOR SWITCH POSITIONS
ON/OFF switch ON OFF
Steam/Coffee mode (steam) (coffee)
Pump START/STOP START STOP
NOTE: To ensure the coffee being made is hot, do not use the brew or steam functions
unless the (Ready) lamp is illuminated.
PREHEATING THE APPLIANCE
NOTE: Always fill the water tank before the espresso maker is turned on and make sure
the steam control is fully closed and all switches are in the outermost position.
 Fit and tighten the filter holder in place as described in ‘INSTALLING THE FILTER
HOLDER’ below.
 Turn the appliance ON by pressing the ON/OFF switch. The ON/OFF lamp will illuminate.
 To ensure the system is properly primed, start the pump by pressing the START/STOP
switch . The pump will start and water will run out from the filter holder spouts. Press the
START/STOP switch again to stop the pump.
 The (Ready) lamp will illuminate once the water in the boiler has fully heated.
 For optimum preheating, the Espresso Maker should be left ON and in (coffee)
mode for approximately 10 minutes before making coffee.
NOTE: Although the optimum preheating time for the appliance is 10 minutes, coffee can
be made once the (Ready) lamp is lit. However, waiting the 10 minutes allows the
boiler to heat fully and espress whole cup(s) at optimum temperature.
INSTALLING THE FILTER HOLDER
 To install the filter holder, hold the filter holder handle and place it level under the
boiler outlet.
 Align the filter holder so that the handle is pointing towards the left hand side of
the appliance.
 Lift the filter holder up ensuring it is fully inserted into the boiler outlet.
 Now rotate the handle to the right until it is tight.

6
PREPARING ESPRESSO COFFEE
NOTE: Always fill the water tank before the espresso maker is turned on and make sure
the steam control is fully closed and all switches are in the outermost position.
It is preferable to preheat the coffee cup(s) before brewing.
 With the espresso maker preheated and filter holder installed, place 1 or 2 cups under
the filter holder and press the pump START/STOP switch to START. Hot water flows
from the filter holder spouts into the cup.
 Press the pump START/STOP switch to STOP when sufficient water to preheat the
cup(s) has been dispensed.
 Discard the preheating water and place the preheated cup(s) onto the warming tray to
retain warmth until cups are needed.
BREWING ESPRESSO COFFEE
NOTE: The filter basket MUST be fitted in the filter holder.
 Fit the filter basket aligning the tip on the outside of the basket to the handle of the filter
holder and drop into place. Rotate the filter basket to lock in.
 Use the measuring spoon/tamper to fill the filter basket with desired amount of ground
coffee and press down (see NOTES below) using the tamper.
 Fit the filter holder into the espresso maker, making sure it is properly tightened.
 Place the preheated cup(s) under the filter holder spouts.
 Confirm the (Ready) lamp is illuminated and press the START/STOP switch to START.
 The pump will start and brewed coffee will pour from the filter holder spouts.
 Press the START/STOP switch to STOP once the desired amount of coffee has been drawn.
NOTES:
Tamping the coffee affects the strength of the espresso. If you press too hard, the coffee
comes out slowly and the crema is dark in colour. If the coffee is not pressed enough, it will
come out too quickly and the crema will be light in colour.
Running the pump after the drawn coffee has changed to a light coffee can make the
coffee bitter.
To make a large cup of espresso coffee prefill the cup with HOT water and draw coffee on top.
REMOVING AND EMPTYING THE FILTER HOLDER
 To remove after brewing, turn the filter holder from right to left.
 Once the filter holder has been removed from the machine, flip the handle clip over and
hold it in place against the filter basket to prevent the filter basket from falling out when
discarding the used coffee grounds.
 To remove the used coffee grounds, grip the filter holder handle and hold the handle clip
firmly against the filter basket. Invert the filter holder and tap it firmly against the edge of
a disposal/kitchen bin.
 Clean the filter basket and holder for future use.
NOTE: During brewing, the filter holder contains boiling water under pressure. To prevent
possible scalding from hot water and steam, never attempt to remove the filter holder from
the espresso maker during the brewing process, whilst the pump is running.

7
CAPPUCCINO & LATTE
A Cappuccino is an espresso with hot milk and a frothy milk top. A latte is basically the
same only with more milk and less froth.
 Prepare your espresso as described above.
 Fill a small jug (preferable metal) with the desired amount of milk. As milk expands when
heated, and to allow additional room for the froth do not fill the jug more than two thirds
full. The jug must be deep enough to cover the end of the frother but without it hitting the
bottom of the jug.
 Do not try to make too much froth at one time. Too much steam will flatten the milk,
leaving you with nothing but hot, watery milk.
HEATING AND FROTHING THE MILK
 Set the Steam/Coffee mode switch to (steam).
 Wait until the (Ready) lamp illuminates.
 Bring the jug containing the milk up to the milk frother and hold it so that the end of the
milk frother is just below the surface of the milk.
 Turn the steam control gradually anti-clockwise to release steam from the milk frother.
 Move the jug up and down slowly, keeping the end of the frother below the surface of
the milk.
 Do not lift the end of the milk frother out of the milk or it will spatter.
 When the milk has warmed to your liking and there is enough froth, turn the steam
control clockwise to close it. Do not overheat the milk or you may adversely affect the
flavour of the coffee.
 To make a cappuccino, pour the heated milk over the crema leaving some room in the
cup, then spoon the froth on top.
 To make a latte, fill the cup by pouring the heated milk over the crema.

8
CLEANING AND MAINTENANCE
 Switch off and unplug the Espresso Maker from the wall power outlet, and let it cool
down fully.
 Grip the filter holder handle and turn the filter holder from right to left for removal.
 To remove the used coffee grounds, grip the filter holder handle and hold the handle clip
firmly against the filter basket. Invert the filter holder and tap it firmly against the edge of
a disposal/kitchen bin.
 Pull the clip back and remove the filter basket.
 Lift the drip tray off the base and lift the cover off the drip tray.
 Wipe the drip tray, drip tray cover and the body of the appliance with a damp cloth.
 Wash the filter and filter holder in warm soapy water. Rinse thoroughly and dry.
NOTE: Do not use solvents or strong detergents when cleaning the espresso maker
cabinet. Use a damp cloth.
CLEANING THE MILK FROTHER AND ENHANCER
After each use of the milk frother, it is
necessary to clean the froth enhancer in the
following manner:
 Check that the steam tube is cool.
 Remove the froth enhancer by sliding it
off the end of the steam tube and rinsing
in warm water.
 Wipe over the steam tube and nozzle
with a damp cloth.
 Refit the froth enhancer by sliding back
on the steam tube and pressing upwards
to lock.
At least once a month, it is necessary to
clean the steam outlet in the following
manner:
 Check that the espresso maker is cool
and the plug is detached from the wall
power outlet.
 Remove the froth enhancer.
 Using the measuring spoon/tamper
spanner, loosen the steam nozzle, unscrew
from the end of the steam outlet tube.
 Carefully remove the steam nozzle and
wash it together with the froth enhancer in warm soapy water. Rinse thoroughly.
 Extra care should be taken to ensure the hollow centre of both items is clean and clear of
milk residue.
 Using a damp cloth, clean the steam tube.
 Refit the steam nozzle to the steam tube and gently tighten using measuring spoon/
tamper spanner.
 Refit the froth enhancer.
STEAM TUBE
FROTH
ENHANCER
STEAM
NOZZLE

9
CLEANING THE ESPRESSO BOILER OUTLET
At least twice a year, it is necessary to
clean the outlet of the espresso boiler in
the following manner:
 Check that the espresso maker is cool
and the plug is detached from the wall
power outlet.
 Using a screwdriver, unscrew the screw
in the outlet of the espresso boiler.
 Carefully remove the screw, shower
head, spring and pressure valve.These
parts can all be washed in warm soapy
water and rinsed thoroughly.
 Extra care should be taken to clear
the holes around the side of the outlet
screw.
 Using a damp cloth, clean the boiler outlet.
 Refit the parts into the espresso boiler outlet.
DESCALING
It is advisable to clean the scale from the appliance at least once a year.
CLEANING PROCEDURE
 Dissolve 2 teaspoons of citric acid in 1 litre of water. Add solution to water tank.
 Press the ON/OFF switch to the ON position. Select (coffee) mode. Wait until
the (Ready) lamp illuminates.
 Check that the filter holder is not attached and place a container under the boiler outlet.
 Press the pump START/STOP switch to START and allow half of the solution in the tank
to flow out. Press the pump START/STOP switch to STOP.
 Allow solution to sit for approx 15 minutes. Press the pump START/STOP switch to
START and run until the tank level reaches the MIN level.
 To flush out the remains of the solution and the scale, remove the tank, rinse well, fill
with clean water and refit.
 Press the pump START/STOP switch to START, and allow half of the solution in the
tank to flow out. Press the pump START/STOP switch to STOP. Wait a few minutes and
repeat until the tank reaches the MIN level.
 Repeat the previous 2 steps.
PRESSURE VALVE
BOILER OUTLET
SPRING
SHOWER HEAD
OUTLET SCREW

10
When using your Espresso Maker, basic safety precautions should be followed, including
but not limited to the following:
IMPORTANT SAFEGAURDS:
1. This appliance uses steam under pressure. Improper use may result in a scalding injury.
2. To protect against electrical hazards do not immerse the power cord, plug or appliance in water or
any other liquid.
3. Do not use in a bathroom or near any source of water.
4. Do not use outdoors.
5. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
6. This appliance is not a toy. Children should be supervised to ensure they do not play with this
appliance.
7. Sit the espresso maker on a stable, level, heat-resistant surface.
8. Do not leave the espresso maker unattended while plugged in and switched on. Always monitor
when in use.
9. Do not touch hot surfaces.
10.When using the milk frother always keep your fingers away from the steam.
11. Use only clean, cold, fresh water. Do not fill the water tank with milk or any other liquid.
12.Do not fill above the ‘MAX’ mark indicated on the water tank.
13.Keep the appliance and power cord away from the edge of countertops and out of reach of
children and infirmed persons.
14.Keep the appliance and power cord away from hotplates, all hot surfaces and burners.
15.Route the power cord so it doesn’t overhang, and cannot be tripped over or caught.
16.Do not use the espresso maker near or below curtains or other combustible materials.
17.Do not place the appliance under cupboards, shelves or anything that might be damaged by heat
or steam.
18.Unplug the espresso maker when not in use, before moving or cleaning. Let it cool down before
cleaning and storing away.
19.Use only accessories or attachments supplied for specific use with the Russell Hobbs espresso
maker.
20.Do not use the espresso maker for any purpose other than those described in these instructions.
21.There are no user serviceable parts. If the power cord is damaged, it must be replaced by the
manufacturer or a similarly qualified person in order to avoid a hazard.
22.Do not operate this appliance with a damaged power cord/plug or after the appliance has
malfunctioned, or been dropped or damaged in any manner. Contact customer service for
examination, adjustment, repair or replacement.
23.To disconnect, turn off the wall power outlet then grasp the plug and remove from wall power
outlet. Never pull by the cord.
24.Never install the espresso maker in an environment that can reach a temperature less than or
equal to 0°C. If the water freezes, the espresso maker may be damaged.
25. This appliance is not intended to be operated by means of an external timer or separate control system.
SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS FOR HOUSEHOLD USE