Russell Hobbs 10787 User manual

INSTRUCTIONS/WARRANTY
MODEL: 10787
RUSSELL HOBBS BRITA FILTER KETTLE

2
INTRODUCTION
Thank you for purchasing the Russell Hobbs BRITA Filter Kettle.
Each unit has been manufactured to ensure safety and reliability
and ease of use. Before use, please read these instructions
carefully and keep them for further reference.
IMPORTANT SAFEGUARDS
When using your Russell Hobbs BRITA Filter Kettle, basic
precautions should always be followed including the following:
•Make sure the power used corresponds to the one indicated on
the rating label.
•Always place the unit on a flat, level surface.
•Do not operate without water in the kettle.
•Read carefully and save all these instructions for future
reference.
•Don’t fill past max, or it may spill boiling water.
•Do not fill with hot or boiling water
•Always turn the power off at the power outlet before you
insert or remove a plug. Remove by grasping the plug – do not
pull on the cord.
•Before switching on, check that:
oThe kettle contains at least 2 cups of water
oThe water is not above the –MAX- mark on the water level
indicator
oThe lid is fully closed (otherwise it may not switch off)
oThe lid is properly located on the power base
•Turn the power off and remove the plug when the appliance is
not in use and before cleaning.
•Do not use your appliance with an extension cord unless this
cord has been checked and tested by a qualified technician or
service person.
•Water can remain hot for a considerable time after boiling and
can present a scald hazard. Keep the kettle, power base and
mains lead away from the edges of worktops and out of reach
of children.
•Use the kettle only with the power base supplied (and vice
versa).
•Close supervision is necessary when the appliance is being used
near children or irresponsible persons.
•Never leave an appliance unattended whilst in use.
•Disconnect the plug from the power outlet prior to cleaning
the appliance.
•Do not allow the power cord to come into contact with the hot
parts of the machine.
•Keep hands away from hot parts of the appliance, including the
body and spout.

3
•Do not use an appliance for any purpose other than its
intended use as described in this instruction book.
•Do not place an appliance on or near a hot gas flame, electric
element or on a heated oven.
•Do not place on top of any other appliance.
•Do not let the power cord hang over the edge of a table or
bench top or touch any hot surfaces.
•For safety reasons and to avoid maintenance by unskilled
persons, some appliances are ‘sealed’ using tamperproof
screws. Such appliances should always be returned to the
nearest appointed Russell Hobbs agent for adjustment or repair,
if required.
•Do not operate any electrical appliance with a damaged cord or
after the appliance has been dropped or damaged in any
manner. If damage is suspected, return the appliance to the
nearest Amalgamated Appliances Service Centre for
examination, repair or adjustment.
•Once the packaging has been removed, check the appliance is
in full working order. If in doubt, do not use the appliance and
contact qualified service staff.
•Packaging material (plastic bags, foam polystyrene, etc.) should
not be left within reach of children as they could be a potential
source of danger.
•Use drinking water only in this kettle. Do not put any other
liquids or food products in this appliance. Do not mix or add
anything to the water placed in this appliance, except as
instructed in this Instruction Book.
•Do not attempt to move the kettle if is contains liquids.
•Do not put kettle body into a microwave.
•Do not open the hinged kettle lid during brewing, as hot steam
comes out of the kettle during operation.
•This appliance is for domestic use only. Any other use is to be
considered improper and invalidates the warranty.
•Do not immerse the appliance in water or any other liquid
unless recommended.
•The appliance’s power-cable must not be replaced by the user,
as special tools are required. In the event of damage to the
cable, or if the cable needs replacing, contact the nearest after-
sales assistance centre authorized by the manufacturer.
•This appliance generates heat and escaping steam during use.
Use proper precautions to prevent the risk of burns, fires, and
other injury to person or property.

4
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
NAME AND PARTS LOCATION
NAME AND PARTS LOCATION
1. Power on/off button with backlight
2. Handle
3. Lid with pour through lid and BRITA “Memo”
4. Lid locking tab
5. Pour through lid
6. BRITA “Memo” – the electronic filter cartridge exchange indicator
7. Filter funnel to hold the BRITA MAXTRA cartridge
8. Funnel handle
9. BRITA MAXTRA water filter cartridge
10. Spout
11. Body
12. Window with water-level scale
13. Base with power cord storage system
14. Power plug
15. Additional lid for boiling water without filter

5
BEFORE USING YOUR RUSSELL HOBBS KETTLE FOR THE FIRST TIME
Warning:- To reduce the risk of electric shock, the power cord
must be disconnected before performing any maintenance or
trouble shooting checks.
Carefully unpack the kettle and remove all protective packing
materials. You may wipe the outside of the kettle using a clean
damp cloth. Do not use any type of harsh abrasive cleaners.
Do not immerse the base, cord or body in water or any other
liquid. To remove any dust that may have accumulated in the
removable parts during packing, fill to max, boil, discard the
water, and then rinse again with clean water.
POSITION
Position the power base on a stable, level surface, close to an
electrical power supply. Route the mains lead so that it doesn’t
overhang, and can’t be caught accidentally or tripped over. Wind
any excess mains lead round the cord storage area beneath the
power base and bring it out of the cord exit in the side of the
base and away from the reach of children.
FILLING WITH DRINKING WATER
1. Make sure the kettle is not in the ON position.
2. Remove the kettle from its base/stand.
3. Press the lid release button on the lid. This will release the lid
locks. You can now insert a finger under the lid and lift it open.
4. Fill the kettle via the lid opening.
5. Fill the kettle with at least 2 cups of water, but don’t fill past
the max mark. If you overfill the kettle, it may spill boiling
water from the spout.
6. Close the lid, and press the lid down so that the lid locks into
place. Check that the lid is fully closed, otherwise the kettle
may not switch off when it boils.
Warning:- Keep clear of the spout and lid areas as steam will
escape from the lid, which could be a potential hazard.

6
PREPARING THE BRITA MAXTRA FILTER CARTRIDGE FOR USE :
•Remove protective wrapper (NOTE : cartridge and inside
wrapper may appear moist, this is simply condensation)
•Immerse cartridge in cold water and shake it gently to remove
any air bubbles – NOTE :As is required for some other water
filter cartridges, there is no need to pre-soak the new MAXTRA -
cartridge.
•Place the BRITA MAXTRA filter cartridge (9) into the funnel (7)
and push downwards until it firmly fits into the funnel. The
cartridge should stay in place, if the funnel is turned upside
down.
•Fill the funnel with cold tap water and allow it to filter through.
•Discard the first two fillings or use the water for your
plants.
•These first two fillings are used to flush the filter -
cartridge.
•Now re-fill the funnel and the kettle is ready for use.
•Install the lid (3) onto the funnel. (7)
•There is no need to keep the cartridge immersed in water.
•Turn the kettle on by pressing the power on button (1) – after
the water has boiled, the kettle will turn off automatically.
•NOTE: Please remember that water is a foodstuff. -Please
consume filtered water within one to two days.
EXCHANGING THE FILTER:
To exchange the cartridge (after 4 weeks) simply use the ring pull
handle on the top the cartridge to remove it from the funnel.
NOTE: When buying new cartridges look for the original BRITA
MAXTRA symbol on the cartridge packaging to find the correct
filter cartridge in the shop.
Prepare the new BRITA MAXTRA filter cartridge for use as detailed
above and install into place.

7
THE BRITA MEMO
For maximum filter performance and for optimum taste, it is
important to change your BRITA cartridge regularly. BRITA
recommends that you replace the cartridge in your appliance
every 4 weeks.
BRITA - Memo automatically reminds you when to change the
cartridge.
The unique BRITA Memo measures the recommended time of
use of your cartridge. Memo is easy to use and automatically
reminds you when to change your cartridge. The BRITA Memo
is located on the lid of your kettle. Operation is really simple:
•Start the Memo Display:
To start the Memo please press and hold down the start
button on the lid until all four bars appear in the display
and flash twice. The Memo is now set.
•Functional Control:
The flashing dot in the bottom right corner of the Memo
indicates that the Memo is working.
•Change Display:
After every week one bar will disappear to show the
remaining cartridge life. - After 4 weeks all four bars will
disappear.
This and a flashing arrow indicate that the cartridge
should now be changed.
Insert a new cartridge according to the instructions and
re-activate the Memo as described above.

8
SWITCHING ON
To start with, make sure the kettle switch is in the OFF position.
Plug the stand into the wall socket. If necessary, switch the wall
socket to the ‘ON’ position.
Gently position the kettle on the stand – take care not to spill.
Press the ‘ON/OFF’ switch down. The light in the switch will come
on, and the kettle will start heating up.
SWITCHING OFF
When the water boils the kettle will switch off, the switch will
return to the off position, and the light will go out.
To switch off manually, simply press the ‘ON/OFF’ switch up.
GENERAL DETAILS
Remove the kettle from the stand before pouring.
To avoid the risk of splashing, pour slowly and don’t over-tilt the
kettle.
Don’t tilt the kettle backwards, water might get on to the control
area. If this happens, let the kettle dry before use – sit it
somewhere dry & warm for about 12 hours.
When you lift the kettle, you may see moisture on the stand. Don’t
worry – it’s the steam used to switch off automatically, which
then condenses and escapes via vents under the kettle.
INSUFFICIENT WATER
This will shorten the life of the element. A boil-dry cut-out will
switch the kettle off. Remove the kettle from its stand, and sit it
on the work surface until it is cold. Don’t fill it unless it’s cold – if
the element is still hot, it may splash water, which could be a
potential hazard.
CARE & MAINTENANCE
Switch the kettle off by pressing the ‘ON/OFF’ - switch in the up
direction.
Unplug the stand from the wall socket and let the kettle cool
down fully before cleaning.
Wipe the kettle, inside and out, with a damp cloth. Then buff with
a soft dry cloth.
Keep all connectors and sockets dry.

9
Don’t put the kettle or stand in any liquid.
Don’t use harsh or abrasive cleaners or solvents.
BRITA MAXTRA WATER FILTER – SEE ALSO INSTALLING FILTER
INSTRUCTIONS ABOVE
The new BRITA MAXTRA water filter cartridge reduces limescale
(carbonate hardness) aluminium and certain heavy metals (like
lead and copper), as well as substances that affect smell and taste
such as chlorine and organic impurities.
The unique BRITA Memo indicates when to change the MAXTRA
cartridge.
Change the BRITA MAXTRA filter cartridge regularly.
NOTE: More information on the use of BRITA filter cartridges
and the Memo can be found in the BRITA information guide.
CLEANING THE FUNNEL
1. Check your hands are free from soap, or anything, which
might leave a taint.
2. Switch the kettle off – press the switch upwards, and let the
kettle cool down completely.
3. Open the lid.
4. Grip the top of the funnel and pull it back away from the top
of the spout, then lift it out of the kettle.
5. Take out the BRITA MAXTRA cartridge.
6. Brush the funnel with a soft brush under a running tap.
7. Rinse the kettle, in case any scale particles have fallen inside.
8. Fit the bottom of the lid into the bottom of the spout, then
press the top forward till it clicks into place on the top of the
spout.
9. Put the BRITA MAXTRA cartridge back into the funnel
10. Close the lid.
11. Press the lid down to make sure it is properly closed.

10
DESCALE REGULARLY – EVEN IN ‘SOFT’ WATER AREAS
Should descaling be necessary, remove the BRITA MAXTRA filter
cartridge before descaling.
After the descaling process put the BRITA MAXTRA filter cartridge
back into the thoroughly cleaned kettle.
Limescale may be white, coloured, even rusty-looking, but is
usually visible.
Phosphate scale isn’t generally visible, but it is there, even in soft
water areas.
All scale causes overheating, reduces the kettle’s life, and may
trigger the boil-dry cut-out so even with soft water, de-scale
regularly, to help keep your kettle in working order for longer.
Use a descaler suitable for plastic products (all kettles have plastic
parts). Follow the instructions on the de-scaler, then fill and
operate with clean water only, to remove any residues. Do not use
or drink the water which was used to de-scale the kettle with.
CHANGING THE FITTED/MOULDED PLUG
Should the need arise to change the fitted/moulded plug, follow
these instructions:
Mains (AC) Operation
This unit is designed to operate on 230V current only.
Connecting to other power sources may damage the unit.
Connect three-pin plug as follows:
The wires in this mains lead are coloured in accordance with the
following code: Green/Yellow = Earth Blue = Neutral
Brown = Live

11
SERVICE/ PROBLEM SOLVING
There are no user serviceable parts in this appliance. If the
appliance is not operating correctly, please check that:
1 You have followed the instructions correctly.
2. The unit has been wired correctly and the wall socket
is switched on.
3. The kettle body is in place.
4. The mains power supply is ON.
If the appliance still does not work:
In the first instance, consult your retailer for possible repair or
replacement. If your retailer fails to solve your problem and you
need to return the appliance, make sure that:
1. The unit is packed carefully, complete in its original
packaging.
2. Proof of purchase is attached.
3. Give the reason why you are returning it.
If service becomes necessary within the warranty period the
appliance should be returned to an approved Amalgamated
Appliances (Pty) Ltd Service Centre. Servicing outside the warranty
period is still available, however it will be chargeable.
PLEASE AFFIX YOUR PROOF OF PURCHASE/RECEIPT HERE.
IN THE EVENT OF A CLAIM UNDER WARRANTY, THIS RECEIPT MUST
BE PRODUCED.

12
W A R R A N T Y
Amalgamated Appliances (Pty) Limited (“the Supplier”) warrants
to the original purchaser of this product (“the Customer”) that
this product will be free of defects in material and
workmanship which under normal, personal, family or
household purpose manifest themselves within a period of 365
days from the date of purchase or in respect of commercial or
professional purposes, manifest themselves within a period of
90 days from the date of purchase. Any claim in terms of the
warranty must be supported by a proof of purchase. If such
proof is not available, then notwithstanding anything to the
contrary herein, the Supplier’s normal charge for service and/or
spares will be payable by the Customer upon collection of the
repaired product. If a claim is made in terms of the aforesaid
warranty within the first 7 days from the date of purchase, the
faulty product will be exchanged (provided that the product is
in its original packaging with all accessories). Failing return of
the product within 7 days, the Supplier’s liability shall be
limited on return to the Supplier of the product or parts
thereof, to the replacement or repair (in the sole discretion of
the Supplier, or its duly authorised service dealer) of the
product to eliminate any defect in workmanship or materials
found to be due exclusively to any acts or omissions on the
parts of the Suppliers, of which defects the Supplier shall have
been notified in writing by the Customer within the aforesaid
warranty period. The warranty provided herein and the
obligations of the Supplier as aforesaid are in lieu of, and the
Customer waives, all other warranties, guarantees, conditions
or liabilities, express or implied, arising by law or otherwise,
including without limitation, any obligation of the Supplier in
respect of any injury, loss or damage (direct, indirect or
consequential) arising out of the use of, or inability to use,
this product and whether or not occasioned by the Supplier’s
negligence (gross or otherwise) or any act or omission on its
part. The warranty does not include and will not be construed
to cover products damaged as a result of disaster, misuse,
abuse or any non-authorised modification of the product. The
warranty does not include replacement of light bulbs, heater
bars, paper bags or any glass, plastic bowl or jug or other
expendables. During the warranty period the product should
be taken to a service centre of the Supplier or one of its duly
authorised service agents. The Supplier neither assumes nor
authorises any other person to assume for it, any additional
liability in connection with the sale or servicing of its products.

13
AMALGAMATED APPLIANCES (PTY) LTD.
29 HERONMERE ROAD PO BOX 39186
BOOYSENS, JOHANNESBURG BOOYSENS
2016 2016
JOHANNESBURG TEL NO. [phone]
FAX NO. [phone]
CAPE TOWN TEL NO. [phone]
DURBAN TEL NO. [phone]
Win prizes on line: www.russellhobbs.co.za