Russell Hobbs RHSWD3 Installation guide

INSTURCTIONS AND WARRANTY
RHSWD3
RUSSELL HOBBS FREE STANDİNG WATER DİSPENSER

2
Congratulations on purchasing our Russell Hobbs Water Dispenser. Each unit is manufactured to
ensure safety and reliability. Before using this appliance for the first time, please read the instruction
manual carefully and keep it for future reference.
FEATURES OF THE RUSSELL HOBBS WATER DISPENSER
•Hot, cold and ambient water options
•Hot Water Temperature and Heating Capacity: 85-95℃5L/h.
•Cold Water Temperature and Cooling Capacity: 8-12℃2L/h .
•Heating Power:500W
•Cooling Power: 85W/90W
•Over-Current Protection
•Automatic Thermostat Technology
•All the plastic parts are made of anti-bacteria ABS
•For domestic use only
•2 year warranty
IMPORTANT SAFEGUARDS
1. Always ensure that the voltage on the rating label corresponds to the mains voltage in your
home.
2. Your appliance has been designed for household and workplace use only.
3. Your close supervision is necessary when the appliance is used by children, people having
insufficient experience and knowledge, physically (audio, visual) or mentally handicapped
people. Make sure that children do not play with the appliance.
4. Use of an extension cord with this appliance is not recommended. However, if it is necessary
to use an extension cord, ensure that the cord is suited to the power consumption of the
appliance to avoid overheating of the extension cord, appliance or plug point. Do not place the
extension cord in a position where it can be pulled on by children or animals or tripped over.
5. Your water dispenser should be at least 30 cm away from heat sources such as furnace, oven,
heater core, stove and electric oven, and should not be kept under direct sunlight.
6. For efficient operation of your water dispenser, ambient temperature should be minimum 6°C
and maximum 30°C.
7. Safe operating temperature of the appliance is 45°C.
8. Leave sufficient space (10-20cm) behind the water dispenser to allow for good ventilation
9. If two water dispensers are placed side by side, at least 2 cm space should be left between
them.
10. Ensure that your water dispenser stands balanced on the flat, level ground. This should be
done before the dispenser water bottle is placed.

3
11. Before using your water dispenser, rinse out any dust (Due to transportation).This can be
done by running water through the dispenser taps. Empty at least one dispenser water bottle.
Then empty the tanks completely by opening the water discharge stopper at the back of the
water dispenser.
12. To prevent damaging the heating system, never operate the heating function before water
comes out of the hot water tap.
13. While using the product, do not put a new dispenser water bottle before water in the current
dispenser water bottle is completely finished. This maintains the water level inside the water
dispenser.
14. In case of technical problems, switch off the machine and do not attempt to repair it yourself.
Return the appliance to an authorized service facility for examination, adjustment or repair.
Always insist on the use of original spare parts. Failure to comply with the above mentioned
pre-cautions and instructions, could affect the safe operation of this machine.
15. Remove the plug from the socket by gripping the plug. Do not pull on the cord to disconnect
the water dispenser from the mains. Always unplug the water dispenser when it is not in use,
before cleaning, during maintenance or when removing/adding parts.
16. Only use dispenser water bottles that have been designed for this water dispenser. The use of
accessory attachments that are not recommended or supplied by the manufacturer may result
in injury, fire/electric shock or may damage the water dispenser.
17. Tear the hygienic label off the pre-filtered water bottle. Alternatively assemble the Russell
Hobbs Purification and Mineralization bottle (RHPM1) suited especially for this unit.
18. Place the bottle reversely into the water protector on the top part of the water dispenser.
19. Keep away from other electronic appliance, e.g. TV, CD player or Stereo system.
20. Store the water dispenser in a cool, shadowed area .
21. Do not use the water dispenser as a supportive structure.
22. Do not use the water dispenser if it has been dropped or damaged in any way.
23. Do not puncture or damage the gas channels at the back of the water dispenser. If cooling gas
comes into contact with skin or eyes it may cause irritation or injury. Please contact a health
practitioner.
24. Do not cover the water dispenser or place objects where they can block the top of the water
dispenser.
25. Children should be supervised to ensure that they do not play with the water dispenser.
26. This product has been produced only for water heating and cooling purpose. Do not use it for
cooling buttermilk drink, lemonade or drinks with high percentage of alcohol.
27. Never keep products containing flammable gas (e.g. spray) and explosive materials near your
appliance.
28. Do not tilt your appliance more than 45° during transportation or relocation.
29. Do not use damaged dispenser water bottles
30. To prevent damage to the heating system, never operate the heating function before water
comes out of the hot water tap.

4
31. Do not use hot water function if there is no water bottle on the water dispenser
32. If water trap fills during daily use, please empty accumulated water.
33. Do not switch the cooling function between on and off positions within 3 minutes. This is
important to protect the compressor.
34. In case of technical problems, switch off the water dispenser and do not attempt to repair it on
your own. Take the water dispenser to an authorized service facility for examination,
adjustment or repair. Always insist on the use of original spare parts. Failure to comply with
the above mentioned precautions and instructions could affect the safe operation of the water
dispenser.
PARTS DIAGRAM
1-Top cover
8-Cold water taps
2-Power indicator
9-Hot water taps
3-Heating indicator light
10-Cold water tank
4-Cooling indicator light
11-Hot water tank
5-Heating switch
12-Compressor
6-Cooling switch
13-Drip box
7-Cold thermostat
14-Fuse
15-Condenser

5
PAY ATTENTION TO THE FOLLOWING POINTS IN THE FIRST OPERATION OF THE WATER
DISPENSER:
1. In order to prevent any damage to the heating system; do not plug in the water dispenser
before water comes out of the hot water tap.
2. Do not switch the cooling function on within the first 6 hours of operation
3. If power failure has occurred within the first six hours of use; pay attention to the warnings
under the title of “ IN CASE OF POWER FAILURE”
DURING THE TRANSPORTATION
Original packages and foams may be required for transportation of your water dispenser.
Points to consider during re-transportation of the product;
•Your water dispenser should be emptied and cleaned before the transportation.
•Accessories of your water dispenser should be taped down to prevent movement during
transportation.
•Condenser pipes on the back of the water dispenser should be protected against impact and
perforation before the packaging.
•The packaged water dispenser should be securely packed into the transportation vehicle.
Packaging instructions on the box should be adhered to.
•Your appliance should not be tilted more than 45° during the transportation. Should the water
dispenser be tilted more than 45˚ or stored horizontally, it should be kept in a vertical (upright
position) for a minimum of 6 hours before operating.
NECESSARY ACTIONS FOR ENERGY SAVING
1. Do not put hot water into the water dispenser.
2. Do not place your water dispenser near heat emitting appliances such as an oven, dishwasher
or heater, or in direct sunlight.
3. Be sure to switch off the water dispenser if it is not going to be in use for a long period of time.
NOTE: Empty the water dispenser completely, by opening the tap and letting all the water drain out.
Then open the drain valve at the back of the water dispenser and let the water drain out completely. If
water is left in the water dispenser for long periods of time, it will begin to smell and may cause
damage to the water tank.

6
PREPARATION FOR OPERATION OF THE WATER DISPENSER;
1. Tear the hygienic label on the dispenser water bottle. Place the dispenser water bottle into the
water protector on the top of the water dispenser.
2. Internal center of the water protector opens and clogs the valve automatically when using the
pre-filtered water bottle. It will automatically turn off in order to prevent probable water leakage
on the valve.
3. Push the hot water tap. Bubbles flowing in the bottle will indicate that water in the bottle is
flowing into the hot water tank. Continue pressing the hot water tap until water in the hot water
tank stops.
4. Plug your water dispenser in and it will now be ready to use.
INSTALLATION
1. Your water dispenser has three taps namely, hot, cold and ambient water.
2. Turn on both the ‘red’ and ‘green” power switches found at the back of your unit for your hot
and cold water.
3. The cold water indicator light will illuminate ‘green’, the power indicator light will illuminate
‘yellow’ and the hot water indicator light will be illuminate ‘red’. This means that the heating
system will start to operate.
4. When the ‘red’ indicator light turns off automatically, the water temperature will have reached
the ideal temperature of 85-95°C. When the water temperature reduces to 80°C, the ‘red’
indicator light will illuminate automatically and the water temperature will increase again.
5. If you do not want to use hot water, turn off the hot water power switch at the back of your unit
and the water will be at normal temperature.
CLEANING AND CARE
•Before cleaning, disconnect the power of your water dispenser by unplugging it from the wall
socket.
•Never use vapor or steam cleaning materials for cleaning purpose. Do not spray water directly
onto the water dispenser. This may cause a short circuit or electric shock, should the water/
water vapour come into contact with the electrical circuits.
•Clean the outer surfaces of the water dispenser by wiping with a soft damp cloth. Do not use
abrasive cleaners such as bleach or detergents. Use a little baking soda dissolved in warm
water.
•Keep the area around the water dispenser free of dust by using a brush or vacuum cleaner. If
the condenser becomes dirty, clean with a soft damp cloth.

7
•Dry the appliance completely after cleaning.
CAUTION: In case of sudden power failure after first use, unplug the unit, as the pressure of
gas in the cooling system of your appliance has not been balanced yet.
IN CASE OF ANY POWER FAILURE
•Within the first six hours of the first use, unplug the water dispenser, wait for one hour then
plug in the water dispenser.
•If it occurs after the first six hours of operation, your appliance will start to operate
automatically after 10 minutes.
•If your appliance has not started to cool after the above mentioned time periods, call the
Authorized Service Centre.
TROUBLESHOOTING
Trouble
Probable Cause
Water dispenser does not operate
It is not plugged in.
Fuse has blown or failed.
Water which comes from cold water tap is not
sufficiently cold.
Ensure that cold water button on the back is
switched on
Water dispenser has not been placed far enough
away from the wall.
Water dispenser does not heat the water.
Ensure that hot water button on the back is
switched on.
Surface of the heater in the hot water tank may
have been calcified. Read and apply the text of
cleaning the water dispenser.
Compressor is operating and stopping
frequently
Room temperature is over the normal.
Water dispenser has not been placed on the
distance sufficiently far from the wall.
Water dispenser vibrates
Ensure that the water dispenser is placed on a
level surface.
Water dispenser is noisy.
Noise may be caused from flow of cooling agent,
this is normal.
You can hear a flow sound at the end of each
circulation.
Clinking sounds may occur as a result of
contraction and expansion because of heating
and cooling of water tanks.
Ensure that the water dispenser is placed on a
level surface.

8
SERVICING THE APPLIANCE
There are no user serviceable parts in this appliance. If the unit is not operating correctly, please
check the following:
-You have followed the instructions correctly
-That the unit has been wired correctly and that the wall socket is switched on.
-That the mains power supply is ON.
-That the plug is firmly in the mains socket.
If the appliance still does not work after checking the above:
- Consult the retailer for possible repair or replacement. If the retailer fails to resolve the problem and
you need to return the appliance, make sure that:
- The unit is packed carefully back into its original packaging.
-Proof of purchase is attached.
-A reason is provided for why it is being returned.
If the supply cord is damaged, it must be replaced by the manufacturer or an authorised service agent,
in order to avoid any hazard. If service becomes necessary within the warranty period, the appliance
should be returned to an approved Home of Living Brands(Pty) Ltd service centre. Servicing outside
the warranty period is still available, but will, however, be chargeable.
CHANGING THE PLUG
Should the need arise to change the fitted plug, follow the instructions below.
Connecting to other power sources may damage the appliance. Connect a three-pin plug as follows:
The wires in this mains lead are coloured in accordance with the following code:
Green/Yellow = Earth
Blue = Neutral
Brown = Live

9
PLEASE AFFIX YOUR PROOF OF PURCHASE/RECEIPT HERE
IN THE EVENT OF A CLAIM UNDER WARRANTY THIS RECEIPT MUST BE PRODUCED.
2 YEAR WARRANTY
1 year retail ⵏ1 year
extended warranty upon
registration*
visit www.russellhobbs.co.za
W A R R A N T Y AND EXTENDED WARRANTY
1. Home of Living Brands (Pty) Limited ("Home of Living Brands") warrants to the original
purchaser of this product ("the customer") that this product will be free of defects in quality and
workmanship which under normal personal, family or household use and purpose may
manifest within a period of 1 (one) year from the date of purchase ("warranty period").
2. Home of Living Brands shall extend the warranty period for a further period of 1(one) year
(“extended warranty period*”), on condition that the purchaser registers the product on the
website, within 12 months from the date of purchase of the product. The website address for
registration is as follows: http://russellhobbs.co.za/info-pages/warranty-info.aspx. The
extended warranty period only applies to products purchased on or after 1 October 2017.
3. Where the customer has purchased a product and it breaks, is defective or does not work
properly for the intended purpose, the customer must notify the supplier from whom the
customer bought the product ("the supplier") thereof within the warranty period or if applicable,
the extended warranty period. Any claim in terms of this warranty must be supported by a
proof of purchase. If proof of purchase is not available, then repair, and/or service charges
may be payable by the customer to the supplier.
4. The faulty product must be taken to the supplier's service centre to exercise the warranty.
5. The supplier will refund, repair or exchange the product in terms of this warranty subject to
legislative requirements. This warranty shall be valid only where the customer has not broken
the product themselves, or used the product for something that it is not supposed to be used
for. The warranty does not include and will not be construed to cover products damaged as a
result of disaster, misuse, tamper, abuse or any unauthorised modification or repair of the
product.
6. This warranty will extend only to the product provided at the date of the purchase and not to
any expendables attached or installed by the customer.
7. If the customer requests that the supplier repairs the product and the product breaks or fails to
work properly within 3 (three) months of the repair and not as a result of misuse, tampering or
modification by or on behalf of the customer, then the supplier may replace the product or pay
a refund to the customer, subject to the supplier’s discretion.
8. The customer may be responsible for certain costs where products returned are not in the
original packaging, or if the packaging is damaged. This will be deducted from any refund paid
to the customer.
HOME OF LIVING BRANDS (PTY) LTD (JOHANNESBURG)
JOHANNESBURG TEL NO. [phone]
CAPE TOWN TEL NO. [phone]
DURBAN TEL NO. [phone]
www.homeoflivingbrands.com
www.russellhobbs.co.za
www.facebook.com/RussellHobbsSA