Russound AVA Series User manual

AVA-Series Amplifiers
AVA2.1 & AVA3.1
INSTALLATION GUIDE

2
AVA-Series Amplifiers
OVERVIEW
Russound’s AVA-Series’s are a game changer in the audio industry. Their built
-in HDMI ARC input with CEC control means that these compact, powerful,
low-profile AVA-Series can be used seamlessly with any modern television
without the need for any remote control other than your native TV or cable-
box/satellite remote that is already being used. If desired, their multiple
inputs can be used to convert the AVA-Series into a mini-receiver supporting
up to 4 total inputs (HDMI, Digital Optical, Line-Level Stereo, Bluetooth) and
they include an external IR sensor and full-featured remote control.
WHAT’S IN THE BOX
(1) AVA-Series Amplifiers
(1) 6’ (1.8m) Power Cord (US Version)
(3) 6’ (1.8m) Power Cords: Euro, UK and AUS (International Version)
(1) Removable, Screw-Down Speaker Connector (accepts up to 14AWG wire,
4-pin or 6-pin depending on the model purchased)
(1) Mounting Bracket
(2) Mounting Screws - #8 1-1/4” (3.18 cm) Phillips
(1) External IR Sensor with 3’ cable
(1) 3’ (.91m) HDMI Cable
(1) Remote Control
(2) AA Alkaline Batteries
(1) Owner’s Manual
WHAT YOU NEED FOR THE INSTALLATION
Flat Mini-screwdriver for the speaker connectors
#2 Philips Screwdriver for Wall-mounting (if desired)
Wire Strippers
INSTALLATION OPTIONS
The compact, low-profile design of the AVA-Series Amplifierss allows them
to be installed out of view, minimizing any intrusion into the customers’ living
space. There are several options available to choose from to meet any need.
Please keep in mind that the AVA-Series Amplifierss support Bluetooth Audio so
that any audio content from a phone, tablet, or computer can be easily
played. If planning on using the Bluetooth audio input, make sure to verify the
Bluetooth functional range before finalizing a mounting location. Depending
on the construction of the TV, wall-box, building materials, etc, the range of
the internal Bluetooth receiver may be impacted.

AVA-Series Amplifiers 5
USING THE MINIAVR
HDMI  CONNECTING A TV OR OTHER HDMI AUDIO SOURCE
Connect the HDMI cable to the HDMI Port on the TV labeled HDMI (ARC or
eARC) and to the rear HDMI port of your AVA-Series Amplifiers labeled “ARC”. It
is very important that you connect to the ARC or eARC HDMI connection
on the TV. This enables the audio output of the TV through the HDMI
connection and enables CEC control between the TV and the AVA-Series
Amplifiers so that the TV remote control can control the mini-AVR without the
need for any programming.
TV SETTINGS
Most televisions will require changing a settings menu to disable their
internal speakers and enable the audio output through the HDMI ARC port
of the television. Some may even require adjustments to the HDMI control to
enable CEC operation. Please refer to the television owner’s manual for those
settings. For any HDMI ARC enabled product like the advanced AVA-Series
Amplifiers, you’ll need to make sure that these settings are configured on the
connected television:
AUDIO OUTPUT
Make sure the TV’s Audio Output is configured for the HDMI ARC or eARC
port that is connected to the amplifier
TV SPEAKERS DISABLED
Do not use an “Automatic” setting if you want to use audio sources other than
ARC when connected to your TV or your TVs internal speakers may turn on
when not desired.
CEC CONTROL ENABLED
Most TVs will have CEC control enabled by default. Using CEC
is recommended in order to allow your TV remote to control the
AVA-Series amplifier.
AUX
Connect any audio source to the stereo RCA AUX input on the
rear of your AVA-Series Amplifiers. The connected source may
be selected by using the included remote control and pressing
the input selection button on the top right of the remote control
until you hear the desired source.

6AVA-Series Amplifiers
USING THE MINIAVR
DIGITAL OPTICAL IN
Connect any digital audio source to the digital optical input on the rear of your
AVA-Series Amplifiers. The connected source may be selected by using the
included remote control and pressing the input selection button on the top
right of the remote control until you hear the desired source.
USING BLUETOOTH
Before using Bluetooth, your phone, tablet, or computer must be paired with
your AVA-Series Amplifiers.Pairing may be done by selecting the Pair button
on the remote control until the front panel LED on your AVA-Series Amplifiers
begins blinking blue. While blinking, the amplifier is in pairing mode and
can be found by searching for AVA3.1 or AVA2.1 from your phone, tablet, or
computer.
Once connected, you can use your phone’s volume control to go from zero up
to the current maximum volume of the AVA-Series Amplifiers. We recommend
setting your phone to its highest volume and then adjusting the AVA-Series
Amplifiers to the maximum desired level so that you can then easily control
the volume using your phone’s volume control.
Once your phone has been paired, you can connect and send audio to your
AVA-Series Amplifiers at any time by selecting “Bluetooth” as the active
source using the AVA remote control.
POWER CONNECTION
Once the source and loudspeaker connections have been made you can
connect the power cable to the rear of mini-AVR.
USING THE REMOTE CONTROL
To use the included remote control, make sure to connect the included IR
sensor to the “IR In” connection on the rear of the AVA-Series Amplifiers. All
infrared commands are received through this sensor.

AVA-Series Amplifiers 7
USING THE MINIAVR
FUNCTIONS AVAILABLE:
•
•
•
•
•
•
Volume +/-/Mute
Direct Input Select (Bluetooth, ARC (HDMI), Digital Optical (OPT), Line In
(Aux)
Audio Adjustments – Bass +/-, Treble +/-, Mega Bass On/O, Movie
Mode, Music Mode, Voice Mode (to enhance dialog)
Bluetooth Pairing Mode Activation (Pair)
Play/Pause
Skip Track Forward/Back
•Amplifier Power
TV CONTROL BUTTONS
If using the HDMI ARC input, there should be no need to use the TV infrared
commands from the remote control, but they are available for use when
connecting a TV to the amplifier’s digital or Line In input connection.
The included remote control is a multi-function
learning remote control. The top section of the
remote control is designed to learn several of the
most important TV commands from your TV remote.
To do this, press and hold the “Set” button in the top right of the remote
control for 10 seconds or until the light turns a solid bright red.
With the red light illuminated, press the button on the top of the remote that
you would like to teach, for example the TV Input “TV In” button. The red Set
button LED will blink fast, indicating it is ready to learn the IR command.
Place your TV remote end to end with the Russound AVA remote control so
that the front of both remote controls are within 1” (2.54 cm) of each other.
Press the button that you want to teach, in our example, the TV Input button
on your TV remote control until the red SET LED becomes solid again.
You may continue to teach other commands in any order by pressing the
next button you wish to teach on the top section of the AVA remote control
until the red Set button LED blinks fast, indicating it is ready to learn the IR
command for that button and continuing the process, button by button.
When you have taught all commands, press the Set button one more time

8
until the LED turns o.
Verify the correct programming by testing all of the learned buttons with
your TV. You can repeat the above steps to re-learn any particular button as
needed.
CREATING A . OR . AUDIO SYSTEM
By combining a Russound AVA3.1 with an AVA2.1 or any stereo amplifier, it is
possible to create a quick 5.1 surround (all stereo mode) system for any room.
Use a stereo 3.5mm to RCA cable (not included) to connect from the Line Out
of the AVA3.1 to the audio input of the AVA2.1 or other amplifier. When using
a Russound AVA2.1 as the additional amplifier, a second subwoofer can be
connected to the AVA2.1 subwoofer out to create up to a 5.2 stereo system.
Select Aux as the audio input on the AVA2.1. The AVA2.1 will play the audio
sent from the AVA3.1 to create the 5.1 or 5.2 system.
FRONT PANEL LED STATUS
The front panel LED will indicate the status of the AVA mini-AVR as indicated
AVA-Series Amplifiers
in this table.
LED COLOR
LED COLOR SELECTED SOURCE
White ARC (HDMI) input is selected
Green Optical input is selected
Blue Bluetooth input is selected
Cyan Analog input is selected
USING THE MINIAVR

AVA-Series Amplifiers 9
LED STATUS
3 Blinks IR command received
Fast Blink Volume has reached maximum or
minimum setting
Slow Blink Audio is muted
Blue (Blinking) Bluetooth pairing mode is active
Red (Solid) Standby mode
AUDIO DSP ADJUSTMENTS USING THE REMOTE CONTROL
MEGA BASS
This setting is recommended when there is no dedicated subwoofer. Pressing
this button toggles an increase in the bass levels by approximately 10% from
50-100Hz.
BASS +/
This is a broad bass change across the range of 80Hz to 500Hz by
approximately 1% for every button press, up to 10. When the limit is reached
in either direction, the front panel LED will blink quickly
TREBLE +/ 
This is a broad treble change across the range of 1kHz to 20kHz, by
approximately 1% for every button press, up to 10. When the limit is reached
in either direction, the front panel LED will blink quickly
RESET BUTTON
This button will reset all audio settings back to factory defaults.
VOICE DIALOG
This button will enable a high pass filter at 100Hz and a low pass filter at
12KHz to allow for more dialog detail and clarity. In this mode, you may also
customize the bass and treble or enable Mega Bass as desired.
USING THE MINIAVR

10
MOVIE
This button will enable a high pass filter at 35Hz, and a Box EQ at 240Hz
(-4dB) and 860Hz (-3dB) to allow for dynamic response in movies and films.
In this mode, you may also customize the bass and treble or enable Mega
Bass as desired. Movie mode is the default acoustic mode of the AVA-Series
amplifier.
MUSIC
This button will remove audio filters so that the EQ is flat from 20Hz to 20kHz
for clear, uncluttered detail in all musical genres. In this mode, you may also
customize the bass and treble or enable Mega Bass as desired.
Note: All changes to the audio settings will reset to defaults if the AVA is
AVA-Series Amplifiers
disconnected from AC power.
USING THE MINIAVR

Designedin
NewHampshire
Madein China
100-240VAC
50/60Hz 150W
4~8Ω

12 AVA-Series Amplifiers
SPECIFICATIONS
Model AVA2.1 AVA3.1
Number of Channels 2.1 3.1
Power Output - 4 ohm 50W /Channel, 1kHz 50W /Channel, 1kHz
Power Output - 8 ohm 25W /Channel, 1kHz 25W /Channel, 1kHz
20Hz to 20kHz +/-3dB at 1W output into
Freq Response 4 or 8 Ohms
20Hz to 20kHz +/-3dB at 1W output
into 4 or 8 Ohms
Input Sensitivity 1000mV for 50W at 1kHz, 4 Ohm 1000mV for 50W at 1kHz, 4 Ohm
Input Impedance >22k ohms Line Input >22k ohms Line Input
Signal to Noise Ratio , 4Ω >94dB A-weighted >93dB A-weighted
Signal to Noise Ratio , 8Ω >96dB A-weighted >97dB A-weighted
HDMI (ARC), Line In (RCA), Optical,
Inputs Bluetooth
HDMI (ARC), Line In (RCA), Optical,
Bluetooth
Bluetooth Version 5.0 5.0
Bluetooth Range Up to 100 feet (30m) Up to 100 feet (30m)
Remote Control Included Included
IR Input/Output 3.5mm 3.5mm
IR Sensor Included Yes Yes
Speaker Connectors Detachable Screw-down, up to Detachable Screw-down, up to 14AWG 14AWG
Line Out 3.5mm Stereo 3.5mm Stereo
Subwoofer Out RCA RCA
Operating Temperature 32°F to 104°F (0°C to 40°C) 32°F to 104°F (0°C to 40°C)
Altitude 0 to 9,843’ (3,000m) 0 to 9,843’ (3,000m)
Power Requirements - North Ameri-
can Model 100-120VAC, 60Hz (150W Max) 100-120VAC, 60Hz (150W Max)
Power Requirements - International
Model (-i) 220-240VAC, 50Hz (150W Max) 220-240VAC, 50Hz (150W Max)

AVA-Series Amplifiers 13
SAFETY
1. Read Instructions - All the safety and operating instructions should be read before
the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be retained for
future reference.
3. Heed Warnings - All warnings on the appliance in the operating instructions should
be adhered to.
4. Follow Instructions - All operating and user instructions should be followed.
5. Water and Moisture - The appliance should not be used near water; for example,
near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a
swimming pool. The apparatus shall not be exposed to dripping or splashing liquids
and no objects filled with liquids, such as vases, shall be placed on the apparatus.
Do not touch the appliance with wet hands. Do not handle the appliance or power
cord with wet or damp hands. If water or any other liquid enters the appliance
cabinet, take it to qualified service personnel for inspection.
6. Cleaning - The appliance should be cleaned only as recommended by the
manufacturer. From time to time you should wipe o the front and side panels and
the cabinet with a soft cloth. Do not use rough material, thinners, alcohol or other
chemical solvents or cloths since this may damage the finish or remove the panel
lettering.

14
7.
AVA-Series Amplifiers
Ventilation - The appliance should be situated so that its location or position does
not interfere with its proper ventilation. For example, the appliance should not
be situated on a bed, sofa, rug, or similar surface that may block the ventilation
openings, or placed in a built-in installation, such as a bookcase or cabinet that
may impede the flow of air through the ventilation openings. Place the unit in a
well-ventilated location, leaving at least 2 inches (5 cm) of clearance on all sides,
top and rear of unit for air flow. If ventilation is blocked, the unit may overheat and
malfunction.
8. Heat - The appliance should be situated away from heat sources such as radiators,
heat registers, stoves, or other appliances (including AVA-Series) that produce
heat.9. Grounding or Polarization - Precaution should be taken so that the grounding
or polarization means of an appliance is not defeated.
10. Power Cord Protection - Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, receptacles, and the point where they exit
from the appliance.
11. Power Sources - The appliance should be connected to a power supply only of the
type described in the operating instructions or as marked on the appliance.
12. Main Power Disconnect - The main power plug is used as the disconnect device
and shall remain readily operable. When installing the product, ensure that the
plug is easily accessible.
13. Non-Use Periods - The power cord of the appliance should be unplugged from the
outlet when left unused for a long period of time.
14. Attachments - Only use attachments/accessories specified by the manufacturer.
15. Location of the Mini-AVR - Do not mount this unit under a kitchen cabinet. Do not
expose the mini-AVR to direct sunlight or heating units as the mini-AVR internal
components’ temperature may rise and shorten the life of the components.
16. Avoid damp and dusty places.
17. Object and Liquid Entry - Care should be taken so that objects do not fall and
liquids are not spilled into the enclosure through the openings.
18. Servicing - The user should not attempt to service the appliance beyond that
described in the operating instructions. All other servicing should be referred to
qualified service personnel.
19. Damage Requiring Service - The appliance should be serviced by qualified service
personnel when: A. The power supply cord or the plug has been damaged; B.
Objects have fallen, liquid has been spilled into the appliance; C. The appliance
has been exposed to rain; or D. The appliance does not appear to operate
normally; or E. The appliance has been dropped or the enclosure is damaged.
SAFETY

AVA-Series Amplifiers 15
WARRANTY
LIMITED WARRANTY
The Russound AVA2.1 and AVA3.1 are guaranteed for two (2) years from the
date of purchase against all defects in materials and workmanship. During
this period Russound will replace any defective parts and correct any defect
in workmanship without charge for either parts or labor. For this warranty to
apply, the unit must be installed and used according to its written instruc-
tions. If service is necessary, it must be performed by Russound. Russound
assumes no responsibility for defects resulting from abuse or servicing per-
formed by an agency or person not specifically authorized in writing by Rus-
sound. Damage to or destruction of components due to improper use voids
the warranty. In these cases, the repair will be made at the owner’s expense.
Accidental damage and shipping damage are not considered defects under
the terms of the warranty. To return for repairs, the unit must be shipped to
a repair facility designated by Russound at the owner’s expense, along with
a Return Authorization number and documentation explaining the nature of
the service required. Any product returned without prior written permission
will be returned to sender. Russound sells products only through authorized
Dealers and Distributors to ensure that customers obtain proper support and
service. Any Russound product purchased from an unauthorized dealer or
other source, including retailers, mail order sellers and online sellers will not
be honored or serviced under existing Russound warranty policy. Any sale of
products by an unauthorized source or other manner not authorized by Rus-
sound shall void the warranty on the applicable product.
WARRANTY ADDRESS
Russound
Attn: RA# (Insert your RA number here)
1955 Wehrle Dr
Williamsville NY 14221
email: [e-mail]

FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following twoconditions:(1) This device may not cause harmful interference, and
(2) this device must accept any interference receivedincluding interference that
This equipment has been tested and found to comply with the limits for a
Class B digital device,pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turningthe equipment off and on,
the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which
the receiver isconnected.
-- Consult the dealer or an experienced radio/TV technician for help.
may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator & your body.

IC Warning
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference including interference that may
cause undesired operation of the device
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si lebrouillage est susceptible d’en compromettre le fonctionnement.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body. This
transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Cet équipement est conforme aux limites d'exposition au rayonnement ISED
établies pour un environnement non contrôlé Cet équipement doit être installé et
utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.

©2023 Russound/FMP, Inc. All rights reserved.
All trademarks are the property of their respective owners.
Specifications are subject to change without notice REV5