RYCO RYCS10 User manual

CONNECTING PARTNERSHIPS
OPERATION MANUAL
RYCS10 Cut-Off Saw

RYCO CLEAN Hand Launcher Kit
The RYCO CLEAN Kit is an easy to use, low-cost solution to
eliminate hydraulic contamination from the inside of hose,
tube, and pipe. It is designed to clean the internal surfaces of
hose, tube, and pipe eectively and eciently. It comprises of
a pneumatic hand launcher, an adaptor ring, and a range of
specially designed nozzles to accommodate dierent sizes of
hose, tube, and pipe.
The optimum air input pressure range for the RYCO CLEAN
Hand Launcher to operate eectively is between 87 psi (6
bar) and 110 psi (7,5 bar).
Includes: Features & Benefits:
1 x Pneumatic hand held Launcher • Light-weight ergonomic design
1 x Adaptor ring • Easy to use and operate
1 x Tough case • Pneumatic pistol-grip Launcher
10 x nozzle to suit ¼”– 2” ID hose, tube and pipe • Multiple nozzle sizes to suit a range of hoses,
tubes and pipes
RYCO CLEAN Hand Launcher Kit
Part Number: RCPS-HLK
• Heavy-duty carrying case for added protection
CONNECTING PARTNERSHIPS
CLEAN KIT
Contact your nearest RYCO representatives for more information about the RYCO CLEAN Hand Launcher Kit.
The ideal
accessory for your
RYCO RYCS10
Cut-O Saw

RYCO RYCS10 CUT-OFF SAW iii
RYCS10 CUTOFF SAWRYCS10 CUTOFF SAW
1. GENERAL INFORMATION ........................................................................................................................................ 1
2. WARRANTY INFORMATION ..................................................................................................................................... 1
3. WARRANTY CLAIMS................................................................................................................................................ 2
4. LIABILITY INFORMATION ........................................................................................................................................ 2
5. WARNINGS AND SAFETY INSTRUCTIONS................................................................................................................ 2
6. MACHINE LAYOUT................................................................................................................................................... 3
7. DANGER ZONES AND WARNING LABELS ................................................................................................................ 4
8. INSTALLATION........................................................................................................................................................ 5
9. COMMISSIONING..................................................................................................................................................... 5
10. USAGE BY OPERATORS ........................................................................................................................................... 6
11. SAFE OPERATION REQUIREMENTS ......................................................................................................................... 6
12. CONDITIONS OF USAGE .......................................................................................................................................... 6
13. OPERATING PROCEDURE ........................................................................................................................................ 7
14. EMERGENCY STOP BUTTON.................................................................................................................................... 8
15. SPECIFICATIONS .................................................................................................................................................... 8
16. GENERAL NOTICE ON MAINTENANCE AND INSPECTION.................................................................................... 9-10
17. BLADE CHANGING PROCEDURE............................................................................................................................ 11
18. SAFE REMOVAL OF THE WASTE COLLECTION TRAY .............................................................................................. 12
19. SAFE TRANSPORTATION....................................................................................................................................... 12
20. SAFE MACHINE STORAGE ..................................................................................................................................... 12
21. CORRECT DISPOSAL OF PACKAGING..................................................................................................................... 12
We reserve the right to alter the design or discontinue any of the company’s products or services without notice. Whilst every eort
has been made to ensure the accuracy of the information contained in this publication, our Company Policy of continual research
and product development necessitates changes and renements which may not be reected in these pages. If in doubt, please
contact your nearest RYCO sales oce.
Copyright 2022. E&OE. All rights reserved. This Operating and Maintenance Manual may NOT be reproduced, in whole or in parts,
by any means, without the written approval of this company’s directors.
RYCO RYCS10 CUT-OFF SAW

RYCO RYCS10 CUT-OFF SAW
1
RYCO RYCS10 CUTOFF SAW
1. GENERAL INFORMATION
Do not unpack nor operate the RYCS10 Cut-O Saw until you have thoroughly read and understood the contents of this operation
manual.
This operation manual:
• Should be stored and kept in a good condition for future use
• Provides all necessary information relating to the safe operation and usage of the RYCS10 cut-o saw.
The information contained within this operation manual is for operators who can safely operate the RYCS10 Cut-O Saw without being
a risk to:
• Themselves
• Other persons
• Property
• The machine; or,
• The environment.
Also, all operators must have a proven understanding of:
• Performing machine inspections; and,
• Safe hose making practices and procedures in compliance with:
–This operation manual
–Appropriate Work Safe legislation within their location; and,
–RYCO Hydraulics’ Safe Work Instructions.
Contact RYCO Hydraulics or your nearest authorised RYCO distributor for a replacement operation manual or if additional information on
the RYCS10 Cut-O Saw is required.
The RYCS10 Cut-O Saw has been designed:
• For the safe, clean, and ecient cutting of textile or wire braided, suction, and multi-spiralled hydraulic hoses
• To only cut hydraulic hoses of maximum size and construction as specied herein; and,
• For use in workshop and/or mobile service van environments.
2. WARRANTY INFORMATION
These products are supplied in accordance with “RTS” (RYCO Terms of Sale”. The warranty on the RYCS10 Cut-O Saw is for one (1) calendar
year from date of purchase and only under the condition that the instructions contained within this operation manual have been strictly
adhered to.
The warranty on the RYCS10 Cut-O Saw covers:
• Any defect materials or parts
• Any faulty workmanship in its manufacture or assembly; and,
• The cost of repairs and the replacement of any defect parts, including labour.
The warranty on the RYCS10 Cut-O Saw does not cover any:
• Improper or incorrect use
• Wear and tear through normal or regular use
• Travel, shipment, or time costs incurred; or any,
• Lost income due to this machine not working.
GENERAL INFORMATION

RYCO RYCS10 CUT-OFF SAW 2
WARRANTY AND SAFETY INSTRUCTIONS
3. WARRANTY CLAIMS
Contact RYCO Hydraulics for any warranty claims.
4. LIABILITY INFORMATION
RYCO Hydraulics is not liable for any injury or damage to persons, machinery, or property due to any:
• Improper use
• Prohibited modications made to the RYCS10 Cut-O Saw; or,
• Misinterpreting the contents of this operation manual.
5. WARNINGS AND SAFETY INSTRUCTIONS
Establishing a safe working environment and safe working practices is common sense.
Operators are to read the following before operation:
• Extreme caution must be exercised when operating the RYCS10 Cut-O Saw to avoid damage to the machine or its Steel Cut-O Blade,
or personal injury
• Disconnect electrical power supply to the RYCS10 Cut-O Saw before performing any inspection, maintenance, or service tasks. Secure a
Safety Hazard “Do Not Operate” tag to the equipment
• Make sure the RYCS10 Cut-O Saw is securely mounted and in serviceable condition before use
• Regularly inspect the Steel Cut-O Blade for nicks, cracks, distortion, missing sections from the cutting edge, or other damage; and
replace Blade immediately if damaged
• Wear eye, ear and hand protection when using the RYCS10 Cut-O Saw
• Loose tting clothing and jewellery should not be worn near the RYCS10 Cut-O Saw
• Always work in a clean, dry, well-lit workspace with adequate ventilation for removal of smoke and fumes
• Keep appendages clear of moving parts and cutting blades, and hands well clear of cutting zone
• If the cutting hose has been used in service any uid that has been in the hose may cause toxic fumes when cut. Wear breathing
protection when necessary. Also, when ignited some hydraulic uids can explode and / or cause re – therefore, ensure all adequate
safety measures are taken
• Only switch ON the Cut-O Saw immediately before use; and switch OFF the Cut-O Saw immediately after cutting is complete
• The hose ends may be hot after cutting, and hot fragments may emit from the cutting zone when cutting. Be careful to avoid burns
• Electricity used to drive the RYCS10 Cut-O Saw motor can create sparks that may cause re, explosion, or electrocution
• Do not attempt to cut larger sizes of hose than those specied within this Operations Manual
• Do not smoke in the vicinity when cutting RYCO RTH1 Teon hose or similar hoses, because fumes created may mix with tobacco smoke
and become toxic
• Do not use the RYCS10 Cut-O Saw to cut materials other than hose
• Do not operate the RYCS10 Cut-O Saw with any Safety Guards removed
• Before commencing any cut ensure the blade has reached its full speed; and,
• When using:
–Mains Voltage versions: do not use extension cords as low voltage can cause damage to the saw motor
–Portable power sources: ensure power can be consistently delivered as low voltage can cause damage to the saw motor

6. MACHINE LAYOUT
RYCO RYCS10 CUT-OFF SAW
3
RYCO RYCS10 CUTOFF SAW
MACHINE LAYOUT
Blade (behind safety cover)
Hose pusher
Electrical Box
Power ON/OFF switch
Left Hose Support Pin
Waste Collection Tray Right Hose Support Pin
Operating Lever
Figure 1 – Machine Layout
Emergency Stop Button

RYCO RYCS10 CUT-OFF SAW 4
7. DANGER ZONES AND WARNING LABELS
DANGER ZONES AND WARNING LABELS
Always wear personal protective
equipment during saw operation.
If the RYCS10 Cut-O Saw is making any abnormal sound or
movement, press the emergency stop immediately.
Do not insert hands into the cutting point while
the RYCS10 Cut-O Saw is in operation.
Before cleaning the Waste
Collection Tray, disconnect all
power from the RYCS10 Cut-O
saw.
Always wear personal protective equipment during saw operation.
If the RYCS10 Cut-O Saw is making any abnormal sound or movement, press the emergency stop
immediately.
Do not insert hands into the cutting point while the RYCS10 Cut-O Saw is in operation.
Before cleaning the Waste Collection Tray, disconnect all power from the RYCS10 Cut-O saw.
Figure 2 – Danger Zones

RYCO RYCS10 CUT-OFF SAW
5
8. INSTALLATION
Before installing and using the RYCS10 Cut-O Saw, RYCO recommends thoroughly:
• Reading the contents of this operation manual
• Ensure all cords are new, intact, and suitable for the relevant power source; and,
• Inspecting the machine to ensure it displays:
–2 x RYCO (logo) Labels
–1 x RYCS10 (logo) Label
–2 x Emergency Stop Labels
–1 x Warning Label
–1 x Hearing and Eye protection Label; and,
–1 x Caution Label.
The RYCS10 Cut-O Saw must:
• Be installed on a rm, stable, and level work surface with adequate clearance for safe working
• Be secured to the work surface using suitable M8 size bolts, washers, and nuts fastened through the mounting holes in the Cut-O Saw
base as dimensioned in the gure below; and,
• Have clear, easy to access surroundings to allow operators to conduct any approved or suitable cleaning or maintenance.
Figure 3 – RYCS10 Mounting Holes
9. COMMISSIONING
The RYCS10 Cut-O Saw is shipped fully assembled and wired, ready for use.
After removing from its secure wooden box packaging, the RYCS10 Cut-O Saw only requires mounting to the work surface, and
connection of the electrical plug to the appropriate mains power.
The RYCS10 Cut-O Saw is intended for use in mobile service vehicles and/or workshop environments mounted to the work surface.
Prior to use, operators must check:
• All fasteners and the nut securing the Steel Cut-O Blade to the shaft to ensure that it has not become loose in transit
• To ensure that no damage has occurred in transit
• The Steel Cut-O Saw Blade is mounted centrally with no axial or radial run out, and that it rotates easily; and,
• Ensure that the direction of rotation is so that when viewed from the front Operating Handle side of the Cut-O Saw, the Cut-O Saw
Blade rotates in a direction from the top of saw to bottom of saw.
INSTALLATION AND COMMISSIONING
RYCO RYCS10 CUTOFF SAW

RYCO RYCS10 CUT-OFF SAW 6
10. USAGE BY OPERATORS
The RYCS10 Cut-O Saw should only be used by persons who are familiar with the correct and safe usage of this machine as outlined within
the contents of this operations manual.
To avoid personal injury, all hands, feet, loose clothing, jewellery, and all other body parts must be kept well away from the RYCS10 Cut-O
Saw during operation.
Do not exceed the operational rating of the RYCS10 Cut-O Saw as overloading will cause equipment failure and potential injury.
11. SAFE OPERATION REQUIREMENTS
Before safely operating the RYCS10 Cut-O Saw, operators must:
• Read and understand the contents of this operation manual
• Be fully trained in its operation
• Be fully competent in its operation
• Be fully alert
• Not be fatigued or aected by medication, alcohol, or drugs; and,
• Ensure the working area is well properly lit and ventilated.
12. CONDITIONS OF USAGE
The RYCS10 Cut-O Saw must be installed and only used within the following conditions:
• Supply voltage: 0.9 - 1.1 nominal supply voltage
• Source frequency: 0.99 - 1.01 nominal frequency
• Ambient temperature: 5°C - 40°C (40°F - 104°F)
• Altitude: shall be at altitudes up to 1000m above sea level
• Relative humidity: not exceed 50% at 40°C (104°F); and,
• Atmosphere: free from excessive dust, acid fumes, corrosive gases, and salt.
The RYCS10 Cut-O Saw should not be exposed to any:
• Direct sunlight, heat rays or ames
• Damp or wet conditions, including being exposed to rain and/or moisture
• Explosive environment
• Equipment with a temperature above 50°C (122°F); or any,
• Area where children, animals, and/or other adults are in (close) proximity.
The RYCS10 Cut-O Saw should not:
• Be modied in a way; nor,
• Be used for any application other than for which it was intended as listed within the contents of this operations manual.
For optimum performance, the RYCS10 Cut-O Saw must be kept and in a continually clean and safe working order.
USAGE GUIDELINES

RYCO RYCS10 CUT-OFF SAW
7
13. OPERATING PROCEDURE
1. Position the Hose Support Pins to suit the hose size and type to be cut, as shown in the diagram below. These positions are a guide
only, dierent Hose Series may require the Hose Support Pins to be moved inwards or outwards to achieve a square cut.
NOTE: the Hose Support Pins on either side of the blade must be an equal distance from the blade.
-06
and
below
-06
and
below
-08
-10
-12
-08
-10
-12
-16
-20
-24
-16
-20
-24
The Hose Support Pins, together with the Support Notch at the bottom of the Operating Lever, remove the need for hand contact on
the hose during cutting.
Figure 4 – RYCS10 Hose Support Pin locations
2. Move the Operating Lever into the back position
3. Mark the hose cut location on the hose, then position the hose to be cut so that:
i) it is lying at on the bed of the Saw
ii) it is in contact with both Hose Support Pins; and,
iii) the cut position marked on the hose is aligned with the blade guard slot
NOTE: Do not attempt to cut or trim short pieces from hose. The hose must be in contact with both Hose Support Pins during the entire
cutting cycle.
4. Start the Cut-O Saw rotation by pressing the Power ON/OFF Switch at the top of the Operating Lever using your thumb.
NOTE: The RYCS10 Cut-O Saw motor operates only while the Power ON/OFF Switch is depressed.
OPERATING PROCEDURE
RYCO RYCS10 CUTOFF SAW

RYCO RYCS10 CUT-OFF SAW 8
EMERGENCY STOP BUTTON
5. Move the Operating Lever towards the hose ensuring that the hose is located against the Hose Support Pins
6. Ensure the hose is in the Support Notch at the bottom of the Operating Lever. The Blade Safety Guard moves with the Operating Lever
to expose the Blade to enable cutting to commence.
7. Continue to move the Operating Lever forward until the hose contacts the Steel Cut-O Blade.
8. Maintain an even pushing force on the Operating Lever
NOTE: Do not push too forcefully; this may be indicated by the motor labouring or decreasing in RPM or stalling.
Excessive pushing force can damage the Steel Cut-O Blade or cause the hose to become distorted/burnt. It may be necessary to pause
cutting for several seconds to allow the blade to cool suciently before continuing the cut.
9. When cutting is complete, release the Power ON/OFF Switch and move the Operating Lever to the fully back position.
10. Carefully remove the cut hose from the Saw Bed area.
11. Inspect the hose to ensure that the cut is clean and square at 90° to axis of hose.
Never leave the RYCS10 Cut-O Saw machine powered on or running while unattended. To prevent any unintentional activation, ensure
the RYCS10 Cut-O Saw is electrically isolated at the power source, and the EMERGENCY STOP button is depressed.
14. EMERGENCY STOP BUTTON
Should electrical power to the RYCS10 Cut-O Saw motor need to be cut immediately in the
event of a dangerous/unsafe or emergency situation, the operator must press the Emergency
Stop button.
Emergency or unsafe situations can include (but are not limited to) overheating of work-piece or
saw components, the hose or any other item (i.e., clothing, body parts, jewellery, etc.) becoming
jammed or caught against the blade, or any other potentially unsafe circumstances as deemed by
the personnel using the equipment.
The Emergency Stop is located on the top of the RYCS10 Cut-O Saw (see Figure 1 – Machine
Layout) and is identied by two red Emergency Stop labels (see Figure 2 – Danger Zones and
Warning Labels)
Once the Emergency Stop button has been pressed, all power to the RYCS10 Cut-O Saw must be
disconnected by unplugging the machine from its power source (i.e., power socket).
15. SPECIFICATIONS
RYCS10  SPECIFICATIONS
ELECTRICAL PHYSICAL DIMENSIONS
PART NUMBER VOLTAGE PHASE MOTOR POWER SPEED WIDTH DEPTH HEIGHT WEIGHT
kW hp RPM mm inch mm inch mm inch kg lb
RYCS10-1-240 240 11.5 2.0 2850 610 24.0 404 15.9 450 17.7 45 99
RYCS10  TECHNICAL INFORMATION
NOMINAL CUTTING CAPACITY
PART NUMBER BLADE SIZE WIRE BRAID SUCTION 4 SPIRAL 6 SPIRAL MAX HOSE O.D.
mm inch Dash inch Dash inch Dash inch Dash inch mm inch
RYCS10-1-240 250 10 -24 1.1/2 -24 1.1/2 -20 1.1/4 -20 1.1/4 55 2.1/8

RYCO RYCS10 CUT-OFF SAW
9
MAINTENANCE AND INSPECTION
Dimensions in mm
Figure 5 – RYCS10 basic dimensions
Notes: Illustrations are not to scale and are indicative only.
Figure 6 – RYCS10-1-240 Electrical Schematic
RYCO RYCS10 CUTOFF SAW

RYCO RYCS10 CUT-OFF SAW 10
MAINTENANCE AND INSPECTION
16. GENERAL NOTICE ON MAINTENANCE AND INSPECTION
To keep the accuracy and maintain the best condition of the RYCS10 Cut-O Saw, correctly maintaining and inspecting this machine is
important.
Machine power must be o before any maintenance is carried out while all electrical maintenance must be conducted by a qualied
technician.
Other important notes on maintenance:
• Disconnect the electrical power supply from the Cut-O Saw and depress the EMERGENCY STOP button before performing any
inspection, maintenance, or service tasks. Secure a Safety Hazard “Do Not Operate” tag and a maintenance lockout device to the
equipment
• Regularly check all fasteners, and the nut securing the Blade to the shaft, to ensure that they have not become loose
• Lubrication oil should be added in a timely and correct fashion
• Prior to use, inspect the Steel Cut-O Saw Blade for nicks, cracks, distortion, missing sections from the cutting edge, or other damage;
and replace Blade immediately if damaged
• Inspect to ensure that the Steel Cut-O Saw Blade is mounted centrally, with no axial or radial run out. Also inspect for any vibrations
when the Saw is running; and,
• To assist with breaking in and conditioning the blade for long life, feed the blade slowly through a medium size hose for the rst ve
cuts
• Daily maintenance of the RYCS10 Cut-O Saw should include:
–Checking the control box, electricity door and components
–Clean the worktable and electrical box cover by a clean cloth
–Check to ensure the RYCS10 Cut-O Saw is securely mounted and in serviceable condition
–Clean the working environment around the RYCS10 Cut-O Saw
–Regularly remove any build-up of cutting debris; and,
–Lubrication oil should be added in a correct fashion where required.
• Weekly maintenance of the RYCS10 Cut-O Saw should include:
–Always check for any abnormal sound or vibration when operation
–Check for damage or deterioration to the external electric cable
–Check warning labelling is clean or not. If they become unclear or disappear, contact your nearest RYCO representatives for
replacements; and,
–Check safety cover for any damage.

RYCO RYCS10 CUT-OFF SAW
11
The following are indications that the Cut-O Blade may require sharpening:
• Tube of hose separated from the reinforcement
• Wire reinforcement changed colour to blue due to excessive heat
• Wire reinforcement not cleanly cut
• Excessive force required for cutting; and,
• Blade cutting edge turned blue from heat or the blade being warped.
17. BLADE CHANGING PROCEDURE
Figure 7 – RYCS10 blade change schematic
1. Disconnect the electrical power supply from the Cut-O Saw. Secure a Safety Hazard “Do Not Operate” tag to the equipment.
2. Wearing safety gloves remove screws from left side saw blade shroud - E.
3. Remove blade shroud from saw
4. Using appropriately sized spanner hold blade shaft D, loosen the nut A holding the Steel Cut-O Saw Blade, and remove the Blade.
Take extreme care when handling Steel Cut-O Saw Blades to avoid personal injury.
5. When blade is removed ensure hub and shaft are clean and free from and debris.
6. Replacement is in the reverse order to removal, ensure blade is installed straight and true. Note the direction of rotation of the blade
and the correct direction of the teeth. Inspect all components to ensure there is no wear or damage; replace as necessary. Ensure that
the nut holding the Blade is tightened to correct torque.
7. Securely re-install left side blade shroud.
8. Remove Safety Hazard “Do Not Operate” tag.
9. Reconnect the electrical power supply to the RYCS10 Cut-O Saw.
10. Inspect to ensure that the Cut-O Saw Blade is mounted centrally, with no axial or radial run out. Also inspect for any vibrations. If there
is any run out or vibrations, immediately turn o the Cut-O Saw and repeat Steps 1 to 9.
RYCO RYCS10 CUTOFF SAW
BLADE CHANGING PROCEDURE
REPLACEMENT PART NUMBER BLADE SIZE
mm inch
RYCSW10 250 10

18. SAFE REMOVAL OF THE WASTE COLLECTION TRAY
Remove any excess hose cutting waste from the Waste Collection Tray of the RYCS10 Cut-O Saw by following the procedure below:
1. Ensure all power to the RYCS10 Cut-O Saw is disconnected from its
source.
2. Ensure the EMERGENCY STOP button is depressed.
3. Unscrew the black screw until completely removed
4. Remove and empty the Waste Collection Compartment (see direction
of arrow).
5. Ensure all waste is correctly disposed in line with local environmental
regulations.
6. Insert the Waste Collection Compartment back into the RYCS10 Cut-O
Saw before re-tightening the black screw.
19. SAFE TRANSPORTATION
The RYCS10 Cut-O Saw should be transported via its secure wooden packing box tted with carry slings whilst adhering to all
Occupational, Health, and Safety (i.e., OH&S) regulations.
After unpacking, and due to its net weight of 45kg, the RYCS10 Cut-O Saw should only be lifted using an approved, appropriately rated
lifting sling.
20. SAFE MACHINE STORAGE
If not be operated for long periods, the RYCS10 Cut-O Saw should be:
• Stored in its secure wooden packing box
• Stored in an environment free of dust, exposed sunlight, and moisture; and,
• Have all power fully disconnected.
21. CORRECT DISPOSAL OF PACKAGING
Check local environmental regulations before disposing of any packing or shipment materials, including investigating opportunities to
avoid disposal within landll.
RYCO RYCS10 CUT-OFF SAW 12
MAINTENANCE AND INSPECTION
Figure 8 – Waste Collection Tray

RYCO RYCS10 CUT-OFF SAW
13
TECHNICAL DATA
SCAN HERE FOR MORE
CONTACT INFORMATION
AUSTRALIA [phone]
RYCO GLOBAL HEAD OFFICE  MELBOURNE AUSTRALIA
99 Calarco Drive, Derrimut, VIC 3026
BRISBANE
97 Northlink Place,
Northgate, QLD 4013
PERTH
47 Tacoma Circuit,
Canning Vale, WA 6155
ADELAIDE
BL Shipway & Co.
217 Richmond Road,
Richmond, SA 5033
NEWCASTLE
14 Ironbark Close,
Warabrook, NSW 2304
NEW ZEALAND [phone]
AUCKLAND
4 Autumn Place, Penrose, Auckland 1061
USA & CANADA [phone]
USA HEAD OFFICE  HOUSTON TEXAS
1616 Greens Road, Houston, Texas 77032
CALIFORNIA
1150 Valencia Avenue,
Tustin, California 92780
ONTARIO
32 Airpark Place, Guelph,
Ontario, Canada N1L 1B2
IOWA
1007 West 10th Street,
Pella, Iowa 50219
CHINA [phone]
DALIAN
38 Ying Ri Road, Ying Cheng Zi Industrial Zone,
Gan Jing Zi District, Dalian 116036
MALAYSIA [phone]
PENANG
Plot 207 Kuala Ketil Ind. Estate, Kuala Ketil, Kedah 09300
SOUTH AFRICA [phone]
JOHANNESBURG
340 Roan Crescent, Corporate Park, North Midrand 1685
EUROPE [phone]
ITALY
Manuli Rubber Industries S.p.A.
Via L. Bizzarri, 19 - 40012 Calderara di Reno (Bologna), Italy
AUSTRALIA 133•24•7
NEW SOUTH WALES QUEENSLAND SOUTH AUSTRALIA
Bellingen
Batemans Bay
Casino
Dubbo
Goulburn
Ingleburn
Mascot
Newcastle
Penrith
Wallerawang
Wetherill Park
Brisbane
Blackwater
Charter Towers
Dalby
Emerald
Fraser Coast
Northside
Cowell
North Adelaide
Richmond
Roxby Downs
Whyalla
VICTORIA WESTERN AUSTRALIA NORTHERN TERRITORY
Bendigo
Carrum Downs
Melbourne
Kalgoorlie
Karratha
Newman
Port Hedland
Wangara
Darwin
NEW ZEALAND 0800•111•24•7
NORTH ISLAND SOUTH ISLAND
Auckland
Gisborne
Hawkes Bay
Hamilton
Masterton
Northwest
Otorohanga
Palmerston North
Pukekohe
Taupo
Waikato
Wellington
Whakatane
Whangarei
Christchurch
Dunedin
Invercargill
Nelson
Temuka
USA & CANADA +1 844•700•0247
TEXAS
Houston
RYCO LOCATIONS RYCO 24•7 SERVICE CENTRES
* Specifications correct at time of publication | All Rights Reserved | Printed in Australia | Copyright: February 2022 | Released: February 2022