Rydeen MV436S User manual

Owner’s Manual MV436S
High Brightness Rearview Mirror
with Auto Brightness Control
V1.0

WARNINGS
THE FOLLOWING INSTRUCTIONS ARE INTENDED FOR AUTHORIZED
RYDEEN SYSTEMS INSTALLERS ONLY.
PROFESSIONAL INSTALLATION BY AUTHORIZED RYDEEN RETAILER
REQUIRED TO BE COVERED UNDER WARRANTY.
Dropping your MV436S unit or subjecting it to excessive shock and vibrations as
this may cause it to malfunction and is not covered by warranty.
The MV436S unit IS NOT WATERPROOF. Avoid exposing it to rain or other
forms of excessive moisture. Water damage is not covered under the
warranty.
1. Installation
1) Remove existing mirror from vehicle.
2) If existing mirror tab is D-tab style mount MV436S mirror to windshield and
go to step 3. If original mirror is not D-tab style or headliner mount go to step
2a.
2a) Locate the supplied D-tab and the rearview mirror adhesive and install on
windshield as per adhesive instructions.
Note: DO NOT ATTEMPT TO REMOVE THE EXISTING TAB AS DAMAGE TO THE
WINDSHIELD MAY OCCUR
3) Remove the knee bolster on the driver side as well as the A-pillar cover (it may
also be necessary to remove the sun visor and maybe even the overhead
console in order to freely route the power harness from the knee bolster to the
mirror connector).
4) Connect the power harness to the mirror and use supplied mirror harness wire
cover in order to neatly route the cable up the windshield to the headliner.
5) Reassemble all above covers and make connections at knee bolster.
2. Wiring
RED- 12V+ Ignition
Black- Chassis Ground
Green- Not Used
VIDEO Camera RCA- Video input for camera (priority). The circuit switches
automatically when video is sensed by powering up the reverse camera
VIDEO IN RCA- AUX Video input (DVD, MP4 etc.) This circuit is secondary and so it will
be over written when Camera video is sensed.
1) Connect the camera’s 12V and GND wire to reverse tail lamp.
2) Connect the camera’s RCA to the mirror’s Camera input
3) Connect the MV436S 12V+ wire (RED) to the camera’s “reverse trigger output”
(RED) near the RCA
4) Connect the MV436S ground wire (BLACK) to chassis GND
Alternative wiring method for NOT having
the GREEN light ON all the time
Do not use this method if Video 1 & Backup Camera input are in use

3. Setup
1) Turn Ignition ON
2) If AUX video 1 source is connected (turn video source ON then press PWR
button on mirror and the image should appear on screen)
3) Shift vehicle into reverse, the camera image will appear on the screen
4) Shift vehicle out of reverse and the camera image will disappear and go back to
its previous stage
5) The white window on the left side of the power button is the photo sensor to activate
the monitor self-dimming/auto-brightness.
4. Power Button Operation
CAMERA input mode: Adjust brightness of screen
VIDEO 1 input mode: Turns ON and OFF LCD
5. Removable Mount Structure
MV436S is equipped with the removable mounting stem structure,
which allows to exchange with the following available ball joint
mounting stems.
6. Trouble Shooting
Q: The Green LED never turns ON and I do not get a picture?
A: Test to confirm that (+ & -) are connected properly and fuse is good.
Q: The Green LED is ON but I do not see any picture?
A: Make sure that the video RCA’s are connected properly and that the camera is
powered up properly as per camera instructions.
Q: The Green LED is always ON?
A: Follow the “Alternative installation method”
Q: The image on the mirror is opposite (left is right and right is left) what is wrong?
A: The White jumper on the camera harness is connected (should be cut in half).
Q: I do NOT like the parking lines, how can I turn them OFF?
A: Connect the Green jumper at the camera harness to turn the parking line feature
OFF.
7. Technical Support Contact Info
If you have other questions about the RYDEEN products, please contact your retailer
or Technical Support:
Telephone: [phone] (within USA only)
Email: [email protected]
Web Address: www.rydeenmobile.com

One Year Limited Warranty
Rydeen North America Inc. (a manufacturer of “RYDEEN" products) warrants this product
(Parking Sensor Systems) only to the original purchaser as described by the following:
Warranty Period
Rydeen warrants this product for a period of one (1) year from the original purchase date.
Warranty Coverage
This warranty covers all defects in material and workmanship except as specified below.
1. Installation by anyone other than an authorized RYDEEN retailer voids the warranty.
2. Any products distributed outside of the USA by Rydeen North America Inc. (RYDEEN) or
which is not purchased in the USA or Canada unless the product is purchased through the
USA Military Exchange Service.
3. Any product(s) which are purchased from an unauthorized retailer (in store or online).
4. Any products in which the serial number label or the model number label are removed,
torn, modified or replicated.
5. Any damage defects or malfunctions resulting from any of following:
a) When defect occurs during shipment of product (freight carrier's responsibility).
b) Installation or removal of product.
c) Accidents, act of nature, misuse, abuse, neglect, unauthorized product
modification or failure to follow product owner's manual instructions.
d) Any repair or attempt to repair without RYDEEN authorization.
e) Any other cause which is not related to product defect.
f) Any cosmetic damages due to normal wear and tear.
g) Any consumable items (such as fuse or batteries).
If any problems develop with your RYDEEN products during or after the Limited Warranty
Period, or if you have any questions regarding the operation or installation of the product, you
should contact your RYDEEN retailer. If the problem or your question is not handled to your
satisfaction, please contact Rydeen Customer Service Department at 1-877-777-8811 (within
the USA only) Monday - Friday between 9:00 AM to 4:00 PM Pacific Standard Time or visit
www.rydeenmobile.com.
www.rydeenmobile.com
Rydeen North America Inc.
dba Rydeen Mobile Electronics
2701 Plaza Del Amo, Suite 705, Torrance, California 90503 USA
Phone: [phone] Fax: [phone]
Copyright © 2019 Rydeen North America Inc. All Rights Reserved.
These materials are protected by copyright law and international treaties. Any unauthorized use, reproduction or distribution of these materials, or any portion
herein, will result in severe civil and criminal penalties and fines. Violators will be prosecuted to the fullest extent of the law.