Ryman cc12 User manual

INSTRUCTION MANUAL
CROSS CUT SHREDDER
cc12
Please Read the Following lnstructions Carefully before Use, and Keep for Future reference.
http ://www. rvman. co. u k
Ryman Ltd, CW1 6NA.

A WARNING
Please keep children away from
f-fr31 this shredder.
td.d I
ld&J The sharp blade inside the
shredder may harm children.
Please keep your hair away from
the shredder.
^ Also keep ties, necklace & hair
nR \ away from the shredder, as it may
\tV cause personal injury. lf they are
taken into the shredder, please
turn the power off immediatelv.
Please keep your hands out of the
paper entry.
/Sr\ The sharp blade inside the
\5/ shredder may cause injury.
lf smoke or abnormal smells
come from the shredder,
I ,fi I Please stop using it immediatety
tl-i-)'l and remove the plug from the
socket.
IMPORTANT SAFETY INFORMATION :
1. Read through these operating instructions carefully and completely before using
the machine for the first time.
2. The incorrect operation may cause personal injury or damage property.
3. Place the machine on a flat and dry surface, so that it is freely accessible from all
sides.
4. Do not use outdoors.
5. Please note the warnings printed on the shredder.
6. Do not pour or spill any liquid into or on the machine.
7. Please do not spray any flammable gas or oil onto the shreddel as it may cause a
fire.
Keep out the reach of children.
This appliance is not intended for use by persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Do not cover or place any object on top of the shredder.
Do not operate the appliance with a damaged cord or plug.
Please do not open the shredder unit or try to repair it. Repairs must only be
executed by a qualified tradesperson.
13. Do not operate the appliance if it has been dropped or is damaged in any manner.
14. Do not use the appliance for the other than the intended use.
15. Do not leave the shredder unattended while it is switched on.
16. Do not use near any combustible source, or in a damp or wet environment.
17. The shredder should be used close to the plug socket as the plug socket ouflet
should be accessible.
18. Please use the shredder with the correct power supply.
8.
9.
10.
11.
12.

Additional lmportant lnformation :
1. The shredder is a paper shredder; please do not shred film, oHp pouches,
lamination pouches, adhesive stickers, cloth or plastic as this will damage the
shredder.
2. This appliance is intended for small home office use only. lt is recommended to
switch off the machine for 30mins, after approx 2mins of use.
3. Always unplug the appliance when emptying the wast,e bin or when not in use.
4. Do not insert any metal objects into the machine.
OPERATIONS
W
Setup:
1. Remove the shredder from the outer carton.
2. Place the shredder head onto the basket. lf the shredder head does not make complete
contact with the basket, then the device will not operate.
Shredder Gapacity:
The cc12 will shred 5 sheets of A4 80gsm paper at once and will accept paper width up to
22Omm.When shredding smaller items like envelopes or credit card leceipts, insert them
through the middle of the feed slot.
The paper sensor is located in the centre of the main feed slot. When paper is inserted, the
sensor starts the cutters. When the paper has gone through the shredder, the sensor will
switch the cutters off.

Operating the Shredder:
1. Prepare the paper to be shredded by removing paper clips and any other objects that
may jam in the feed slot. However, please note the shredder will shred staples, though
for optimal performance, the removal is advised.
2. Only feed 5 sheets of 80 gsm A4 paper at once.
3. Set the select switch on top of the shredder to REV OFF or AUTO position for the
desired operation (See Figure 2).
AUTO: Activates the auto shred function, the shredder will start automatically when an item
is inserted into the paper feed slot and will stop once the paper has been shredded. i
REV: Reverses the shredding direction and backs items out of the shredder in the event of a I
OFF: This position is recommended when emptying the shredder bin or when the shredder
is not in use for a prolonged period of time.
Paper Jams:
The CC12 is equipped with a motor overload protection device; the normal short duty cycle
for continuous shredding a maximum capacity is 2 minutes on & 30 minutes off. The power
may terminate automatically in case of the following situations:
1. Operating the shredder at maximum capacity continuously for a prolonged period of
time, e.g. more than 2 minutes without stopping.
2. Exceeding the shredding capacity e.g. inserting more than 5 sheets at one time, or if the
paper is not fed squarely into the feed slot.
Both of these operations may result in the activation of the automatic motor overload
protection, which terminates the power to the unit. lf this occurs, you should:
1. Unplug the power cord from the AC outlet and wait at least 30 minutes for the overload
protection to reset. Tear or cut off any excess paper from the top of the shredder. ]
2. Plug the power cord back into the AC outlet and place the switch in REV. Pull the
remaining paper out of the cutters. Place the switch back to the AUTO position if
necessary.
3. With the switch in the AUTO position and the feed slot clear, you are now ready to
resume normal shredding.
lf the shredder overheated, it will automatically shut down and will restart again after 30
minutes.
Clearing the Cutter Heads:
lf fibrous paper is being shredded the cutters may become clogged. Move the switch
alternatively between AUTO and REV 2-3 times to clear any paper shreds attached to the
cutters.
ALWAYS UNPLUG THE SHREDDER BEFORE ATTEMPTING TO MANUALLY REMOVE
AN ITEM FROM THE PAPER ENTRY.

Shredding Credit Cards:
1. Set the operating switch to OFF.
2. Plug the shredder into the mains and switch on the power.
3. Set the operating switch to AUTO.
4. Feed credit cards into the centre of the cutting slot one at a time. Allow the machine to
take them in, DO NOT force the card into the machine.
5. Place credit card in vertical position rather than horizontal to achieve better
performance.
6. Do not shred more than one credit card each time.
7. Shredding performance will depend on the thickness, material & hardness of credit
cards.
8. This shredder is designed primarily to shred paper. Occasional shredding of credit cards
will not damage the shredder. Excessive shredding of credit cards could reduce the
life of the blades.
MAINTENANCE
Warninq:
When you want to maintain the shredder, please make sure you have switched off the
shredder and removed the plug from its socket.
9. Use a dry soft cloth when you want to clean the shredder.
10. The shredder cover and waste bin are made of plastic; therefore please do not use
gasoline, benzene impregnate thinner to avoid fading or scratches.
11. Do not allow water to enter the shredder head when cleaning.
I Waste Emptying:
1. when you empty the waste bin, please make sure the unit is switched off and
unplugged.
Place back the shredder head onto the bin correcfly.
Paper is easily wrapped around the shredder head if the waste bin is allowed
to get too full, therefore please empty the waste bin when the bin is full.
HOWTO DISPOSE:
This symbol indicates that you must seek information and follow local
regulations regarding the disposal of this kind of product.
Do not dispose of this product the way you would dispose of general household waste.
Dispose of this product in accordance with the relevant local regulations.
Electrical&Electronic product contains hazardous substances that can harm the
environment and human health, they should be recycled.

TROUBLE SHOOTING
Troubles Reason Solution
Shredder does
not work after
paper inserted.
1. The power cord may not be
properly connected.
2. The paper being shredded
may be too thin to activate the
sensor.
3. The motor has been over
heated.
4. The paper feed may be
jammed.
5. Shredder head is not
placed properly on basket.
1. Check the power cord is correctly
plugged in both the plug socket and the
shredder.
2.Try a thicker paper or fold the paper in
half & try again.
3. Wait for about 30 minutes and try the
shredder again.
4. Reverse the paperfeed and remove
any jammed paper, then try again.
5. Place shredder head securely on
basket, facing the front correctly, ensuring
contact with the basket is made.
Shredder does
not stop after
shredding has
finished
1. The mechanical sensor
may be jammed by paper 1. Clean the paper entry and try again.
Shredder
makes a high
noise
1. The shredder may not be
placed on a flaUstable
surface.
1. Place the shredder onto a flat/stable
surface.
Shredder does
not shred paper
1. Too much paper is inserted.
2. The paper size inserted
may be larger than the paper
entry.
3. The paper may be inclined
when placed into the paper
entrv.
1. Check to see ifyou have exceeded the
rated capacity of paper (5 sheets of
80gsm).
2. Reverse the shredder and take out the
paper, fold in half and try again.
3. Re-insert the paper vertically.

SPECIFICATION
Model: cc12
Voltage: 220-240VAC,50Hz
Current: 0.7A
BS Plug Max 3A Fuse
Paper entry width: 220mm
Shred size: 4*36mm
Shred paper capacitv: 5 sheets 80qsm
Shred speed: 2.0m/min
Waste bin Volume: 12.0L
Noise level: 73DB
Duty cycle: 2 mins on and 30 mins off
Net weisht: 2.9KGs
Dimension: 290.140*360mm
Credit cards YES
Staples YES
Type designation:
Testing acc. to BSEN 60950-1:2006
Low Voltage Directive 2006/95/EC
EMC Directive 20041 1 }BIEC
Test Standards:EN550 1 4-1 :2006
EN550 1 4-2: 1 997 + A1 :2001
EN61000-3-2:2006
EN61000-3-3:2008
Visit www.rvman.co.uk for details on other Ryman products.