Ryobi Roboyagi User manual

ORIGINAL INSTRUCTIONS EN
ÖVERSÄTTNING AV DE URSPRUNGLIGA INSTRUKTIONERNA SV
OVERSÆTTELSE AF DE ORIGINALE INSTRUKTIONER DA
OVERSETTELSE AV DE ORIGINALE INSTRUKSJONENE NO
ALKUPERÄISTEN OHJEIDEN SUOMENNOS FI
ÜBERSETZUNG DER ORIGINALANLEITUNG DE
TRADUCTION DES INSTRUCTIONS ORIGINALES FR
TRADUCCIÓN DE LAS INSTRUCCIONES ORIGINALES ES
TRADUZIONE DELLE ISTRUZIONI ORIGINALI IT
TRADUÇÃO DAS INSTRUÇÕES ORIGINAIS PT
VERTALING VAN DE ORIGINELE INSTRUCTIES NL
ПЕРЕВОД ОРИГИНАЛЬНЫХ ИНСТРУКЦИЙ RU
TŁUMACZENIE INSTRUKCJI ORYGINALNEJ PL
AZ EREDETI ÚTMUTATÓ FORDÍTÁSA HU
PŘEKLAD ORIGINÁLNÍCH POKYNŮ CS
TRADUCEREA INSTRUCŢIUNILOR ORIGINALE RO
PREKLAD ORIGINÁLNYCH POKYNOV SK
PRIJEVOD ORIGINALNIH UPUTA HR
ORIGINAALJUHENDI TÕLGE ET
ORIGINALIŲ INSTRUKCIJŲ VERTIMAS LT
TULKOTS NO ORIĢINĀLĀS INSTRUKCIJAS LV
PREVOD ORIGINALNIH NAVODIL SL
ПРЕВОД ОТ ОРИГИНАЛНИТЕ ИНСТРУКЦИИ BG
ORIJ NAL TALIMATLARIN TERCÜMESI TR
ПЕРЕКЛАД ОРИГІНАЛЬНИХ ІНСТРУКЦІЙ UK

Important! It is essential that you read the instructions in this manual before assembling, operating,
and maintaining the product.
Viktigt! Det är viktigt att du läser instruktionerna i manualen före montering, användning och
underhåll av maskinen.
Vigtigt! Det er meget vigtigt, at man læser anvisningerne i denne brugsanvisning, inden maskinen
samles, betjenes og vedligeholdes.
Viktig! Det er viktig at du leser instruksjonene i denne brukermanualen før du monterer, bruker og
vedlikeholder maskinen.
Tärkeää! On tärkeää, että luet tämän käsikirjan ennen tämän laitteen kokoamista, huoltoa ja käyttöä.
Wichtig! Es ist wichtig, dass Sie vor Zusammenbau, Benutzung und Wartung dieser Maschine die
Anweisungen in dieser Anleitung lesen.
Important! Il est essentiel que vous lisiez les instructions contenues dans ce mode d'emploi avant
d'assembler, d'entretenir et d'utiliser cette machine.
Importante! Antes de montar, de utilizar o de realizar el mantenimiento de esta máquina es muy
importante que lea las instrucciones de este manual.
Importante! È essenziale leggere le istruzioni contenute nel manuale prima di montare, mettere in
funzione e svolgere le operazioni di manutenzione sull'utensile.
Importante! É essencial que leia as instruções neste manual antes de montar, operar e efetuar
manutenção a esta máquina.
Belangrijk! Het is van essentieel belang dat u de instructies in deze gebruiksaanwijzing leest voor u
deze machine monteert, bedient en onderhoudt.
Важное
замечание!
Необходимо прочитать инструкции в данном руководстве перед сборкой,
эксплуатацией и обслуживанием этого устройства.
Ważne! Koniecznie przeczytaj instrukcje zawarte w tym podręczniku przed montażem, obsługą
oraz konserwacją tej maszyny.
Fontos! Fontos, hogy a gép összeszerelése, használata és karbantartása előtt elolvassa a
kézikönyvben található utasításokat.
Důležité! Neinstalujte, neprovádějte údržbu ani nepoužívejte tento nástroj dříve, než si přečtete
pokyny uvedené v tomto návodu.
Important! Este esenţial să citiţi instrucţiunile din acest manual, înainte de asamblarea, operarea sau
întreţinerea acestui aparat.
Dôležité! Pred montážou, používaním a údržbou tohto nástroja je dôležité, by ste si prečítali pokyny
v tomto návode.
Važno! Vrlo je važno da ste prije sklapanja, rada i održavanja ovog stroja pročitali upute u ovom
priručniku.
Oluline! Enne masina kokkupanekut, kasutama ja hooldama hakkamist tuleb käesolevas juhendis
esitatud juhised kindlasti läbi lugeda.
Svarbu! Prieš surinkdami, eksploatuodami ir prižiūrėdami šį įrenginį, būtina, kad perskaitytumėte
nurodymus, pateiktus šiame naudotojo vadove.
Svarīgi! Pirms ierīces montāžas, darbināšanas un apkopes veikšanas obligāti izlasiet norādījumus
šajā rokasgrāmatā.
Pomembno! Zelo pomembno je, da pred sestavljanjem, vzdrževanjem in uporabo te naprave preberete
navodila v tem priročniku.
Важно! Важно е да прочетете инструкциите в това ръководство, преди да сглобявате тази
машина, да работите с нея или да извършвате профилактични дейности.
Önemli! Bu makinenin kurulumunu, bakımını yapmadan, ve makineyi kullanmadan önce bu
kılavuzdaki talimatları okumanız gerekmektedir.
Önemli! Bu makinenin kurulumunu, bakımını yapmadan, ve makineyi kullanmadan önce bu
kılavuzdaki talimatları okumanız gerekmektedir.

x 1
x 1
x 1
x 1
x 1
x 4
x 8
x 150x 4
x 1
x 1
x 1
2

1
2
3
4
5
6
7
8
9
10
12
13
16
17
19
20
21
14
15
11
18
Lietuviškai Latviski Slovensko България Türkçe українська мова
1. Peiliųdiskas 1. Asmeņu disks 1. Disk rezila 1. Режещ диск 1. Bıçak diski 1. Лезо диску
2. Geležtė2. Asmens 2. Rezilo 2. Острие 2. Bıçak 2. Лезо
3. Galinis ratukas 3. Aizmugures ritenis 3. Zadnje kolo 3. Задно колело 3. Arka tekerlek 3. Заднє колесо
4. Akumuliatoriaus
dangtis 4. Akumulatora vāks 4. Pokrov akumu- latorja 4. Капак на батерията 4. Pil kapağı4. Кришка акумуляторного
відсіку
5. Pagrindinis jungiklis 5. Galvenais slēdzis 5. Glavno stikalo 5. Главен
превключвател 5. Ana şalter 5. Головний вимикач
6. Ekranas 6. Displejs 6. Zaslon 6. Дисплей 6. Ekran 6. Дисплей
7. Grįžties mygtukas 7. Poga "Atpakaļ" 7. Gumb nazaj 7. Бутон за връщане
назад 7. Geri düğmesi 7. Кнопка вмикання
8. Pasirinkimo
rankenėlė8. Atlasīšanas poga 8. Izbirno stikalo 8. Селекторно копче 8. Seçme düğmesi 8. Перемикач
9. Patvirtinimo mygtu-
kas/įjungimo-iš-
jungimo mygtukas
9. Apstiprināšanas
poga/
Ieslēgšanas-izs-
lēgšanas poga
9. Gumb za potrditev/
gumb za vklop-iz-
klop
9. Бутон за
потвърждение/
бутон за
включване и
изключване
9. Doğrulama düğme-
si/Açma-kapama
düğmesi
9. Кнопка
підтвердження/
вимикання
10. Sustabdymo
mygtukas 10. Apturēšanas poga 10. Gumb stop 10. Бутон за спиране 10. Stop düğmesi 10. Кнопка зупинки
11. Valdymo skydelis 11. Vadības panelis 11. Nadzorna plošča 11. Пулт за
управление 11. Kumanda panosu 11. Панель управління
12. Šviesos diodų
indikatorius 12. Indikators 12. Indikator LED 12. Светодиоден индикатор 12. LED gösterge 12. Світлодіодний індикатор
13. Įkrovimo prievadas 13. Lādēšanas
pieslēgvieta 13. Vhod za polnjenje 13. Порт за зареждане 13. Şarj girişi 13. Порт для
заряджання
14. Įkrovimo pagrindas 14. Lādēšanas paliktnis 14. Polnilna plošča 14. Подложка за
зареждане 14. Şarj yastığı14. Зарядний майданчик
15. Transformatorius 15. Transformators 15. Transformator 15. Трансформатор 15. Transformatör 15. Трансформатор
16. Įkrovimo blokas 16. Lādēšanas stacija 16. Polnilna postaja 16. Зарядна станция 16. Şarj istasyonu 16. Зарядна станція
17. Valdymo skydelio
dangtelis 17. Vadības paneļa vāks 17. Pokrov nadzorne plošče17. Капак на пулта за управление 17. Kumanda panosu kapağı
17. Кришка панелі
управління
18. Vejapjovės blokas 18. Trimmera mezgls 18. Sestav rezil 18. Комплект на
тримера 18. Budayıcıtertibatı18. Тример узборі
19. Priekinis ratukas 19. Priekšējais ritenis 19. Sprednje kolo 19. Предно колело 19. Ön tekerlek 19. Переднє колесо
20. Įkrovimo lizdas 20. Lādēšanas kontak-
tdakša 20. Vtičnica za polnjenje 20. Гнездо за зареждане 20. Şarj soketi 20. Зарядний роз'єм
21. Įspėjimo signalas 21. Trauksme 21. Alarm 21. Аларма 21. Alarm 21. Звуковий сигнал
попередження
Español Italiano Português Nederlands Pусский Polski Magyar Čeština RomânăSlovenčina Hrvatski Eesti
1. Disco de la cuchilla 1. Disco portalama 1. Disco da lâmina 1. Maaischijf 1. Режущий диск 1. Tarcza noży 1. Késtárcsa 1. Nožový kotouč1. Discul lamelor 1. Disk noža 1. Disk noža 1. Lõikeketas
2. Hoja 2. Lama 2. Lâmina 2. Zaagblad 2. Пильное полотно 2. Ostrze 2. Kés 2. Nůž 2. Lamă2. Ostrie 2. Oštrica 2. Saeleht
3. Rueda trasera 3. Ruote posteriori 3. Roda traseira 3. Achterwiel 3. Заднее колесо 3. Koło tylne 3. Hátsó kerék 3. Zadní kolo 3. Roatăspate 3. Zadné koleso 3. Stražnji kotač3. Tagaratas
4. Cubierta de la
batería 4. Coperchio della batteria 4. Tampa da bateria 4. Accuklep 4. Крышка аккумуляторного
отсека
4. Pokrywa baterii 4. Akkumulátor fedél 4. Kryt baterie 4. Capacul acumula-
torului 4. Kryt batérie 4. Poklopac baterije 4. Aku kaas
5. Interruptor principal 5. Interruttore generale 5. Interruptor principal 5. Hoofdschakelaar 5. Главный
выключатель 5. Wyłącznik główny 5. Főkapcsoló 5. Hlavní vypínač5. Comutator principal 5. Hlavný vypínač5. Glavni prekidač5. Pealüliti
6. Pantalla 6. Display 6. Visor 6. Beelscherm 6. Дисплей 6. Wyświetlacz 6. Kijelző6. Displej 6. Afișaj 6. Displej 6. Zaslon 6. Ekraan
7. Botón Atrás 7. Tasto Indietro 7. Botão para retro-
ceder 7. Achterste knop 7. Кнопка назад 7. Przycisk tylny 7. Vissza gomb 7. Tlačítko zpět 7. Buton spate 7. Tlačidlo späť7. Gumb za vraćanje unatrag 7. Tagasi-nupp
8. Mando selector 8. Manopola del
selettore 8. Seletor 8. Selectieknop 8. Регулятор 8. Pokrętło wybier- ające 8. Választógomb 8. Otočný volič8. Selector 8. Prepínací
gombík 8. Gumb birača 8. Valiku-nupp
9. Botón Confirmar/
botón de encendi-
do-apagado
9. Pulsante Conferma/
Tasto On-off 9. Botão Confirmar/ botão Ligar/Desligar 9. Bevestigingknop/ aan/uit-knop 9. Кнопка подтверждения/
кнопка вкл-выкл
9. Przycisk potwi-
erdzenia/przycisk
włącznika
9. Megerősítőgomb/
be-ki gomb 9. Potvrzovací tlačítko/ chod 9. Buton confirmare/ Buton On-off 9. Potvrdzovacie tlačidlo/tlačidlo on-
off (zapnúť-vypnúť)
9. Potvrdni gumb/
gumb za uključivan-
je i isključivanje
9. Kinnita-nupp/Sisse-
välja-nupp
10. Botón Parada 10. Pulsante Arresta 10. Botão Parar 10. Stopknop 10. Кнопка стоп 10. Przycisk zatrzy-
mania 10. Leállító gomb 10. Tlačítko zastavení 10. Buton stop 10. Tlačidlo zastavenia 10. Gumb zaustavljanja 10. Stopp-nupp
11. Panel de control 11. Pannello di controllo 11. Painel de controlo 11. Bedieningspaneel 11. Панель
управления 11. Panel sterowania 11. Kezelőpanel 11. Ovládací panel 11. Panou de comandă11. Ovládací panel 11. Upravljačka ploča 11. Juhtpaneel
12. Indicador luminoso 12. Spia luminosa 12. Luz 12. LED-aanduiding 12. Световой
индикатор 12. Lampka kontrolna 12. Világító kijelző12. Světelná kontrolka 12. Indicator luminos 12. LED kontrolka 12. Signalna lampica 12. LED märgutuli
13. Puerto de carga 13. Porta di carica-
mento 13. Porta de carrega-
mento 13. Oplaadpoort 13. Зарядный порт 13. Port ładowania 13. Töltőport 13. Nabíjecí konektor 13. Port de încărcare 13. Nabíjací port 13. Priključak za
punjenje 13. Laadimisport
14. Base de carga 14. Base di carica 14. Suporte de carre-
gamento 14. Oplaadkussen 14. Зарядная панель 14. Podkładka ładująca 14. Dokkoló 14. Parkovací podložka 14. Plăcuțde încărcare 14. Nabíjacia podložka 14. Podloga za punjenje 14. Laadimisalus
15. Transformador 15. Trasformatore 15. Transformador 15. Transformator 15. Трансформатор 15. Transformator 15. Transzformátor 15. Napájecí adaptér 15. Transformator 15. Transformátor 15. Transformator 15. Trafo
16. Estación de carga 16. Stazione di ricarica 16. Base de carrega-
mento 16. Oplaadstation 16. Зарядная станция 16. Stacja ładująca 16. Töltőállomás 16. Nabíjecí stanice 16. Stație de încărcare 16. Nabíjacia stanica 16. Postaja za punjenje 16. Laadimisjaam
17. Cubierta del panel
de control 17. Coperchio pannello di controllo 17. Tampa do painel de controlo 17. Afdekking bedien- ingspaneel 17. Крышка панели управления 17. Pokrywa panelu sterowania 17. Kezelőpanel burkolata 17. Kryt ovládacího panelu 17. Capac panou de comandă17. Kryt ovládacieho panela 17. Poklopac upravl- jačke ploče17. Juhtpaneeli kate
18. Conjunto de la
recortadora 18. Gruppo tagliaerba 18. Conjunto do aparador 18. Trimmermodule 18. Блок триммера 18. Zespółpodkaszarki 18. Vágószerelvény 18. Sestava nůžek 18. Ansamblu tăietor 18. Orezávač18. Sklop trimera 18. Trimmeri lisaseade
19. Rueda delantera 19. Ruote anteriori 19. Roda frontal 19. Voorwiel 19. Переднее колесо 19. Koło przednie 19. Elülsőkerék 19. Přední kolo 19. Roatăfaţă 19. Predné koleso 19. Prednji kotač19. Esiratas
20. Conector de carga 20. Presa di carica 20. Tomada de carre-
gamento 20. Oplaadcontact 20. Разъем для зарядки 20. Gniazdo ładowania 20. Töltőaljzat 20. Nabíjecí zásuvka 20. Priza de încărcare 20. Zásuvka na nabíjanie 20. Utičnica za punjenje 20. Laadimise pistik- upesa
21. Alarma 21. Allarme 21. Alarme 21. Alarm 21. Сигнализация 21. Alarm 21. Riasztó 21. Signalizace 21. Alarmă21. Alarm 21. Alarm 21. Alarm
English Svenska Dansk Norsk Suomi Deutsch Français
1. Blade disc 1. Knivskiva 1. Klingeskive 1. Bladskive 1. Teräkiekko 1. Messerteller 1. Lame circulaire
2. Blade 2. Knivblad 2. Klinge 2. Blad 2. Terä 2. Messer 2. Lame
3. Rear
wheel 3. Bakhjul 3. Baghjul 3. Bakhjul 3. Takapyörä 3. Hinterrad 3. Roue arrière
4. Battery cover 4. Batterihölje 4. Batteridæksel 4. Batterideksel 4. Akun kansi 4. Akku-Abdeck-
haube 4. Couvercle de la batterie
5. Master switch 5. Huvudström-
brytare 5. Hovedkontakt 5. Masterbryter 5. Pääkytkin 5. Hauptschalter 5. Contacteur principal
6. Display 6. Display 6. Display 6. Display 6. Näyttö 6. Display 6. Affichage
7. Back button 7. Bakre knapp 7. Tilbage-knap 7. Tilbakeknapp 7. Takaisin-painike 7. Zurücktaste 7. Bouton Retour
8. Selector knob 8. Väljarvred 8. Valggreb 8. Velgerbryter 8. Valintanuppi 8. Auswahl-Con-
troller 8. Molette de sélection
9. Confirm button/
On-off button 9. Bekräf- telseknapp/
på-av-knapp
9. Bekræft-knap/
Tænd-/Sluk-
knap
9. Bekreftknapp/
på-av-knapp 9. Vahvistuspain- ike/Päälle-Pois
päältä -painike
9. Bestätigung-
staste/Ein-/
Ausschalter
9. Bouton de con-
firmation/Bouton
Marche-Arrêt
10. Stop button 10. Stoppknapp 10. Stopknap 10. Stoppknapp 10. Pysäytyspainike 10. Stopptaste 10. Bouton d'arrêt
11. Control Panel 11. Kontrollpanel 11. Kontrolpanel 11. Kontrollpanel 11. Ohjauspaneeli 11. Bedienfeld 11. Panneau de
commande
12. LED indicator 12. Kontrollampa 12. Kontrollampe 12. Lys 12. Merkkivalo 12. Leuchtdiode 12. Voyant lumineux
13. Charging port 13. Laddningsport 13. Opladeport 13. Ladeport 13. Latausportti 13. Ladeanschluss 13. Port de charge
14. Charging pad 14. Laddningsplatta 14. Ladepuder 14. Ladepute 14. Latausalusta 14. Lade-Pad 14. Socle de charge
15. Transformer 15. Transformator 15. Transformer 15. Transformator 15. Muuntaja 15. Transformator 15. Transformateur
16. Charging station 16. Laddningssta-
tion 16. Ladestation 16. Ladestasjon 16. Latausasema 16. Ladestation 16. Poste de charge
17. Control panel
cover 17. Kontrollpan- elskydd 17. Kontrolpan- eldæksel 17. Kontrollpan- eldeksel 17. Ohjauspaneelin luukku 17. Bedienfeldab- deckung 17. Couvercle du panneau de
commande
18. Trimmer
assembly 18. Trimmermonter- ing 18. Trimmersamling 18. Trimmerenhet 18. Trimmeripään kokoonpano 18. Montage des Trimmers 18. Ensemble de coupe
19. Front wheel 19. Framhjul 19. Forhjul 19. Forhjul 19. Etupyörä 19. Vorderrad 19. Roue avant
20. Charging socket 20. Laddningsuttag 20. Ladestik 20. Ladeuttak 20. Latausliitäntä 20. Ladebuchse 20. Prise de charge
21. Alarm 21. Larm 21. Alarm 21. Alarm 21. Hälytys 21. Alarm 21. Alarme
3

4

EN
SV
DA
NO
FI
DE
FR
ES
IT
PT
NL
RU
PL
HU
CS
RO
SK
HR
ET
LT
LV
SL
BG
TR
UK
ENGLISH
5
CONTENTS
Intended use 7
Safety warnings 7
Battery safety warnings 7
Additional battery safety warnings 8
Transporting lithium batteries 8
Charging station safety warnings 8
Lawn mower safety warnings 8
Product features 9
Bump sensors 9
Lift sensors 9
Area sensors 9
Tilt sensor 9
Charging detection sensor 9
Alarm 9
Symbols on the product 9
Symbols in this manual 9
Residual risks 9
Maintenance 10
Clearing blockages 10
Performing installation checks 10
Main components 10
Accessories 11
Installing the boundary wire 11
Methods of boundary wire installation 11
Conditions of laying the boundary wire 11
Work area boundaries 11
Splicing the boundary wires 11
Installing and connecting the Charging station 11
Installing the Charging station 11
Connecting the power supply 12
Charging the mower 12
Using the control panel 12
Setting up for first-time use 13
LCD screen overview 14
Dashboard 14
Entering security pin 14
Menu 14
Stopping/resuming the product 14
Docking the product 14
Selecting a cutting mode 14
Mow to Schedule 14
Manual 15
Perimeter trim 15
Setting a schedule 15
Configuring the product 15

ENGLISH
6
Mowing Parameters 15
Advanced settings 16
Mowing zones 17
Mowing Zone A 17
Mowing Zone B 17
Mowing Zone C 17
Mowing Zone D 17
Mowing Zone E 17
Mowing Zone F 17
Mowing Zone G 17
Mowing Zone H 18
Troubleshooting 19
Problem 19
Possible cause 19
Solution 19
Serial Number / UID:
PIN CODE
Username:
Password:

EN
SV
DA
NO
FI
DE
FR
ES
IT
PT
NL
RU
PL
HU
CS
RO
SK
HR
ET
LT
LV
SL
BG
TR
UK
ENGLISH
7
Safety, performance, and dependability have been
given top priority in the design of your robotic lawn
mower.
INTENDED USE
The robotic lawn mower is only intended for use
outdoors.
The product is designed for domestic lawn mowing.
The cutting blade should rotate approximately parallel
to the ground of an open and level work area.
The product should never be operated with the wheels
off the ground; it should not be pulled or ridden on. It
should not be used to cut anything other than domestic
grass lawns.
Do not use the product for any other purpose.
SAFETY WARNINGS
WARNING
When using the product, the safety rules must be
followed. For your own safety and that of bystanders,
please read these instructions before operating the
product. Please keep the instructions safe for later
use.
WARNING
The product should only be operated with the battery
packs specified in this manual. When using battery-
operated products, basic safety precautions should
always be followed to reduce the risk of fire, leaking
batteries and personal injury.
■The product is capable of amputating hands and
feet, and of throwing objects. Failure to observe all
safety instructions could result in serious injury or
death.
■Be familiar with the controls and the correct use of
the product.
■Never allow children or people with reduced
physical, sensory or mental capabilities or persons
not familiar with these instructions to operate, clean
or maintain the product. Local regulations may
restrict the age of the operator. Children should be
adequately supervised to ensure they do not play
with the product.
■Keep all bystanders, especially children and pets, at
least 15 m away from the area of operation.
■Objects struck by the lawn mower blade can cause
severe injuries to persons. Thoroughly inspect the
area where the product is to be used and remove
all rocks, sticks, metals, wires, bones, toys, or other
foreign objects. Remember, string or wire may
entangle with the blades.
WARNING
Blades coming in contact with a “live” wire may make
exposed metal parts of the product “live” and could
cause an electric shock.
■Do not use the product when there is a risk of
lightning.
■Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people
or their property.
■Keep children out of the mowing area and under the
watchful care of a responsible adult other than the
operator. Be alert and turn off the product if a child
enters the area.
■Read, understand, and always follow the safety
instructions that came with the product. Failure
to do so may result in electric shock, fi
re or other
hazardous situations. Keep all the instructions
together in a safe place for future reference.
■Do not use the product under dusty or foggy
environment, or when there is a rain storm.
■Use the product in the daylight or with good artificial
light.
BATTERY SAFETY WARNINGS
■Use only battery pack intended specifically for the
product. Use of any other battery packs may result
in a risk of fire, electric shock, or injury to persons.
■When the battery pack is not in use, keep it away
from other metallic objects such as paper clips,
coins, keys, nails, screws, or other small metallic
objects, that can make a connection from one
terminal to another. Shorting the battery pack
terminals together may cause sparks, burns, fire or
explosion.
■Do not place battery products or their batteries near
fire or heat; this increases the risk of explosion and
possibly injury.
■Do not incinerate the battery.
■Do not open or puncture the battery pack. Released
electrolyte is corrosive, may cause damage to the
eyes or skin, and may be toxic if swallowed.
■Protect the battery pack against moisture and
water. Do not charge the product in a damp or wet
locationt to reduce the risk of electric shock.
■In case of damage and improper use of the battery,
vapour may be emitted. Provide for fresh air and
seek medical help in case of complaints. The
vapour can irritate the respiratory system.
■Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid comes
in contact with the eyes, additionally seek medical
help. Battery leaks may cause irritation or burns.

ENGLISH
8
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fluid or allow a fluid
to flow inside them. Corrosive or conductive fluids,
such as seawater, certain industrial chemicals, and
bleach or bleach-containing products, etc., can
cause a short circuit.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and
national provisions and regulations.
Follow all special requirements on packaging and
labelling when transporting batteries by a third party.
Ensure that no batteries can come in contact with other
batteries or conductive materials while in transport by
protecting exposed connectors with insulating, non-
conductive caps or tape. Do not transport batteries
that are cracked or leaking. Check with the forwarding
company for further advice.
CHARGING STATION SAFETY WARNINGS
■Power plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of
electric shock.
■Electrical power should be supplied via a residual
current device (RCD) with a tripping current of not
more than 30 mA.
■Before use, check the supply and extension cord
for signs of damage or aging. If the cord becomes
damaged during use, disconnect the cord from the
supply immediately. Do not touch the cord before
disconnecting the supply. Do not use the product if
the cord is damaged or worn.
■If you need to use an extension cord, ensure it is
suitable for outdoor use and has a current capacity
rating sufficient to supply your product. Check
the extension cord before every use for damage.
Always uncoil it during use because coiled cords
can overheat. Damaged extension cord should
not be repaired. They should be replaced with an
equivalent type.
■Make sure the power cord is positioned so that it
cannot be damaged by the blades and will not be
stepped on, tripped over, or subjected to damage
or stress.
■Never pull by the power cord to disconnect from the
power supply.
■Keep the power cord away from heat, oil and sharp
edges.
■Make sure the voltage is correct for your product. A
rating label on the product indicates the product’s
voltage. Never connect the product to an AC
voltage that differs from the voltage indicated on the
rating label.
LAWN MOWER SAFETY WARNINGS
■Perform weekly visual inspections to ensure blades,
blade bolts, and cutter assembly are not worn or
damaged.
■Replace worn or damaged blades and bolts in sets
to preserve balance.
■The blade on the product is sharp. Use extreme
caution and wear heavy-duty gloves when fitting,
replacing, cleaning, or checking bolt security.
■Bring the product to an authorised service centre to
replace damaged or unreadable labels.
■Replace worn or damaged parts before operating
the product.
■Never start the product if the hands and feet of all
persons are not clear of the cutting enclosure.
■Do not use the product if the master switch does not
turn it on or off.
■Never attempt to lock the master switch in the on
position; this is extremely dangerous.
■Never use the product with defective guards or
shields, or without safety devices in place.
■Turn on the product carefully according to
instructions, and keep hands and feet away from
blades. Do not put hands or feet near or under
rotating parts.
■Never pick up or carry the product while it is running.
■Stop the product and make sure that all moving
parts have come to a complete stop:
●before clearing blockages or unclogging
●before checking, cleaning, or working on the
product
●after striking a foreign object (inspect the
product for damage and make repairs as
necessary before restarting and operating the
product)
■If the product starts to vibrate abnormally (check
immediately)
●inspect for damage, particularly the blades
●replace or repair any damaged parts
●check for and tighten any loose parts
■Do not use the product simultaneously with the
sprinkler systems.
■Do not use the product when it is snowing.

EN
SV
DA
NO
FI
DE
FR
ES
IT
PT
NL
RU
PL
HU
CS
RO
SK
HR
ET
LT
LV
SL
BG
TR
UK
ENGLISH
9
WARNING
Never touch exposed terminals at all times.
PRODUCT FEATURES
The mower is equipped with several sensors that
protect both the mower and the user. Bump sensors,
lift sensors, area sensors, a tilt sensor, and a charging
station sensor are built-in safety features of the mower.
The mower also has a built-in alarm that alerts the user
when the mower is in a fault state and requires the
security PIN to be entered.
BUMP SENSORS
The bump sensors detect when the mower bumps
into an obstacle. When the sensors are activated, the
mower stops and then turns to continue in a different
direction.
LIFT SENSORS
The lift sensors detect when the mower is lifted from
the ground during the operation. When the sensors are
activated, the wheels and blades on the mower stop
immediately.
AREA SENSORS
The area sensors keep the mower within the defined
boundary by sensing the proximity of the mower to the
wire.
TILT SENSOR
The tilt sensor detects when the mower is tilted in
relation to the horizontal plane. The sensor is activated
and immediately stops the wheels and blades when the
mower is tilted to 25°.
CHARGING DETECTION SENSOR
The charging detection sensor is activated when the
mower is docked at the charging station.
ALARM
The built-in alarm is triggered when the mower is in a
fault state and requires the security PIN to be entered.
The alarm is also set off when the security PIN is not
entered within the required time after the stop button is
pressed or if the mower is lifted off the ground.
SYMBOLS ON THE PRODUCT
Read and understand all instructions
before operating the product, follow all
warnings and safety instructions.
Operate the disabling device before
working on or lifting the product.
Beware of sharp blades. Blades
continue to rotate after the motor is
turned off.
Beware of thrown or flying objects.
Keep all bystanders, especially
children and pets, at least 15 m away
from the area of operation.
Stop the product before performing
any maintenance tasks. The product
should not be ridden on.
SMPS (Switch mode power supply
unit)
SMPS incorporating a short-circuit-
proof safety isolating transformer
Class II tool
Time-lag fuse 3.15 A
Class III electrical protection
Conforms to all regulatory standards
in the country in the EU where the
product is purchased.
EurAsian Conformity Mark
Ukrainian mark of conformity
Recycle raw materials instead of
disposing of as waste. The machine,
accessories, and packaging should
be sorted for environmental-friendly
recycling.
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authority or
retailer for recycling advice.
SYMBOLS IN THIS MANUAL
Parts or accessories sold separately

ENGLISH
10
Note
Warning
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise during use
and the operator should pay special attention to avoid
the following:
■injury from contact with the blades
■injury caused by thrown objects
MAINTENANCE
WARNING
Use only original manufacturer’s replacement parts,
accessories and attachments. Failure to do so
can cause possible injury, can contribute to poor
performance, and may void your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. For servicing and repairs, have the
product serviced by an authorised service centre
only. When servicing, use only original replacement
parts.
■Stop the product and make sure that all moving
parts have come to a complete stop before any
cleaning or maintenance task.
■You may make adjustments and repairs described
in this manual. For other repairs, have the product
serviced by an authorised service centre only.
■Replace worn or damaged parts for safety.
■Clean the product once a week with a soft, dry
cloth. Any part that is damaged should be properly
repaired or replaced by an authorised service
centre.
■Perform weekly checks on the blade disc screws,
blade nuts, and blade screws to ensure proper
tightness. Check all other nuts, bolts, and screws
monthly for proper tightness to ensure the product
is in safe working condition.
■Be careful during adjustment of the product to
prevent entrapment of the fingers between moving
blades and fixed parts of the product.
■When servicing the blades, be aware that even
though the power source is turned off, the blades
can still be moved.
■The blade on the product is sharp. Use extreme
caution and wear heavy-duty gloves when fitting,
replacing, cleaning, or checking bolt security.
■Replace damaged blades and bolts in sets to
preserve balance.
■The blade bolts must be adequately tightened. See
the manufacturer’s recommendations for blade
bolt torque, which can be found in the product
specification table in this manual.
■Keep the blades sharp and clean to prevent loss
of control.
CLEARING BLOCKAGES
■Stop the product and make sure that all moving
parts have come to a complete stop.
■Always wear heavy-duty gloves when checking or
clearing a blockage.
■The blades are sharp and the blockage itself could
be a sharp object.
WARNING
Use extreme caution when lifting or tilting the product
for maintenance, cleaning, storage, or transportation.
The blade is sharp. Keep all body parts away from
the blade while exposed.
PERFORMING INSTALLATION CHECKS
See pages 14 - 15
MAIN COMPONENTS
1. MOWER
The product mows the lawn automatically within a
perimeter set by the boundary wire.
2. BATTERY PACK
The product is powered by a 36 V battery pack.
3. CHARGING STATION
The product recharges its battery pack at the
charging station. The product returns to the
charging station when the mowing is done or the
battery pack needs to be recharged.
The two parts of the charging station are the
charging port and charging pad. The charging port
connects to the charging socket of the product
when the product is docked. The charging station
emits the signal that allows the mower to locate the
charging station.
The charging station must be placed on a levelled
ground, protected from sprinkler systems, rain,
snow, and direct sunlight.

EN
SV
DA
NO
FI
DE
FR
ES
IT
PT
NL
RU
PL
HU
CS
RO
SK
HR
ET
LT
LV
SL
BG
TR
UK
ENGLISH
11
4. TRANSFORMER
The transformer is a 42 V, 3 A DC power adapter.
It is connected between the charging station and a
220 V – 240 V power supply.
The transformer must be placed near the charging
station, protected from sprinkler systems, rain,
snow, and direct sunlight.
5. POWER CORD
The power cord connects the transformer to the
charging station.
6. BOUNDARY WIRE
The boundary wire is laid in a loop around the work
area of the mower. The boundary wire is also set
around the edges of the lawn, ornaments, plants,
and other obstacles that the mower must avoid
during operation.
ACCESSORIES
7. CHARGING STATION SCREWS
The charging station screws hold the charging
station in place.
8. PEGS
The pegs are used to hold the boundary wire in
place.
9. WIRE CONNECTORS
The wire connectors are used to connect the
boundary wire and the charging station.
10. COUPLERS
The couplers are used to connect two lengths of the
boundary wires.
11. T25 SCREW DRIVER
A T25 screw driver is shipped with the product for
installation and removal purposes.
INSTALLING THE BOUNDARY WIRE
METHODS OF BOUNDARY WIRE INSTALLATION
USING THE PEGS
Use a hammer / rubber mallet to secure the pegs
to the ground and hold the boundary wire in place.
CONDITIONS OF LAYING THE BOUNDARY WIRE
The boundary wire must form a loop around the work
area of the product. The product will operate only within
the bounded perimeter. Only the original boundary
wire, designed and supplied by the manufacturer, must
be used. Using a different boundary wire may cause
performance issues and damage to the product.
■Do not coil the boundary wire.
WORK AREA BOUNDARIES
OBSTACLES
The boundary wire should be laid 45 cm from the
obstacle that borders the work area and is 1.5 cm
or more in height. This will prevent the mower from
colliding with the obstacle and reduce body wear.
About 30 cm of the lawn around the fixed obstacle
will not be mowed.
SOFTSCAPES
The boundary wire should be laid 45 cm from the
obstacle that borders the work area and is 1.5 cm
or more in height. This will prevent the mower from
colliding with the obstacle and reduce body wear.
About 30 cm of the lawn around the fixed obstacle
will not be mowed. Flower beds, trees, plants,
grass, and mulches are examples of softscapes.
HARDSCAPES
The boundary wire should be laid 45 cm from the
obstacle that borders the work area and is 1.5 cm
or more in height. This will prevent the mower from
colliding with the obstacle and reduce body wear.
About 30 cm of the lawn around the fixed obstacle
will not be mowed. Sidewalks, pavers, rocks,
decks, and patios are examples of hardscapes. The
boundary wire should be laid at least 5 cm away
from the flat paving stone or flat pavement.
NOTE: The mower must never run over gravel, mulch,
or similar material that can damage the blades.
NOTE: An edging that is at least 60 cm must be used
if the work area is adjacent to a pool, steep slopes, or
a public road. This will prevent the mower from ending
up outside the working area under any circumstance.
NOTE: Set up the boundary away from high-voltage
posts or devices. Do not set up the boundary near heat
or fire sources, or explosive environment.
SPLICING THE BOUNDARY WIRES
Use an original coupler if the boundary wire is not long
enough for the work area and needs to be spliced.
Insert both wire ends into the coupler. Check that the
boundary wires are fully inserted into the coupler. Both
ends of the boundary wires should be visible through
the transparent area on the other side of the coupler.
Press the button on top of the coupler to connect the
both ends of the boundary wires. If necessary, use a
polygrip to completely press down the button on the
coupler.
INSTALLING AND CONNECTING THE CHARGING
STATION
INSTALLING THE CHARGING STATION
■Place the charging station on a levelled ground and
ensure that no objects or obstructions are in the

ENGLISH
12
immediate vicinity.
■The charging station must be positioned with
enough free space.
■Protect the charging station from water sprinkler
systems.
■Protect the charging station from direct sunlight.
■Do not put the charging station in confined spaces
in the work area. This can make it difficult for the
product to find the charging station.
■The charging station must not be positioned in a
way that its charging pad is bent.
■The charging station must not be placed on an
defined obstacle as this limits the optimal operation
of the boundary wire.
■Position the charging station in a suitable spot.
■Mount the charging station to the ground using
the supplied charging station screws. Ensure the
screws are securely tightened all the way down in
the countersink. If the charging station is placed
against a wall, it is best to wait before securing
the charging station to the ground until after all the
wires have been connected.
CONNECTING THE POWER SUPPLY
■The transformer must be protected from rain and
direct sunlight.
■If the transformer is connected to an outdoor power
outlet, ensure the power outlet is designed for
outdoor use.
WARNING
The transformer cable must not, under any
circumstances, be shortened or extended.
■Make sure the transformer cable is laid along the
ground and secured with pegs. The cable must lay
close to the ground so as not to be cut before the
grass roots have grown over it.
WARNING
Place the transformer cable so that the blades can
never come in contact with the cable.
■The transformer must be placed in a well-ventilated
area. Do not expose to direct sunlight.
■Do not, under any circumstances, mount the
transformer at a height where there is a risk of it
being submerged in water. The transformer must
not be placed on the ground.
■Never connect the transformer to the power outlet if
the plug or cord is damaged. Damaged or entangled
cord increases the risk of electric shock.
■Connect the transformer’s power cable to a 100 -
240 V mains.
CHARGING THE MOWER
As soon as the charging station is connected, it is
possible to charge the mower.
■Turn on the master switch, which is located at the
underside of the mower.
■Dock the mower to the charging station.
WARNING
Do not use the product until the installation is
complete.
USING THE CONTROL PANEL
1
2
3
4
5
The product settings are managed through the control
panel.
1. Back button
This button is used to return the user to a previous
menu screen.

EN
SV
DA
NO
FI
DE
FR
ES
IT
PT
NL
RU
PL
HU
CS
RO
SK
HR
ET
LT
LV
SL
BG
TR
UK
ENGLISH
13
2. Selector knob
This knob navigates through various items for
selection.
3. Confirm button/On-Off button
This button is used to confirm the selection of a
highlighted item. This button also functions as an
on/off button while the master switch is turned on.
Press this button to turn on the product. Press and
hold this button to turn off the product.
NOTE: This button is disabled when the master
switch is turned off.
4. Stop button
This button stops the product and opens the control
panel cover.
NOTE: Close the control panel cover to resume
operation.
5. Display
The display screen shows the status of the product
and the menu options.
SETTING UP FOR FIRST-TIME USE
NOTE: Make sure the master switch is turned on and
the mower is properly docked.
1. Press and hold the confirm button until the RYOBI
logo appears.
2. Using the selector knob, choose a preferred
language. Press the confirm button.
3. Read through the information and press the confirm
button.
4. Choose the first digit of your security PIN. Press
the confirm button. Repeat the step to choose the
succeeding digits of your security PIN.
5. Re-enter your security PIN.
If the security PIN setup is successful, a confirmation
screen appears. If PIN code mismatch appears,
repeat step 4.
6. Press the confirm button.
7. To set up Wi-Fi, select one of the following:
●[YES]: Set up the Wi-Fi connection. For
instructions, refer to the “Wi-Fi Setup” section.
●[NO]: Set up the Wi-Fi connection at a later time.
If there is no Wi-Fi signal or if [NO] is chosen,
manually set the date and time.
8. On the [Date/Time Setup] screen, choose the date.
a. With [dd] highlighted, choose the day. Press the
confirm button.
b. With [mm] highlighted, choose the month. Press
the confirm button.
c. With [yy] highlighted, choose the year. Press the
confirm button.
9. Choose the time.

ENGLISH
14
a. With [--:] highlighted, choose the hour. Press the
confirm button.
b. With [:--] highlighted, choose the minute. Press
the confirm button.
10. Press the confirm button.
11. On the [Setup] screen, press the confirm button.
12. Choose a prefered cut height. Press the confirm
button.
13. Press the confirm button.
14. To set up the docking direction, select one of the
following:
●[CW]: The mower will go back to the charging
station in a clockwise direction.
●[CCW]: The mower will go back to the charging
station in a counterclockwise direction.
15. Press the confirm button.
16. To set up the mowing schedule, select one of the
following:
●[YES]: Set up the mowing schedule. For
instructions, refer to the “Setting a schedule”
section.
●[NO]: Set up the mowing schedule at a later
time.
If [NO] is chosen on the [Schedule Setup] screen,
perform a perimeter test run.
17.
On the [Perimeter Test Run] screen, read through
the information and select one of the following:
●[Start test]: Start the perimeter test run.
●[Do it later]: Perform the perimeter test run at
a later time.
18.
Read the warning text, then press the confirm
button to continue.
19. Read and follow the instructions on the display
screen. Press the confirm button to continue.
20. A [Perimeter Test Run] screen appears. Close the
control panel cover to start testing.
NOTE: To stop the perimeter testing, press the stop
button. Follow the instructions on the control panel
screen of the product to either continue test run or
cancel test run.
LCD SCREEN OVERVIEW
DASHBOARD
1
2
34
5
6
The dashboard provides information of the product
status and current settings.
1. Displays the current status of the product.
2. Specifies the cutting operation of the product.
3. Displays the cut height.
4. Indicates the Wi-Fi connection strength.
5. Displays the current battery charge.
6. Displays the date and time.
ENTERING SECURITY PIN
1. Enter your security PIN.
2. With
[Confirm] highlighted, press the confirm button.
MENU
Start
1
2
34
6
5
Access the menu to perform the following tasks:
1. Direct the product to return to the charging station.
2. Check active alerts and historical alerts.
3. Configure the mower parameters, advanced
settings, and perimeter test run.
4. View, add, edit, or delete schedules for cutting.
5. Select the mow to schedule, manual, or perimeter
trim modes.
6. Start or resume the product cutting operation.
STOPPING/RESUMING THE PRODUCT
●To stop the product, press the stop button. The
control panel cover opens
●To resume the product, choose [ ] from the
menu, then close the control panel cover.

EN
SV
DA
NO
FI
DE
FR
ES
IT
PT
NL
RU
PL
HU
CS
RO
SK
HR
ET
LT
LV
SL
BG
TR
UK
ENGLISH
15
DOCKING THE PRODUCT
1. From the menu, choose [ ]. The [Go Home] screen
appears.
2. From the [Go Home] screen, do one of the following:
●[Stay in the dock]: Let the product remain
connected to the charging station. Press
confirm button to continue.
●[Follow schedule]: Continue with the set mowing
schedule. Press confirm button, then close the
control panel cover to continue.
SELECTING A CUTTING MODE
From the [Cutting Mode] screen, choose from the
following cutting modes.
■[Mow to Schedule]
■[Manual]
■[Perimeter Trim]
MOW TO SCHEDULE
Mow to schedule mode performs a cut according to a
set mowing schedule. Two options can be selected in
this mode: schedule cut and schedule trim.
1. Perform one of the following:
●[Schedule Cut]: The user can set a maximum
of 3 mowing operation schedules per day. The
mowing operation schedules can be selected
through the control panel or via the app.
●[Schedule Trim]: Enables or disables the trim
action option per day.
●[YES]: Confirm mow to schedule mode.
●[NO]: Select another mode.
NOTE: If trim action is enabled simultaneously with
a scheduled cut, trim action will be performed at the
start time of a scheduled cut. The scheduled cut will
be performed after the scheduled trim.
NOTE: If trim action is enabled for a day and no
schedule cut is set, trim action will be enabled at 11
AM on that day. Time for trim action with no active
schedule cut is non-configurable.
2. Start the product. Close the control panel cover to
continue. The product starts cutting grass according
to a set mowing schedule.
MANUAL
Manual mode performs a continuous, 24/7 mowing
operation.
1. Perform one of the following:
●[Continuous]: The mower will mow continuously
until the user presses the stop button, the
mower goes into a fault state, or the mower is
paused via the app. Press the confirm button
to continue.
●[Until Schedule]: The mower will mow
continuously until a set mowing schedule. Press
the confirm button to continue.
2. Start the product. Close the control panel cover
to continue. The product starts cutting grass in a
random pattern.
PERIMETER TRIM
Perimeter trim performs a cut within close proximity to
the boundary wires. After the perimeter trim, the mower
will either go back to the charging station or continue
with the set cutting mode.
1. Perform one of the following:
●[YES]: Confirm perimeter trim mode.
●[NO]: Select another mode.
NOTE: If a mowing schedule was set and is active
after the perimeter trim, the mower will continue
operation as scheduled. If the cutting mode was set to
manual after the perimeter trim, the mower will resume
operation after the user presses the confirm button.
2. Start the product. Close the control panel cover to
continue. The product starts cutting grass within the
set perimeter.
SETTING A SCHEDULE
Use the schedule to set the day and time for the
mowing operation.
1. Choose the day, then press the confirm button.
2. Choose the time.
a. Mark the start time.
b. Press the confirm button to set start time.
c. Mark the end time.
d. Press the confirm button to set end time.
e. With [Save and Continue] highlighted, press the
confirm button to continue.
NOTE: Highlight [Copy] to apply the same schedule
to the other days. Highlight the day that will have the
same schedule. Repeat the step to apply the same
schedule to the other days.
3. On the daily schedule screen, finalize the settings.
●[Edit]: Edit the displayed schedule.
●[ON], [OFF]: Activate or deactivate trimming
action.
With [Confirm] highlighted, press the confirm button
to save the schedule.
4. An overview of your schedule appears. Press the
confirm button to save settings.
NOTE: A top bar indicates a trimming action on a
certain schedule.

ENGLISH
16
CONFIGURING THE PRODUCT
Choose [ ] to configure the following settings:
●Mowing Parameters
●Advanced Settings
●Perimeter Test Run
MOWING PARAMETERS
1. From the [Settings] screen, choose [Mowing
Parameters]. A list of mower settings appears.
2. Update the following mower settings:
●[Cut Height]: Sets the distance between the
blade disc and the levelled ground surface. The
cut height setting is from H1 (20 mm) to H9 (60
mm) in 5 mm increments.
●[Docking Direction]: Sets the direction of the
mower when docking towards the charging
station.
●[Drive Over Wire Distance]: Sets the distance
that the mower can drive over the boundary
wire.
●[Back Up Distance]: Sets how far the mower
backs up after hitting an obstacle. The mower
will turn at a specified exit angle once the
maximum back-up distance is reached.
●[Exit Angle Range]: Sets the maximum angle
of rotation before the mower starts to move
forward.
3. Press the back button to return to the [Mowing
Parameters] menu.
ADVANCED SETTINGS
1. From the [Settings] screen, choose [Advanced
Settings]. A list of system settings appears.
●[Blade Life Counter]: Shows the blade usage in
days. Blade replacement will be recommended
after maximum count is reached.
●[Security PIN]: Allows the user to change the
pre-set security PIN.
●[Language]: Allows the user to change the pre-
set language option.
●[Perimeter Trimmer]: Enables or disables the
perimeter trimmer option. This setting must be
enabled if the user wants to use the installed
perimeter trimmer assembly.
●[Wi-Fi]: Allows the user to reconfigure the pre-
set Wi-Fi setting.
●[Date/Time]: Allows the user to change the date
and time settings.
●[Product info.]: Allows the user to view the
product specific information.
●[Factory Settings]: Allows the user to perform
a factory reset. After a factory reset, the user
must perform the “Setting up for first-time use”
process without the security PIN setup.
2. Press the back button to return to the [Advanced
Settings] menu.
CHANGING SECURITY PIN
1. From the [Advanced Settings] screen, choose
[Security PIN].
2. Press the confirm button to continue.
3. Enter your current PIN. Press the confirm button.
Repeat the step to choose the succeeding digits of
your security PIN.
4. Enter your new PIN. Press the confirm button.
Repeat the step to choose the succeeding digits of
your security PIN.
5. Re-enter your new PIN. Press the confirm button.
Repeat the step to choose the succeeding digits of
your security PIN.
6. If the security PIN setup is successful, a confirmation
screen appears.
7. Press the confirm button to return to the [Settings]
menu.
WI-FI SETUP
1. From the [Wi-Fi Setup] screen, choose [YES].
2. Press the confirm button to continue.
3. Select one of the following:
●[Setup via the app]: Set up the Wi-Fi connection
using the app.
●[Setup Wi-Fi here]: Set up the Wi-Fi connection
using the control panel.
4. If Wi-Fi connection is set up using the control panel,
select [Auto Scan] or [Manual setup].
●[Auto scan]: Automatically scans for available
Wi-Fi connections.
●[Manual setup]: Enter the Wi-Fi connection
details.
Wi-Fi Setup: Auto Scan
The product automatically scans for available Wi-Fi
networks.
Once connections are detected, the list of available
Wi-Fi networks appears.
To select a Wi-Fi network:
1. Select a Wi-Fi network to connect to.
2. Enter the password.
3. Press the confirm button to connect to the
Wi-Fi network. If connection is successful, a
confirmation screen appears.
4. Press the confirm button to return to the menu.
Wi-Fi Setup: Manual Setup
The Manual Wi-Fi Setup screen appears.

EN
SV
DA
NO
FI
DE
FR
ES
IT
PT
NL
RU
PL
HU
CS
RO
SK
HR
ET
LT
LV
SL
BG
TR
UK
ENGLISH
17
To set up Wi-Fi manually:
1. Enter the network name.
2. Choose the security level.
3. Enter the password.
4. Press the confirm button to connect to the Wi-Fi
connection. The product attempts to connect to
the selected network.
5. If connection is successful, a confirmation
screen appears. Press the confirm button to
return to the menu.
DATE/TIME SETUP
1. From the [Date/Time Setup] screen, choose the
date.
a. With [dd] highlighted, choose the day. Press the
confirm button.
b. With [mm] highlighted, choose the month. Press
the confirm button.
c. With [yy] highlighted, choose the year. Press the
confirm button.
2. Choose the time.
a. With [--:] highlighted, choose the hour. Press the
confirm button.
b. With [:--] highlighted, choose the minute. Press
the confirm button.
3. Press the confirm button.
MOWING ZONES
MOWING ZONE A
■Mowing Zone A has a basic lawn layout. The lawn is
free from obstacles.
■The robotic lawn mower can move unobstructed
from one point to another.
■Lay the wire 45 cm away from the perimeter edge.
MOWING ZONE B
■Mowing Zone B has a basic lawn layout, with
obstacles.
■The lawn is the same size as Mowing Zone A
but uses 50% more wires due to the number of
obstacles.
■Parallel wires to and from each obstacle should
have a gap of less than 5 cm between each wire.
■The gap between an obstacle and the perimeter
should be 90 cm minimum.
■The gap between each obstacle should be 90 cm
minimum.
■Lay the wire 45 cm away from the obstacles.
■Lay the wire 45 cm away from the perimeter edge.
MOWING ZONE C
■Mowing Zone C has an L-shaped lawn layout, with
obstacles.
■Parallel wires to and from each obstacle should
have a gap of less than 5 cm between each wire.
■The gap between an obstacle and the perimeter
should be 90 cm minimum.
■The gap between each obstacle should be 90 cm
minimum.
■Lay the wire 45 cm away from the obstacles.
■Lay the wire 45 cm away from the perimeter edge.
MOWING ZONE D
■Mowing Zone D has a U-shaped lawn layout, with
obstacles.
■The two sides of the lawn are connected by a
narrow passage.
■The narrow passage should have a width of 90 cm
minimum.
■Lay the wire 45 cm away from the perimeter edge.
MOWING ZONE E
■Mowing Zone E has an irregularly shaped lawn
layout, with a narrow passage in between.
■The lawn has obstacles but has an open perimeter
(no obstacles around edges).
■Parallel wires to and from each obstacle should
have a gap of less than 5 cm between each wire.
■The gap between an obstacle and the perimeter
should be 90 cm minimum.
■The gap between each obstacle should be 90 cm
minimum.
■Lay the wire 45 cm away from the obstacles.
■Lay the wire 45 cm away from the house.
■Lay the wire 10 cm away from open perimeter, or
any level paving stones around the house.
MOWING ZONE F
■Mowing Zone F has split lawns, with a narrow
passage in between.
■Both lawns are free from obstacles.
■The narrow passage should have a width of 90 cm
minimum.
■Lay the wire 45 cm away from the obstacles.
■Lay the wire 45 cm away from the perimeter edge.
MOWING ZONE G
■Mowing Zone G has split lawns (Lawn A and Lawn
B).
■The lawns are separate, with an obstacle in
between but with parallel wires connecting Lawn A
to Lawn B.

ENGLISH
18
■Lay the wire 45 cm away from the obstacles.
■Lay the wire 45 cm away from the perimeter edge.
■The parallel wires should be laid in a safe location
and free from disturbance.
■The docking station is placed in Lawn A. To cut
Lawn B, the robotic lawn mower is carried from
Lawn A to B. In Lawn B, run the robotic lawn mower
in Manual Mode for the required time to complete
the task. Once Lawn B is complete, the robotic
lawn mower is carried back to Lawn A. In Lawn A,
place the robotic lawn mower in dock to recharge.
If desired, to continue with Lawn A, set the robotic
lawn mower back to Schedule Mode.
MOWING ZONE H
■Mowing Zone H has split lawns (Lawn A and Lawn B).
■The lawns are separate, with an obstacle in
between and no path for the wires to connect Lawn
A and Lawn B.
■The robotic lawn mower is unable to drive
autonomously between the lawns.
■To mow each garden, the docking station should
be moved, or a second docking station should be
purchased.