RZproducts DCM Agent 32DI 2PS User manual

We protect IT
QUICK START GUIDE
DCM Agent 32DI 2PS
RZproducts GmbH
In der Aue 2 .57584 Wallmenroth .Germany .Tel. [phone] .Fax [phone]
[e-mail] .rz-products.com

We protect IT
Connections of your “DCM Agent”
1. “1U 19 inch brackets” - 2x pcs for mounting into a 1U 19” rack slot.
2. “Logo sticker” - Displays article number of the monitoring unit.
3. “Sticker space” - A place for a sticker, can be used by a user to place an identifier
of the system.
4. “Analog sensors: A1..A8” - 8 RJ12 analog sensor inputs with auto-sensing.
5a. “LEDs: E1, E2” - status indicators for x2 12V 0.25A outputs at the back of the unit.
The LED is ON (orange) - the output is ON (the initial state can be configured).
The LED is OFF (orange) - the output is OFF ((the initial state can be configured).
“LEDs: R1, R2” - status indicators for x2 relays at the back of the unit.
The LED is ON (orange) - the relay is ON (the initial state can be configured).
The LED is OFF (orange) - the output is OFF (the initial state can be configured).
5b. “LED: ACT” - green LED indicates appliance system status,
“LED: CAN” - green LED indicates CAN bus status.
The LED blinks slowly - nothing is connected
The LED blinks fast - configuration is in process
The LED glows constantly - connected to CAN devices
“LED: HDD” - green LED indicates 2.5” HDD or SSD status.
“LED: ERR” - red LED indicates error and traffic. (The operating mode of the device:
If everything is normal, the LED is extinguished, if not - there’s a constant glow;
Software update mode: switches at a rate of 2 times per second;)
5c. “LED: TX” - Modbus data sent activity (Transmission).
“LED: RX” - Modbus data received activity (Receiving).
6. “Modem slot”
7. “LAN port” - Ethernet 10/100 Base-T port, provides an Ethernet connection.
“Orange LED” - orange LED for Ethernet port. Shows network traffic.
“Green LED” - green LED for Ethernet port. Shows network traffic. Flashes green when
the system starts up. Shows the connection state (constant green light - the connection
is established, blinking green - the connection attempt).
8. “CAN DEVICES” - digital connector RJ12 for the connection of CAN sensors and CAN
extensions on a CAN bus, with auto-sensing. Modules can be chain together.
9. Buttons
9a. “Restart” - the button restarts the appliance. Hold the button for 2 seconds and
then let go, the system will restart.
9b. “FEL” - user-defined action button. This button is reserved for future functions.
9c. “Shutdown” - softly shuts down the device. Hold for several seconds and then let go.
10. “SD card” - MicroSD card slot with an ejector. The card is needed for data storage or
system restore.
11-12. USB ports are needed for USB camera recording, USB Flash for system logs, and
system restore.
11. “USB 0” - type miniAB USB-port 2.0, required to connect a USB camera.
12. “USB 1”- type USB-port 2.0, required to connect a USB camera or a USB Flash card.
13. “DRY CONTACT INPUTS 1...32” - Digital inputs (Type IN).
14. “ISOLATED DRY CONTACTS OUTPUTS 1...8” - Digital outputs 24VDC / 15mA (type OUT).
15. DCM Agent has 2x power inlets, providing a redundant power supply.
15a. “RESERVE”- Reserve power inlet. 100-240VAC, 50/60Hz, Fuse 2A, Fuse 5x20mm, type C14.
15b. “MAIN” - Power inlet. 100-240VAC, 50/60Hz, Fuse 2A, Fuse 5x20mm, type C14.
16. AV camera input, output, and a power supply.
16a. “ AV OUT” - Audio / video output. You can connect it to a monitor or other external device.
16b. “AV IN” - Audio / video input. Video/audio can be recorded if HDD is installed.
16c. “DC OUTPUT 12V 0.25A Camera PWR” - 12V 0.25A output electronic relay terminal.
17. “OUTPUTS 12V 0.25A” - 12V 0.25A (for each output) terminals outputs (electronic relay).
18. “MODBUS” - port for connecting Modbus RTU / RS-485 sensors and devices.
19. “1-WIRE READER” - For connecting RFID reader or 1-Wire sensors.
20. “Relays 1, Relay 2” - NC / NO power relay terminals.
21. “Chassis grounding” - Chassis grounding, M4 thread. Enhances the immunity of the
equipment against conducted and radiated RF disturbances. Please contact a
professional electrician before connecting it.
Attention: In order to access the Monitoring System web interface, your com-
puter must be on the same network! To ensure this, please set the subnet
mask 255.255.255.0 and the IP address 192.168.0.xxx on your computer.
Xxx stands for a number between 0 and 254.
Connecting to the unit by IP
All RZ-Products monitoring systems have an integrated web interface. To access this interface,
you must first open a web-Browser. Enter the IP address of your „DCM Agent” in the input line of your browser.
Attention: RZ-Products Monitoring systems use HTML5. Please make sure you are using the latest version
of your browser. System interface was tested under Chrome, Firefox and Safari.
2 Hostname DCM Agent
3 IP-address 192.168.0.101
4 Network mask 255.255.255.0
5 Broadcast 192.168.0.1
6 Gateway 192.168.0.255
7 Primary DNS 192.168.0.1
1 DHCP client switched off
Default user name: guest Default password: guest
log in as “guest” and configure the users and their rights.