S-products MP 2-wire series User manual

MP82710H & MP88710H
MP82710 & MP88710
MP82810 & MP88810
MP82820-R & MP88820-R
Mp82820-T & Mp88820-T
Mp82830-T
Mp82000D
Mp82830-R
S-Products B.V.
S-Products Inc.
Nijverheidscentrum 26, NL-2761JP Zevenhuizen, The Netherlands, , Fax: [phone]
9919 Valley View Drive, Eden Prairie, MN 55344, USA, Tel: [phone], Fax: [phone]
E-mail: [email protected] Internet: www.s-products.com
Tel: [phone]
Document No. Manual MP 2-wire.cdr - Issue 150616

SPECIFICATIONS
Our Microprocessor based transmitters are divided in the 2 wire headmount series Mp82000, the rail mount
series Mp88000 and the 4 wire Mp87000. NOTE: The 4 wire transmitters are not described in this manual!
All models are
GENERAL INTRODUCTION:
easily programmed via a personal computer with our software and interface.
CONTENTS
Type overview
Specifications
ATEX
Safety instructions
Connection diagram
Instructions & programming for all Mp type transmitters
Dimensions
EC Declaration of Conformity
ATEX certificate
WARRANTY
Our transmitters have a 5 year warranty.
Follow usage instruction in this manual.
In case of malfunction return to your supplier.
* ATEX certification optionally available
1)
2)
Mp82000D is a plug-in display optionally available for all Mp82*10* headmounting transmitters.
Mp87000D is a plug-in display optionally available for all Mp87*00 4-wire railmounting transmitters
Page 2
Page 2 / 3
Page 4
Page 5
Page 6
Page 7 / 8
Page 9
Page 10
Page 11
Model Headmount Railmount 2-wire 4-wire RTD only T/C only All inputs Isolated Hart® ATEX
Mp82820-R •••
Mp82830-R •••
Mp82820-T •• •
Mp82830-T •• •
Mp82810 •• •
Mp82710 •• ••*
Mp82710H • • •••*
Mp82000D1) •*
Mp88820-R •• •
Mp88820-T •• •
Mp88810 •• •
Mp88710 •• •• *
Mp88710H •• •••*
Mp87800 •• •
Mp87700 •• ••
Mp87000D2) •
Page 2
S-Products B.V.
S-Products Inc.
Nijverheidscentrum 26, NL-2761JP Zevenhuizen, The Netherlands, , Fax: [phone]
9919 Valley View Drive, Eden Prairie, MN 55344, USA, Tel: [phone], Fax: [phone]
E-mail: [email protected] Internet: www.s-products.com
Tel: [phone]
Document No. Manual MP 2-wire.cdr - Issue 150616

Housing Material Mp82
Dimensions
Dimensions With Read-out
Housing Material Mp88
Dimensions
Zinc Alloy (ZAMAK 5), Epoxy coated
43mm Dia. x 27mm H.
43mm Dia. x 36mm H.
Makrolon
75mm H. X 22.5mm W x 99mm D.
Specifications
Minimum Span
Output
Linearization
Supply *) Polarity protected
Supply effect
Zero Drift
Span Drift
Long term Drift
Cold Junction Drift
Excitation Current RTD
Sensor Lead Resistance RTD
Sensor Lead Resistance Effect
Sensor Lead Resistance T/C
Open Circuit Detection
Load Capability
Start Up Time
Warm Up Time
Isolation
Ambient Operating Temperature
Storage Temperature
Mp82810 / Mp88810 Mp82710(H) / Mp88710(H)
Input RTD: Pt100, Pt250, Pt500, Pt1000
Ni100, Ni500, Ni1000, Cu10, Cu100
T/C: K, J, T, E, L, U, R, S, B, C, D, N
Volt & Ohm
RTD: 25°C
T/C: 50°C
4...20 mA / 20...4 mA
On / Off
5...40 VDC
0.001% / V
0.01%/°C or 0.02°C/°C
0.01%/°C or 0.01°C/°C
0.05%/year
0.03 °C/°C
0.1 mA
500 Ohm max.
0.005 °C/Ohm
10,000 Ohm max.
Upscale / Downscale
Vbat-5V / 20mA
10 sec
2 min
none
-40°C...+85°C
-40°C...+100°C
++
++
+
+
RTD: Pt100, Pt250, Pt500, Pt1000
Ni100, Ni500, Ni1000, Cu10, Cu100
T/C: K, J, T, E, L, U, R, S, B, C, D, N
Volt & Ohm
4...20 mA / 20...4 mA
On / Off
5...40 VDC (H 12...40VDC)
0.003% / V
0.01%/°C or 0.02°C/°C
0.01%/°C or 0.02°C/°C
0.05%/year
0.03 °C/°C
0.1 mA
500 Ohm max.
0.005 °C/Ohm
10,000 Ohm max.
Upscale / Downscale
Vbat-5V / 20mA (H: Vbat-12V / 20mA)
10 sec
2 min
1500 V AC / 1 min.
-40°C...+85°C
-40°C...+100°C
RTD: 25 °C
T/C: 50 °C
++
++
+
+
Specifications Mp82820-R / Mp82830-R / Mp88820-R Mp82820-T / Mp82830-T / Mp88820-T
Input
Minimum Span
Output
Linearization
Cold junction compensation
Supply *)
Sensor Lead Resistance RTD
Sensor Lead Resistance T/C
Open Circuit Detection
Load Capability
Start Up Time
Warm Up Time
Isolation
Ambient Operating Temperature
Storage Temperature
Polarity protected
RTD: Pt100, Pt250, Pt500, Pt1000,
Ni100, Ni500, Ni1000, Ohm
25°C
4...20 mA or 20...4 mA
On / Off
5...40 VDC
500 Ohm max.
Upscale / Downscale
Vbat-5V / 20mA
15 sec
2 min
none
-40°C...+85°C
-40°C...+100°C
*) NOTE: For ATEX approved equipment different power requirements may apply!
Housing Material Mp82820/30
Dim.
Housing Dim. with cover
Housing Material Mp88
Dimensions
Mp82820
Mp82830
Makrolon
43mm Dia. x 23mm H.
49mm Dia. x 25mm H.
Makrolon
75mm H. X 22.5mm W x 99mm D.
43mm Dia. x 21mm H.
T/C: K,J,T,E,N
50°C
4...20 mA or 20...4 mA
On / Off
On / Off
5...40 VDC
500 Ohm max.
10,000 Ohm max.
Upscale / Downscale
Vbat-5V / 20mA
15 sec
2 min
none
-40°C...+85°C
-40°C...+100°C
Page 3
S-Products B.V.
S-Products Inc.
Nijverheidscentrum 26, NL-2761JP Zevenhuizen, The Netherlands, , Fax: [phone]
9919 Valley View Drive, Eden Prairie, MN 55344, USA, Tel: [phone], Fax: [phone]
E-mail: [email protected] Internet: www.s-products.com
Tel: [phone]
Document No. Manual MP 2-wire.cdr - Issue 150616

ATEX
Some models of the MP series are
GENERAL:
available in an intrinsically
safe version and meet the requirements of the ATEX directive
94/9/EC.
All ATEX approved units carry the following labels:
MARKING:
Year of production
Serial No. i.e.:
General product labels
Certificate Number, see certificate on page 11:
Mp82710, Mp82710H, Mp88710, Mp88710H, Mp82000D
DEKRA 11ATEX0105 X
++
MODEL
RANGE
INPUT
OUTPUT
POWER
S-Products
NETHERLANDS - SINGAPORE - USA
Mp88710
0...1000°C
Thermocouple K
4...20 mA
10...40 V DC
2-WIRE TRANSMITTER Mp 827102-WIRE TRANSMITTER Mp 82710
INPUT
OUTPUT 4 - 20 mA
RANGE
Thermocouple K
0...1000°C
C04164
Ex ia IIC T4/T5/T6 Ga See certificate for data
30V 100mA 750mWUI P
ii i
<<<
S-Products BV
Nijverheidscentrum 26, NL-
Mp8xx10-series
DEKRA 11ATEX0105 X
0344 II 1 G
2761 JP
.
2013
Parameters for products certified with certificate DEKRA 11ATEX0105 X, see also page 11:
U
I
P
C
Supply circuit:
= 30 V DC
= 100 mA
= 750 mW
=
I
I
I
I
LI= 0 mH
0 nF
0344 = CE marking Notified Body
II = Group
1 G = Category 1, Gas
ia = intrinsic safety
IIC = Hydrogen and Acetylene Gas
T4...T6: Temperature Classification
0344 II 1 G
Ex ia IIC Ga
T4 (T -40...+85°C)
T5 (T -40...+75°C)
T6 (T -40...+60°C)
amb
amb
amb
U
I
P
C
Input circuit:
= 6,3 V DC
= 165 mA
= 242 mW
=
o
o
o
o
Lo= 1 mH
34,5 µF
SENSOR
HAZARDOUS AREA
NON-HAZARDOUS AREA
DC
POWER
ZENER
BARRIER
EX
TRANSMITTER
+
-
+
-
Apparatus
without
further
specification
Mp82710, Mp82710H, Mp88710, Mp88710H and Mp82000D:
Page 4
S-Products B.V.
S-Products Inc.
Nijverheidscentrum 26, NL-2761JP Zevenhuizen, The Netherlands, , Fax: [phone]
9919 Valley View Drive, Eden Prairie, MN 55344, USA, Tel: [phone], Fax: [phone]
E-mail: [email protected] Internet: www.s-products.com
Tel: [phone]
Document No. Manual MP 2-wire.cdr - Issue 150616

SPECIAL CONDITIONS FOR SAFE USE:
For electrical data and temperature data see EC-Type examination certificate DEKRA 11ATEX0105 X
on page 11.
NORMATIVE REFERENCE:
The transmitters Mp82710, Mp82710H, Mp88710, Mp88710H and plug-in display Mp82000D have an EC
Type examination certificate issued by DEKRA and have been approved to the standards mentioned on the
certificate of conformity (see page 10) and the EC-Type examiniation certificate DEKRA 11ATEX0105 X
(see page 11).
INSTALLATION REQUIREMENTS:
- ATEX approved equipment is only to be connected to a Zenerbarrier.
The Temperature Transmitter must be mounted in an enclosure providing a degree of ingress protection of at
least IP20 per EN 60529.
This enclosure must be in conformance with Clauses 4.3 and 4.4 of EN 50284, when the Temperature
Transmitter is mounted in an area where the use of category 1 G apparatus is required.
This enclosure must be in conformance with Clauses 7.3 and 8.1 of EN 50014, when the Temperature
Transmitter is mounted in an area where the use of category 2 G apparatus is required.
The mentioned Clauses describe how to avoid danger of ignition due to electrostatic charges.
- All transmitters Mp82000 and Mp88000 have an ingress protection of IP20.
This requires usage in a dry, clean and well controlled environment.
Mount the Mp82000 transmitter in a (DAN) head as described below..
- It is prefered to use twisted pair, shielded cable to connect the transmitter to its power supply in order to
obtain the best immunity to Electromagnetic signals. On the power supply side connect the shield to the
power supply’s earthing point, on the transmitter side connect the shield to the grounded head
somewhere close to the transmitter.
Make sure the transmitter is firmly connected to the head.
MOUNTING in CONNECTION HEAD
1. Screw M4
2. Transmitter
3. Measuring insert plate
4. Ferrule
5. Spring
6. Notch
1
2
5
6
43
Page 5
S-Products B.V.
S-Products Inc.
Nijverheidscentrum 26, NL-2761JP Zevenhuizen, The Netherlands, , Fax: [phone]
9919 Valley View Drive, Eden Prairie, MN 55344, USA, Tel: [phone], Fax: [phone]
E-mail: [email protected] Internet: www.s-products.com
Tel: [phone]
Document No. Manual MP 2-wire.cdr - Issue 150616

CONNECTIONS
Interface connector
also used for connecting the optional display unit (Mp82810 / Mp82710(H) only).
Interface connector
behind removable
cover.
and Output loopcurrent 4-20 mA
DC Power
Input signals
TC/mV RTD
+
-
Mp88820-R / Mp88820-T / Mp88810 / Mp88710(H)
Mp82710(H) / Mp82810
+
+-
RTD
-
mV / TC
RTD
Mp82830-R
DC
Power
+
-
DC
Power&
4-20mA
+
-
Mp82820-R
DC
Power +
-RTD
Page 6
S-Products B.V.
S-Products Inc.
Nijverheidscentrum 26, NL-2761JP Zevenhuizen, The Netherlands, , Fax: [phone]
9919 Valley View Drive, Eden Prairie, MN 55344, USA, Tel: [phone], Fax: [phone]
E-mail: [email protected] Internet: www.s-products.com
Tel: [phone]
Document No. Manual MP 2-wire.cdr - Issue 150616

General Instructions for the user
(not required for factory calibrated transmitters)
1. Insert the CD-ROM into your computer.
The Software will start automatically. (Or you may run MpUser_Setup_V44.exe)
Just follow the on-screen instructions.
Required is at least Windows 98 or NT and 1MB free space.
2. Connect the interface to the USB port of your computer.
Attach the interface to the transmitter.
Start the installed S-PRO Mp - software by clicking the "S"-icon.
First click Upload to read the settings from your transmitter.
Select the required parameters and download these into the transmitter.
3. After programming you may connect the transmitter as shown in the
connections drawing.
4. An optional display unit may be connected to the interface connector
(Mp82 and Mp87 series), after connecting power and a sensor.
HART protocol transmitters
®
Selecting sensor and range can be done exactly the same as described before for all
our transmitters with the MP software.
In order to use HART protocol you need a HART compatible interface and software
or a handheld terminal.
Connect with a resistor in the loop as required by HART.
The transmitters know 14 universal commands and 5 common-practice commands:
0 Read unique identifier (ID)
1 Read primary variable
2 Read current and % of range
3 Read current and 4 (2) dynamic var
6 Write polling address
11 Read unique ID associated with tag
12 Read message
13 Read tag, descriptor, date
14 Read PV sensor information
15 Read output information
16 Read final assembly number
17 Write message
18 Write tag, descriptor, date
19 Write final assembly number
34 Write damping value
35 Write range values
40 Enter/Exit fixed current mode
49 Write PV sensor
59 Write # of response preambles
Note:
It is not possible to change °C into °F
or vice versa with a HART command.
Use the S-Pro Mp software to program
the transmitter
Page 7
S-Products B.V.
S-Products Inc.
Nijverheidscentrum 26, NL-2761JP Zevenhuizen, The Netherlands, , Fax: [phone]
9919 Valley View Drive, Eden Prairie, MN 55344, USA, Tel: [phone], Fax: [phone]
E-mail: [email protected] Internet: www.s-products.com
Tel: [phone]
Document No. Manual MP 2-wire.cdr - Issue 150616

S-PRO MpUser Software
General
This program uses the basic Windows features like Save, Print, and Exit.
We refer to the Windows Help Manual for file handling.
Without a mouse you can reach the menu-items pressing both ALT
and the underlined key. You can jump between the settings with TAB.
®
It is possible to save your settings for
later use, to open a previous configuration
or to print the present configuration. Either click on ile or on one of the icons.
The large Upload and Download buttons are also located under ction.
With a transmitter connected use to find out the settings of your transmitter.
After you made the required selections use to program the transmitter.
S ttings is an important menu item. Here you can select or and the port. You can check which
COM-port has been assigned to the interface in your Windows Hardware Configuration Screen.
1. ile - ction - S ttings
Upload
Download
°C °F COM
FA e
F
A
e
NOTE: Make sure to switch the on-screen readout Off, otherwise you can't alter the settings!
:
: You may select the input sensor from a list. The choice is limited by the transmitter type.
Thermocouple alloys are mentioned.
and : Input values for output current start and end.
Default are the range minimum and maximum of the selected sensor.
and : Any comment you'd like to add. (max. 16 characters)
: The number of lead wires on your RTD sensor (i.e. Pt100).
: Set to 50 Hz for Europe and 60 Hz for USA.
: Cold Junction Compensation for Thermocouples.
: Fixation of the loopcurrent on sensor malfunction.
: Choose min...max = 4...20 mA or 20...4 mA
: Select On to linearize the input curve, or Off if you require the output curve to be
the same as the input.
: Select High for high sample rate, or Normal for standard sample rate.
2. Settings
Transmitter
Sensor
Minimum Maximum
Tag 1 Tag 2
Connection
Filter
CJ Comp
Sensor Break
Output Current
Linearization
Sample Rate
Use Upload to automatically detect transmitter model connected (connect transmitter first).
(Mp87000: The 0..1V/10V/0..20mA is automatic)
: Read the configuration from the transmitter.
: Write your settings to the transmitter.
Upload
Download
3. On-Screen
Readout
In the Sensor display
you'll see the actual
input value provided
the programmed
sensor is connected.
Loopcurrent is a
calculated value.
Click On to
start and Off
to stop the
on-screen display.
You must turn the
on-screen display
off before changing
settings.
Note that you will only get a
Sensor / Loopcurrent readout
on screen if the transmitter
is connected to a sensor.
1.
3.
New Open Save Print
2.
Page 8
S-Products B.V.
S-Products Inc.
Nijverheidscentrum 26, NL-2761JP Zevenhuizen, The Netherlands, , Fax: [phone]
9919 Valley View Drive, Eden Prairie, MN 55344, USA, Tel: [phone], Fax: [phone]
E-mail: [email protected] Internet: www.s-products.com
Tel: [phone]
Document No. Manual MP 2-wire.cdr - Issue 150616

75 mm
2.95 "
22.5 mm
0.89 "
99 mm
3.90 "
Mp88710(H)
Mp88810
Mp88820-R
Mp88820-T
33 mm
1.30 "
43.3 mm
1.70 "
20 mm
0.79 "
5 mm
0.2 "
M4
47 mm 1.85 "
10 mm 0.4 "
17 mm
0.67 "
43.3 mm
1.70 "
20 mm
0.79 "
36 mm
1.42 " 5 mm
0.2 "
DIMENSIONS
Mp82710(H)
Mp82810
Mp82710(H) with display
Mp82810 with display
49 mm 1.93 "
43 mm
1.69 "
14 mm
0.55 "
5 mm
0.2 "
13 mm
0.51 "
25 mm
0.98 "
33 mm
1.30 "
8 mm 0.31 "
Mp82820-R Mp82830-R
49 mm 1.93 "
43 mm
1.69 "
14 mm
0.55 "
9 mm
0.35 "
13 mm
0.51 "
25 mm
0.98 "
33 mm
1.30 "
8 mm 0.31 "
Page 9
S-Products B.V.
S-Products Inc.
Nijverheidscentrum 26, NL-2761JP Zevenhuizen, The Netherlands, , Fax: [phone]
9919 Valley View Drive, Eden Prairie, MN 55344, USA, Tel: [phone], Fax: [phone]
E-mail: [email protected] Internet: www.s-products.com
Tel: [phone]
Document No. Manual MP 2-wire.cdr - Issue 150616

ce-cert.cdr/F/291003
EU DECLARATION OF CONFORMITY
Signature Zevenhuizen, 16 April 2016
DECLARATION DE CONFORMITE CE EG BESCHEINIGUNG DER ÜBEREINSTIMMUNG
S-Products b.v.
S-Products b.v.
P.O. Box 33
2760 AA Zevenhuizen
The Netherlands
Phone: (31) 180 - 633455
FaxInt: (31) 180 - 633644
Generic emission standard and
Generic immunity standard from which
Radiated electromagnetic field
Fast transient immunity
HF conducted immunity
EN 50081-1, 1992
EN 50082-2, 1995
ENV 50140, 1993
EN 61000-4-4, 1995
ENV 50141, 1993
ATEX directive 114/34/EU DEKRA 11ATEX0105 X
Ex 1G EX ia IIC T4...T6 Ga
Dekra Certification B.V., Meander 1051, 6825 MJ Arnhem, The Netherlands
EN 60079-0 : 2012 EN 60079-11 : 2012 EN 60079-26 : 2007
Notified body number 0344 Mp82710-Ex
Mp88710-Ex
Mp82710H-Ex
Mp88710H-Ex
Mp82000D-Ex
We declare under our sole responsibilty that
products to which this declaration relates is
in conformity with the mentioned specifications
following the provisions of Council Directive
89/336/EE and ATEX directive 114/34/EU on
the approximation of the laws of the Member
States relating to Electromagnetic Compatibility.
Nous déclarons sous notre entière responsabilité
que les produits cités dans cette déclaration sont
en conformité avec les spécifications rappelées
ici et respectent les réserves de la Directive
89/336/EEC du Conseil et ATEX directive 114/34/EU
visant au rapprochement des textes de lois des
États Membres se rapportant à la compatibilité
électromagnétique.
Wir erklären, allein verantwortlich, nach der Richtlinie
des Rates der Europäischen Gemeinschaft
89/336/EEC und ATEX Richtlinie 114/34/EU, daß jene
Produkte auf die sich diese Bescheinigung bezieht,
in Übereinstimmung mit den hormonisierten
Europäischen Normen über Elektromagnetische
Verträglichkeit, gefertigt sind.
Page 10
S-Products B.V.
S-Products Inc.
Nijverheidscentrum 26, NL-2761JP Zevenhuizen, The Netherlands, , Fax: [phone]
9919 Valley View Drive, Eden Prairie, MN 55344, USA, Tel: [phone], Fax: [phone]
E-mail: [email protected] Internet: www.s-products.com
Tel: [phone]
Document No. Manual MP 2-wire.cdr - Issue 150616

Page 11
S-Products B.V.
S-Products Inc.
Nijverheidscentrum 26, NL-2761JP Zevenhuizen, The Netherlands, , Fax: [phone]
9919 Valley View Drive, Eden Prairie, MN 55344, USA, Tel: [phone], Fax: [phone]
E-mail: [email protected] Internet: www.s-products.com
Tel: [phone]
Document No. Manual MP 2-wire.cdr - Issue 150616

Page 12
S-Products B.V.
S-Products Inc.
Nijverheidscentrum 26, NL-2761JP Zevenhuizen, The Netherlands, , Fax: [phone]
9919 Valley View Drive, Eden Prairie, MN 55344, USA, Tel: [phone], Fax: [phone]
E-mail: [email protected] Internet: www.s-products.com
Tel: [phone]
Document No. Manual MP 2-wire.cdr - Issue 150616